ASTM E 2002 : 2015 : REDLINE
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Practice for Determining Total Image Unsharpness and Basic Spatial Resolution in Radiography and Radioscopy
04-29-2022
English
10-13-2015
Important note : All end users must be registered with an Account prior to user licenses being assigned.CONTAINED IN VOL. 03.03, 2017 Defines the design and basic use of a gauge used to determine the total image unsharpness and the basic spatial resolution of film radiographs or of digital images taken with CR imaging plates, digital detector arrays, or radioscopic systems.
| Committee |
E 07
|
| DocumentType |
Redline
|
| Pages |
7
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy |
1.1This practice covers the design and basic use of a gauge used to determine the total image unsharpness and the basic spatial resolution of film radiographs or of digital images taken with CR imaging plates, digital detector arrays, or radioscopic systems.
1.2This practice is applicable to radiographic and radioscopic imaging systems utilizing X-ray and gamma ray radiation sources.
1.3The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.4The gauge described can be used effectively with tube voltages up to 600 kV. When using source voltages in the megavolt range the results may not be completely satisfactory.
1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| I.S. EN 12681-2:2017 | FOUNDING - RADIOGRAPHIC TESTING - PART 2: TECHNIQUES WITH DIGITAL DETECTORS |
| ASTM E 1165 : 2012 : R2017 | Standard Test Method for Measurement of Focal Spots of Industrial X-Ray Tubes by Pinhole Imaging |
| ASTM E 2698 : 2010 | Standard Practice for Radiological Examination Using Digital Detector Arrays |
| PREN 12679 : DRAFT 2017 | NON DESTRUCTIVE TESTING - DETERMINATION OF THE SIZE OF INDUSTRIAL RADIOGRAPHIC SOURCES - RADIOGRAPHIC METHOD |
| EN ISO 16371-2:2017 | Non-destructive testing - Industrial computed radiography with storage phosphor imaging plates - Part 2: General principles for testing of metallic materials using X-rays and gamma rays (ISO 16371-2:2017, Corrected version 2018-05) |
| ISO 16371-2:2017 | Non-destructive testing — Industrial computed radiography with storage phosphor imaging plates — Part 2: General principles for testing of metallic materials using X-rays and gamma rays |
| ASTM E 2007 : 2010 : R2016 | Standard Guide for Computed Radiography |
| 18/30368085 DC : 0 | BS EN 12679 - NON DESTRUCTIVE TESTING - DETERMINATION OF THE SIZE OF INDUSTRIAL RADIOGRAPHIC SOURCES - RADIOGRAPHIC METHOD |
| ASTM E 2869 : 2017 : REDLINE | Standard Digital Reference Images for Magnesium Castings |
| ASTM E 1000 : 2016 : REDLINE | Standard Guide for Radioscopy |
| ASTM E 2737 : 2010 | Standard Practice for Digital Detector Array Performance Evaluation and Long-Term Stability |
| ASTM E 1647 : 2016 : REDLINE | Standard Practice for Determining Contrast Sensitivity in Radiology |
| ASTM E 2445/E2445M : 2014 : REDLINE | Standard Practice for Performance Evaluation and Long-Term Stability of Computed Radiography Systems |
| EN 12681-2:2017 | Founding - Radiographic testing - Part 2: Techniques with digital detectors |
| I.S. EN ISO 16371-2:2017 | NON-DESTRUCTIVE TESTING - INDUSTRIAL COMPUTED RADIOGRAPHY WITH STORAGE PHOSPHOR IMAGING PLATES - PART 2: GENERAL PRINCIPLES FOR TESTING OF METALLIC MATERIALS USING X-RAYS AND GAMMA RAYS (ISO 16371-2:2017) |
| ASTM E 2736 : 2017 : REDLINE | Standard Guide for Digital Detector Array Radiography |
| ASTM E 2445 : 2005 | Standard Practice for Qualification and Long-Term Stability of Computed Radiology Systems |
| 17/30358413 DC : 0 | BS EN ISO 19232-5 - NON-DESTRUCTIVE TESTING - IMAGE QUALITY OF RADIOGRAPHS - PART 5: DETERMINATION OF THE IMAGE UNSHARPNESS AND BASIC SPATIAL RESOLUTION VALUE USING DUPLEX WIRE-TYPE IMAGE QUALITY INDICATORS |
| ASTM E 2445 : 2005 : R2010 | Standard Practice for Qualification and Long-Term Stability of Computed Radiology Systems |
| ASTM E 2422 : 2017 : REDLINE | Standard Digital Reference Images for Inspection of Aluminum Castings |
| ASTM E 1411 : 2016 : REDLINE | Standard Practice for Qualification of Radioscopic Systems |
| ASTM E 2597 : 2007 | Standard Practice for Manufacturing Characterization of Digital Detector Arrays |
| ASTM E 1165:2012 | Standard Test Method for Measurement of Focal Spots of Industrial X-Ray Tubes by Pinhole Imaging |
| ASTM E 2737 : 2010 : R2018 | Standard Practice for Digital Detector Array Performance Evaluation and Long-Term Stability |
| ASTM E 2597 : 2007 : EDT 1 | Standard Practice for Manufacturing Characterization of Digital Detector Arrays |
| BS EN 12681-2:2017 | Founding. Radiographic testing Techniques with digital detectors |
| BS EN ISO 16371-2:2017 | Non-destructive testing. Industrial computed radiography with storage phosphor imaging plates General principles for testing of metallic materials using X-rays and gamma rays |
| ASTM E 746 : 2018 : REDLINE | Standard Practice for Determining Relative Image Quality Response of Industrial Radiographic Imaging Systems |
| ASTM E 2597/E2597M : 2014 : REDLINE | Standard Practice for Manufacturing Characterization of Digital Detector Arrays |
| ASTM E 2660 : 2017 : REDLINE | Standard Digital Reference Images for Investment Steel Castings for Aerospace Applications |
| ASTM E 2868 : 2017 : REDLINE | Standard Digital Reference Images for Steel Castings up to 2 in. (50.8 mm) in Thickness |
| ASTM E 2973 : 2015 | Standard Digital Reference Images for Inspection of Aluminum and Magnesium Die Castings |
| ASTM E 1255 : 2016 : REDLINE | Standard Practice for Radioscopy |
| ASTM E 2007 : 2010 | Standard Guide for Computed Radiography |
| ASTM E 2903 : 2018 : REDLINE | Standard Test Method for Measurement of the Effective Focal Spot Size of Mini and Micro Focus X-ray Tubes |
| ASTM E 2446 : 2016 : REDLINE | Standard Practice for Manufacturing Characterization of Computed Radiography Systems |
| ISO/IEC 17050-1:2004 | Conformity assessment Supplier's declaration of conformity Part 1: General requirements |
| ISO 19232-1:2013 | Non-destructive testing — Image quality of radiographs — Part 1: Determination of the image quality value using wire-type image quality indicators |
| ISO 19232-5:2013 | Non-destructive testing Image quality of radiographs Part 5: Determination of the image unsharpness value using duplex wire-type image quality indicators |
| ISO 19232-2:2013 | Non-destructive testing — Image quality of radiographs — Part 2: Determination of the image quality value using step/hole-type image quality indicators |
| EN 462-5:1996 | Non-destructive testing - Image quality of radiographs - Part 5: Image quality indicators (duplex wire type), determination of image unsharpness value |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.