ASTM F 1789 : 2022
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Terminology for F16 Mechanical Fasteners
Available format(s)
Hardcopy , PDF
Superseded date
11-28-2023
Superseded by
Language(s)
English
Published date
12-02-2022
Important note : All end users must be registered with an Account prior to user licenses being assigned.| Committee |
F 16
|
| DocumentType |
Reference Material
|
| Pages |
15
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This terminology standard provides a compilation of definitions for terminology used for mechanical fasteners.
1.2Terms in this terminology are organized alphabetically. In Appendix X1 they are listed under fastener characteristic.
1.3Additional definitions are shown in ANSI/ASME B18.12; IFI Glossary of Terms, IFI-139 and IFI-140; and SAE J412.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM F 788/F788M : 2020 : EDT 1 | Standard Specification for Surface Discontinuities of Bolts, Screws, Studs, and Rivets, Inch and Metric Series |
| ASTM F 2437/F2437M : 2017 : R2023 | Standard Specification for Carbon and Alloy Steel Compressible-Washer-Type Direct Tension Indicators for Use with Cap Screws, Bolts, Anchors, and Studs |
| ASTM F 2328M : 2017 : R2022 | Standard Test Method for Determining Decarburization and Carburization in Hardened and Tempered Threaded Steel Bolts, Screws, Studs, and Nuts (Metric) |
| ASTM A 153/A153M : 2023 | Standard Specification for Zinc Coating (Hot-Dip) on Iron and Steel Hardware |
| ASTM F 3125/F3125M : 2023 | Standard Specification for High Strength Structural Bolts and Assemblies, Steel and Alloy Steel, Heat Treated, Inch Dimensions 120 ksi and 150 ksi Minimum Tensile Strength, and Metric Dimensions 830 MPa and 1040 MPa Minimum Tensile Strength |
| ASTM F 959/F959M : 2017 : REV A : R2023 | Standard Specification for Compressible-Washer-Type Direct Tension Indicators for Use with Structural Fasteners, Inch and Metric Series |
| ASTM F 2282 : 2023 | Standard Specification for Quality Assurance Requirements for Carbon and Alloy Steel Wire, Rods, and Bars for Mechanical Fasteners |
| ASTM F 2329/F2329M : 2015 : R2023 | Standard Specification for Zinc Coating, Hot-Dip, Requirements for Application to Carbon and Alloy Steel Bolts, Screws, Washers, Nuts, and Special Threaded Fasteners |
| ASTM F 2328 : 2017 : R2022 | Standard Test Method for Determining Decarburization and Carburization in Hardened and Tempered Threaded Steel Bolts, Screws, Studs, and Nuts |
| ASTM F 812/F812M : 2012 : R2022 : EDT 1 | Standard Specification for Surface Discontinuities of Nuts, Inch and Metric Series |
| ASTM A 394 : 2008 : R2015 | Standard Specification for Steel Transmission Tower Bolts, Zinc-Coated and Bare |
| ASTM F 2833 : 2011 : R2017 | Standard Specification for Corrosion Protective Fastener Coatings with Zinc Rich Base Coat and Aluminum Organic/Inorganic Type |
| ASTM A 153/A153M : 2016 : REV A | Standard Specification for Zinc Coating (Hot-Dip) on Iron and Steel Hardware |
| ASTM A 1059/A1059M : 2018 | Standard Specification for Zinc Alloy Thermo-Diffusion Coatings (TDC) on Steel Fasteners, Hardware, and Other Products |
| ASTM F 2282 : 2018 | Standard Specification for Quality Assurance Requirements for Carbon and Alloy Steel Wire, Rods, and Bars for Mechanical Fasteners |
| ASTM A 489 : 2018 : EDT 1 | Standard Specification for Carbon Steel Eyebolts |
| ASTM F 1470 : 2019 | Standard Practice for Fastener Sampling for Specified Mechanical Properties and Performance Inspection |
| ASTM F 436/F436M : 2019 | Standard Specification for Hardened Steel Washers Inch and Metric Dimensions |
