ASTM E 2352 : 2004 : R2010
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Practice for Aerospace Cleanrooms and Associated Controlled Environments-Cleanroom Operations
Hardcopy , PDF
07-02-2019
English
04-01-2010
Important note : All end users must be registered with an Account prior to user licenses being assigned.This practice specifies basic requirements, procedures, and practices for operating aerospace cleanrooms and controlled environments and precautions associated with the facility and equipment used.
| Committee |
E 21
|
| DocumentType |
Standard Practice
|
| Pages |
14
|
| ProductNote |
Reconfirmed 2010
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1 This practice specifies basic requirements, procedures, and practices for operating aerospace cleanrooms and controlled environments and precautions associated with the facility and equipment used.
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| ASTM E 2042/E2042M : 2009 : R2016 | Standard Practice for Cleaning and Maintaining Controlled Areas and Clean Rooms |
| IEC 61025:2006 | Fault tree analysis (FTA) |
| ASTM F 318 : 2006 | Standard Practice for Sampling Airborne Particulate Contamination in Cleanrooms for Handling Aerospace Fluids |
| ASTM E 2217 : 2012 : REDLINE | Standard Practice for Design and Construction of Aerospace Cleanrooms and Contamination Controlled Areas |
| IEC 60812:2006 | Analysis techniques for system reliability - Procedure for failure mode and effects analysis (FMEA) |
| ISO 9237:1995 | Textiles — Determination of the permeability of fabrics to air |
| NASA STD 6001 : 2011 | FLAMMABILITY, OFFGASSING, AND COMPATIBILITY REQUIREMENTS AND TEST PROCEDURES |
| IEST RP CC016.2 : 2002(R2006) | THE RATE OF DEPOSITION OF NONVOLATILE RESIDUE IN CLEANROOMS |
| ISO 14644-2:2015 | Cleanrooms and associated controlled environments Part 2: Monitoring to provide evidence of cleanroom performance related to air cleanliness by particle concentration |
| EN 1149-1:2006 | Protective clothing - Electrostatic properties - Part 1: Test method for measurement of surface resistivity |
| ASTM E 595 : 2015 : REDLINE | Standard Test Method for Total Mass Loss and Collected Volatile Condensable Materials from Outgassing in a Vacuum Environment |
| FED-STD-209 Revision E:1992 | AIRBORNE PARTICULATE CLEANLINESS CLASSES IN CLEANROOMS AND CLEAN ZONES |
| IEST RP CC022.2 : 2004(R2008) | ELECTROSTATIC CHARGE IN CLEANROOMS AND OTHER CONTROLLED ENVIRONMENTS |
| ASTM E 1235 : 2012 : REDLINE | Standard Test Method for Gravimetric Determination of Nonvolatile Residue (NVR) in Environmentally Controlled Areas for Spacecraft |
| ISO 11092:2014 | Textiles — Physiological effects — Measurement of thermal and water-vapour resistance under steady-state conditions (sweating guarded-hotplate test) |
| ISO 14644-1:2015 | Cleanrooms and associated controlled environments Part 1: Classification of air cleanliness by particle concentration |
| ISO 7730:2005 | Ergonomics of the thermal environment — Analytical determination and interpretation of thermal comfort using calculation of the PMV and PPD indices and local thermal comfort criteria |
| ISO 14644-4:2001 | Cleanrooms and associated controlled environments — Part 4: Design, construction and start-up |
| ASTM E 2042 : 2004 | Standard Practice for Cleaning and Maintaining Controlled Areas and Clean Rooms |
| ASTM F 25 : 2004 | Standard Test Method for Sizing and Counting Airborne Particulate Contamination in Cleanrooms and Other Dust-Controlled Areas |
| IEST RP CC026.1 : 1995 | CLEANROOM OPERATIONS |
| ASTM E 1234 : 2012 : REDLINE | Standard Practice for Handling, Transporting, and Installing Nonvolatile Residue (NVR) Sample Plates Used in Environmentally Controlled Areas for Spacecraft |
| ASTM D 737 : 2004 | Test Method for Air Permeability of Textile Fabrics |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.