ASTM E 647 : 2023 : REV B
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Measurement of Fatigue Crack Growth Rates
Hardcopy , PDF
07-01-2024
English
11-15-2023
Important note : All end users must be registered with an Account prior to user licenses being assigned.| Committee |
E 08
|
| DocumentType |
Test Method
|
| Pages |
52
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This test method2 covers the determination of fatigue crack growth rates from near-threshold (see region I in Fig. 1) to Kmax controlled instability (see region III in Fig. 1.) Results are expressed in terms of the crack-tip stress-intensity factor range (ΔK), defined by the theory of linear elasticity.
1.9Special requirements for the various specimen configurations appear in the following order:
| The Compact Specimen | Annex A1 |
| The Middle Tension Specimen | Annex A2 |
| The Eccentrically-Loaded Single Edge Crack Tension Specimen | Annex A3 |
1.10This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.11This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM E 2472 : 2012 : R2018 : EDT 3 | Standard Test Method for Determination of Resistance to Stable Crack Extension under Low-Constraint Conditions |
| ASTM E 2899 : 2024 | Standard Test Method for Measurement of Initiation Toughness in Surface Cracks Under Tension and Bending |
| ASTM E 1457 : 2023 : EDT 1 | Standard Test Method for Measurement of Creep Crack Growth Times in Metals |
| ASTM E 1681 : 2023 : EDT 1 | Standard Test Method for Determining Threshold Stress Intensity Factor for Environment-Assisted Cracking of Metallic Materials |
| ASTM E 2760 : 2019 : EDT 2 | Standard Test Method for Creep-Fatigue Crack Growth Testing |
| ASTM E 2760 : 2019 : EDT 1 | Standard Test Method for Creep-Fatigue Crack Growth Testing |
| ASTM F 3184 : 2016 : R2023 | Standard Specification for Additive Manufacturing Stainless Steel Alloy (UNS S31603) with Powder Bed Fusion |
| ASTM F 2565 : 2021 | Standard Guide for Extensively Irradiation-Crosslinked Ultra-High Molecular Weight Polyethylene Fabricated Forms for Surgical Implant Applications |
| ASTM E 1457 : 2023 | Standard Test Method for Measurement of Creep Crack Growth Times in Metals |
| ASTM E 399 : 2023 | Standard Test Method for Linear-Elastic Plane-Strain Fracture Toughness of Metallic Materials |
| ASTM E 2899 : 2019 : EDT 1 | Standard Test Method for Measurement of Initiation Toughness in Surface Cracks Under Tension and Bending |
| ASTM F 3055 : 2014 : REV A : R2021 | Standard Specification for Additive Manufacturing Nickel Alloy (UNS N07718) with Powder Bed Fusion |
| ASTM F 3056 : 2014 : R2021 | Standard Specification for Additive Manufacturing Nickel Alloy (UNS N06625) with Powder Bed Fusion |
| ASTM F 2924 : 2014 : R2021 | Standard Specification for Additive Manufacturing Titanium-6 Aluminum-4 Vanadium with Powder Bed Fusion |
| ASTM E 2714 : 2013 : R2020 | Standard Test Method for Creep-Fatigue Testing |
| ASTM F 3607 : 2022 | Standard Specification for Additive Manufacturing – Finished Part Properties – Maraging Steel via Powder Bed Fusion |
| ASTM G 129 : 2021 | Standard Practice for Slow Strain Rate Testing to Evaluate the Susceptibility of Metallic Materials to Environmentally Assisted Cracking |
| ASTM F 2759 : 2019 | Standard Guide for Assessment of the Ultra-High Molecular Weight Polyethylene (UHMWPE) Used in Orthopedic and Spinal Devices |
| ASTM E 1681 : 2023 | Standard Test Method for Determining Threshold Stress Intensity Factor for Environment-Assisted Cracking of Metallic Materials |
| ASTM F 3122 : 2014 : R2022 | Standard Guide for Evaluating Mechanical Properties of Metal Materials Made via Additive Manufacturing Processes |
| ASTM G 107 : 1995 : R2020 : EDT 1 | Standard Guide for Formats for Collection and Compilation of Corrosion Data for Metals for Computerized Database Input |
| ASTM F 3439 : 2022 | Additive manufacturing of metals — Finished part properties — Orientation and location dependence of mechanical properties for metal powder bed fusion |
| ASTM F 3302 : 2018 | Standard for Additive Manufacturing – Finished Part Properties – Standard Specification for Titanium Alloys via Powder Bed Fusion |
| ASTM F 3213 : 2017 | Standard for Additive Manufacturing – Finished Part Properties – Standard Specification for Cobalt-28 Chromium-6 Molybdenum via Powder Bed Fusion |
| ASTM E 2472 : 2012 : R2018 : EDT 2 | Standard Test Method for Determination of Resistance to Stable Crack Extension under Low-Constraint Conditions |
| ASTM F 3318 : 2018 | Standard for Additive Manufacturing – Finished Part Properties – Specification for AlSi10Mg with Powder Bed Fusion – Laser Beam |
| ASTM E 1820 : 2023 : REV B | Standard Test Method for Measurement of Fracture Toughness |
| ASTM E 8/E8M : 2024 | Standard Test Methods for Tension Testing of Metallic Materials |
| ASTM E 1823 : 2024 : REV A | Standard Terminology Relating to Fatigue and Fracture Testing |
| ASTM E 1820 : 2024 | Standard Test Method for Measurement of Fracture Toughness |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.