ASTM E 536 : 2016 : REDLINE
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Methods for Chemical Analysis of Zinc and Zinc Alloys
07-12-2023
English
04-01-2016
Important note : All end users must be registered with an Account prior to user licenses being assigned.CONTAINED IN VOL. 03.05, 2016 Describes the chemical analysis of zinc and zinc alloys having chemical compositions.
| Committee |
E 01
|
| DevelopmentNote |
Supersedes ASTM E 40 (12/2001)
|
| DocumentType |
Redline
|
| Pages |
6
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1These test methods cover the chemical analysis of zinc and zinc alloys having chemical compositions within the limits of Table 1.
1.2The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.3These test methods appear as follows:
| Sections | |
| Aluminum by the EDTA Titrimetric Method (0.5 to 4.5 %) | 10 – 17 |
| Aluminum, Cadmium, Copper, Iron, Lead, and Magnesium | 18 – 28 |
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in Section 6.
| ASTM F 1182 : 2007 : R2013 | Standard Specification for Anodes, Sacrificial Zinc Alloy |
| ASTM F 1182 : 2007 | Standard Specification for Anodes, Sacrificial Zinc Alloy |
| ASTM B 816 : 2000 : R2015 | Standard Specification for Coatings of Cadmium-Zinc Mechanically Deposited |
| ASTM B 240 : 2017 : REDLINE | Standard Specification for Zinc and Zinc-Aluminum (ZA) Alloys in Ingot Form for Foundry and Die Castings |
| ASTM B 791 : 1997 | Specification for Zinc-Aluminum (ZA) Alloy Foundry Die Castings (Withdrawn 1999) |
| ASTM B 894 : 2017 : REDLINE | Standard Specification for ACuZinc5 |
| ASTM B 669 : 1997 | Specification for Zinc-Aluminum (ZA) Alloys in Ingot Form for Foundry and Die Castings (Withdrawn 1999) |
| ASTM B 793 : 2016 : REDLINE | Standard Specification for Zinc Casting Alloy Ingot for Sheet Metal Forming Dies and Plastic Injection Molds |
| ASTM B 69 : 2016 : REDLINE | Standard Specification for Rolled Zinc |
| ASTM B 997 : 2016 : REDLINE | Standard Specification for Zinc-Aluminum Alloys in Ingot Form for Hot-Dip Coatings |
| BS EN 62321-5:2014 | Determination of certain substances in electrotechnical products Cadmium, lead and chromium in polymers and electronics and cadmium and lead in metals by AAS, AFS, ICP-OES and ICP-MS |
| MIL A 18001 : K | ANODES, SACRIFICIAL ZINC ALLOY |
| ASTM B 327 : 2016 : REDLINE | Standard Specification for Master Alloys Used in Making Zinc Die Casting Alloys |
| ASTM B 852 : 2016 : REDLINE | Standard Specification for Continuous Galvanizing Grade (CGG) Zinc Alloys for Hot-Dip Galvanizing of Sheet Steel |
| ASTM A 797 : 1982 | Specification for Aluminum-Zinc Alloy-Coated Steel Overhead Ground Wire Strand (Withdrawn 1988) |
| ASTM A 817 : 2012 : R2017 | Standard Specification for Metallic-Coated Steel Wire for Chain-Link Fence Fabric and Marcelled Tension Wire |
| ASTM B 816 : 2000 | Standard Specification for Coatings of Cadmium-Zinc Mechanically Deposited |
| ASTM B 792 : 2016 : REDLINE | Standard Specification for Zinc Alloys in Ingot Form for Slush Casting |
| ASTM A 817 : 2012 | Standard Specification for Metallic-Coated Steel Wire for Chain-Link Fence Fabric and Marcelled Tension Wire |
| MIL-Z-12061 Revision B:1983 | ZINC CARBONATE, BASIC, TECHNICAL |
| SAE AMS I 7068 : 2011 | INGOT, ZINC ALLOY (FOR SHEET METAL FORMING DIES) |
| ASTM F 3160 : 2016 | Standard Guide for Metallurgical Characterization of Absorbable Metallic Materials for Medical Implants |
| ASTM B 907 : 2016 : REDLINE | Standard Specification for Zinc, Tin and Cadmium Base Alloys Used as Solders |
| ASTM B 816 : 2000 : R2009 | Standard Specification for Coatings of Cadmium-Zinc Mechanically Deposited |
| MIL-DTL-18001 Revision L:2013 | ANODES, SACRIFICIAL ZINC ALLOY |
| SAE AMS 4803 : 2010 | ZINC ALLOY CASTINGS, DIE, 4.0AL - 0.04MG (AG40A), AS CAST |
| ASTM B 833 : 2013 : REDLINE | Standard Specification for Zinc and Zinc Alloy Wire for Thermal Spraying (Metallizing) for the Corrosion Protection of Steel |
| AWS C2.25/C2.25M : 2012 | SPECIFICATION FOR THERMAL SPRAY FEEDSTOCK - WIRE AND RODS |
| I.S. EN 62321-5:2014 | DETERMINATION OF CERTAIN SUBSTANCES IN ELECTROTECHNICAL PRODUCTS - PART 5: CADMIUM, LEAD AND CHROMIUM IN POLYMERS AND ELECTRONICS AND CADMIUM AND LEAD IN METALS BY AAS, AFS, ICP-OES AND ICP-MS |
| ASTM E 40 : 1988 | Standard Test Method for Chemical Analysis of Slab Zinc (Spelter) (Withdrawn 1993) |
| ASTM B 989 : 2014 | Standard Specification for High Fluidity (HF) Zinc-Aluminum Alloy in Ingot Form for Thin Wall Die Castings |
| ASTM E 47 : 1993 | Standard Test Methods for Chemical Analysis of Zinc Die-Casting Alloys (Withdrawn 1997) |
| ASTM B 816 : 2000 : R2004 : EDT 1 | Standard Specification for Coatings of Cadmium-Zinc Mechanically Deposited |
| ASTM B 892 : 2010 | Standard Specification for ACuZinc5 (Zinc-Copper-Aluminum) Alloy in Ingot Form for Die Castings |
| ASTM B 943 : 2016 : REDLINE | Standard Specification for Zinc and Tin Alloy Wire Used in Thermal Spraying for Electronic Applications |
| ASTM B 892 : 2010 : R2015 | Standard Specification for ACuZinc5 (Withdrawn 2022) |
| EN 62321-5:2014 | Determination of certain substances in electrotechnical products - Part 5: Cadmium, lead and chromium in polymers and electronics and cadmium and lead in metals by AAS, AFS, ICP-OES and ICP-MS |
| ASTM E 50 : 2017 : REDLINE | Standard Practices for Apparatus, Reagents, and Safety Considerations for Chemical Analysis of Metals, Ores, and Related Materials |
| ASTM E 1601 : 2012 : REDLINE | Standard Practice for Conducting an Interlaboratory Study to Evaluate the Performance of an Analytical Method |
| ASTM E 173 : 1993 | Practice for Conducting Interlaboratory Studies of Methods for Chemical Analysis of Metals (Withdrawn 1997) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.