ASTM F 1249 : 2006 : R2011
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Water Vapor Transmission Rate Through Plastic Film and Sheeting Using a Modulated Infrared Sensor
Hardcopy , PDF
11-11-2014
English
08-01-2011
Important note : All end users must be registered with an Account prior to user licenses being assigned.| Committee |
F 02
|
| DocumentType |
Test Method
|
| Pages |
5
|
| ProductNote |
Reconfirmed 2011
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1 This test method covers a procedure for determining the rate of water vapor transmission through flexible barrier materials. The method is applicable to sheets and films up to 3 mm (0.1 in.) in thickness, consisting of single or multilayer synthetic or natural polymers and foils, including coated materials. It provides for the determination of (1) water vapor transmission rate (WVTR), (2) the permeance of the film to water vapor, and (3) for homogeneous materials, water vapor permeability coefficient.
Note 1—Values for water vapor permeance and water vapor permeability must be used with caution. The inverse relationship of WVTR to thickness and the direct relationship of WVTR to the partial pressure differential of water vapor may not always apply.
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| ASTM F 2902 : 2016 : EDT 1 | Standard Guide for Assessment of Absorbable Polymeric Implants |
| ASTM F 2150 : 2013 | Standard Guide for Characterization and Testing of Biomaterial Scaffolds Used in Tissue-Engineered Medical Products |
| ASTM C 1729M : 2017 | Standard Specification for Aluminum Jacketing for Insulation |
| ASTM C 1775 : 2014 | Standard Specification for Laminate Protective Jacket and Tape for Use over Thermal Insulation for Outdoor Applications |
| ASTM C 1423 : 2016 | Standard Guide for Selecting Jacketing Materials for Thermal Insulation |
| ASTM F 2097 : 2016 | Standard Guide for Design and Evaluation of Primary Flexible Packaging for Medical Products |
| ASTM D 7407 : 2007 : R2012 | Standard Guide for Determining The Transmission of Gases Through Geomembranes |
| ASTM F 2896 : 2011 : R2017 | Standard Specification for Reinforced Polyethylene Composite Pipe For The Transport Of Oil And Gas And Hazardous Liquids |
| ASTM D 6577 : 2015 | Standard Guide for Testing Industrial Protective Coatings |
| ASTM C 647 : 2019 | Standard Guide to Properties and Tests of Mastics and Coating Finishes for Thermal Insulation |
| ASTM D 4635 : 2016 | Standard Specification for Plastic Films Made from Low-Density Polyethylene and Linear Low-Density Polyethylene for General Use and Packaging Applications |
| ASTM C 1767 : 2016 : REV A | Standard Specification for Stainless Steel Jacketing for Insulation |
| ASTM D 2103 : 2015 | Standard Specification for Polyethylene Film and Sheeting |
| ASTM D 6701 : 2016 | Standard Test Method for Determining Water Vapor Transmission Rates Through Nonwoven and Plastic Barriers |
| ASTM C 1729 : 2017 | Standard Specification for Aluminum Jacketing for Insulation |
| ASTM C 1767M : 2016 : REV A | Standard Specification for Stainless Steel Jacketing for Insulation |
| ASTM E 1745 : 2017 | Standard Specification for Plastic Water Vapor Retarders Used in Contact with Soil or Granular Fill under Concrete Slabs |
| ASTM E 398 : 2013 | Standard Test Method for Water Vapor Transmission Rate of Sheet Materials Using Dynamic Relative Humidity Measurement |
| ASTM E 154/E154M : 2008 : REV A : R2019 | Standard Test Methods for Water Vapor Retarders Used in Contact with Earth Under Concrete Slabs, on Walls, or as Ground Cover |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.