| ASTM F 788 : 2020 | Standard Specification for Surface Discontinuities of Bolts, Screws, Studs, and Rivets, Inch and Metric Series |
| ASTM F 3019/F3019M : 2019 | Standard Specification for Chromium Free Zinc-Flake Composite, with or without Integral Lubricant, Corrosion Protective Coatings for Fasteners |
| ASTM F 2660 : 2020 | Standard Test Method for Qualifying Coatings for Use on F3125 Grade A490 Structural Bolts Relative to Environmental Hydrogen Embrittlement |
| ASTM F 3393 : 2020 : EDT 1 | Zinc-Flake Coating Systems for Fasteners |
| ASTM F 1136/F1136M : 2011 : R2019 | Standard Specification for Zinc/Aluminum Corrosion Protective Coatings for Fasteners |
| ASTM A 449 : 2014 : R2020 | Standard Specification for Hex Cap Screws, Bolts and Studs, Steel, Heat Treated, 120/105/90 ksi Minimum Tensile Strength, General Use |
| ASTM F 1554 : 2020 | Standard Specification for Anchor Bolts, Steel, 36, 55, and 105-ksi Yield Strength |
| ASTM A 307 : 2021 | Standard Specification for Carbon Steel Bolts, Studs, and Threaded Rod 60 000 PSI Tensile Strength |
| ASTM F 2832 : 2011 : R2021 | Standard Guide for Accelerated Corrosion Testing for Mechanical Fasteners |
| ASTM F 2482/F2482M : 2021 | Standard Specification for Load-Indicating Externally Threaded Fasteners |
| ASTM A 574 : 2021 | Standard Specification for Alloy Steel Socket-Head Cap Screws |
| ASTM A 354 : 2017 : EDT 2 | Standard Specification for Quenched and Tempered Alloy Steel Bolts, Studs, and Other Externally Threaded Fasteners |
| ASTM A 563/A563M : 2021 : REV A : EDT 1 | Standard Specification for Carbon and Alloy Steel Nuts (Inch and Metric) |
| ASTM F 3125/F3125M : 2022 | Standard Specification for High Strength Structural Bolts and Assemblies, Steel and Alloy Steel, Heat Treated, Inch Dimensions 120 ksi and 150 ksi Minimum Tensile Strength, and Metric Dimensions 830 MPa and 1040 MPa Minimum Tensile Strength |
| ASTM F 812 : 2012 : R2022 | Standard Specification for Surface Discontinuities of Nuts, Inch and Metric Series |
| ASTM F 2328 : 2017 | Standard Test Method for Determining Decarburization and Carburization in Hardened and Tempered Threaded Steel Bolts, Screws, Studs, and Nuts |
| ASTM F 2328M : 2017 | Standard Test Method for Determining Decarburization and Carburization in Hardened and Tempered Threaded Steel Bolts, Screws, Studs, and Nuts (Metric) |
| ASTM F 3043 : 2015 | Standard Specification for “Twist Off” Type Tension Control Structural Bolt/Nut/Washer Assemblies, Alloy Steel, Heat Treated, 200 ksi Minimum Tensile Strength |
| ASTM F 3111 : 2016 | Standard Specification for Heavy Hex Structural Bolt/Nut/Washer Assemblies, Alloy Steel, Heat Treated, 200 ksi Minimum Tensile Strength |
| ASTM F 3148 : 2017 : REV A | Standard Specification for High Strength Structural Bolt Assemblies, Steel and Alloy Steel, Heat Treated, 144ksi Minimum Tensile Strength, Inch Dimensions |
| ASTM F 2329/F2329M : 2015 | Standard Specification for Zinc Coating, Hot-Dip, Requirements for Application to Carbon and Alloy Steel Bolts, Screws, Washers, Nuts, and Special Threaded Fasteners |
| ASTM F 1941/F1941M : 2016 | Standard Specification for Electrodeposited Coatings on Mechanical Fasteners, Inch and Metric |
| ASTM F 2437/F2437M : 2017 | Standard Specification for Carbon and Alloy Steel Compressible-Washer-Type Direct Tension Indicators for Use with Cap Screws, Bolts, Anchors, and Studs |
| ASTM F 959/F959M : 2017 : REV A | Standard Specification for Compressible-Washer-Type Direct Tension Indicators for Use with Structural Fasteners, Inch and Metric Series |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.