ASTM E 1860 : 2013 : R2018
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Elapsed Time Calibration of Thermal Analyzers
Available format(s)
Hardcopy , PDF
Superseded date
08-21-2023
Superseded by
Language(s)
English
Published date
08-20-2018
Important note : All end users must be registered with an Account prior to user licenses being assigned.| Committee |
E 37
|
| DocumentType |
Test Method
|
| Pages |
3
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This test method describes the calibration or performance confirmation of the elapsed-time signal from thermal analyzers.
1.2The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.3 There is no ISO standard equivalent to this test method.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM E 487 : 2020 | Standard Test Methods for Constant-Temperature Stability of Chemical Materials |
| ASTM E 537 : 2020 | Standard Test Method for Thermal Stability of Chemicals by Differential Scanning Calorimetry |
| ASTM E 2253 : 2021 | Standard Test Method for Temperature and Enthalpy Measurement Validation of Differential Scanning Calorimeters |
| ASTM E 2046 : 2019 | Standard Test Method for Reaction Induction Time by Thermal Analysis |
| ASTM E 2890 : 2021 | Standard Test Method for Determination of Kinetic Parameters and Reaction Order for Thermally Unstable Materials by Differential Scanning Calorimetry Using the Kissinger and Farjas Methods |
| ASTM E 1858 : 2023 | Standard Test Methods for Determining Oxidation Induction Time of Hydrocarbons by Differential Scanning Calorimetry |
| ASTM E 698 : 2023 | Standard Test Method for Kinetic Parameters for Thermally Unstable Materials Using Differential Scanning Calorimetry and the Flynn/Wall/Ozawa Method |
| ASTM E 2008 : 2017 : R2021 | Standard Test Methods for Volatility Rate by Thermogravimetry |
| ASTM E 698 : 2018 | Standard Test Method for Kinetic Parameters for Thermally Unstable Materials Using Differential Scanning Calorimetry and the Flynn/Wall/Ozawa Method |
| ASTM E 1858 : 2008 : R2015 : EDT 1 | Standard Test Methods for Determining Oxidation Induction Time of Hydrocarbons by Differential Scanning Calorimetry |
| ASTM E 1868 : 2010 : R2015 | Standard Test Methods for Loss-On-Drying by Thermogravimetry |
| ASTM E 793 : 2006 : R2018 | Standard Test Method for Enthalpies of Fusion and Crystallization by Differential Scanning Calorimetry |
| ASTM E 2160 : 2004 : R2018 | Standard Test Method for Heat of Reaction of Thermally Reactive Materials by Differential Scanning Calorimetry |
| ASTM E 2008 : 2017 | Standard Test Methods for Volatility Rate by Thermogravimetry |
| ASTM E 2046 : 2014 | Standard Test Method for Reaction Induction Time by Thermal Analysis |
| ASTM E 2253 : 2016 | Standard Test Method for Temperature and Enthalpy Measurement Validation of Differential Scanning Calorimeters |
| ASTM E 487 : 2014 | Standard Test Method for Constant-Temperature Stability of Chemical Materials |
| ASTM E 537 : 2012 | Standard Test Method for The Thermal Stability of Chemicals by Differential Scanning Calorimetry |
| ASTM E 2890 : 2012 : R2018 | Standard Test Method for Kinetic Parameters for Thermally Unstable Materials by Differential Scanning Calorimetry Using the Kissinger Method |
| ASTM E 1142 : 2022 | Standard Terminology Relating to Thermophysical Properties |
| ASTM E 473 : 2022 : REV D | Standard Terminology Relating to Thermal Analysis and Rheology |
| ASTM D 3895 : 1998 | Standard Test Method for Oxidative-Induction Time of Polyolefins by Differential Scanning Calorimetry |
| ASTM E 2161 : 2023 | Standard Terminology Relating to Performance Validation in Thermal Analysis and Rheology |
| ASTM E 473 : 2022 | Standard Terminology Relating to Thermal Analysis and Rheology |
| ASTM E 2161 : 2015 | Standard Terminology Relating to Performance Validation in Thermal Analysis and Rheology |
| ASTM E 1142 : 1997 | Standard Terminology Relating to Thermophysical Properties |
| ASTM E 473 : 2021 | Standard Terminology Relating to Thermal Analysis and Rheology |
| ASTM E 1858 : 1997 | Standard Test Method for Determining Oxidation Induction Time of Hydrocarbons by Differential Scanning Calirometry |
| ASTM E 2161 : 2022 : REV B | Standard Terminology Relating to Performance Validation in Thermal Analysis and Rheology |
| ASTM D 3350 : 2000 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
| ASTM D 5483 : 2021 | Standard Test Method for Oxidation Induction Time of Lubricating Greases by Pressure Differential Scanning Calorimetry |
| ASTM E 1142 : 2022 : REV A | Standard Terminology Relating to Thermophysical Properties |
| ASTM E 1142 : 2022 : REV C | Standard Terminology Relating to Thermophysical Properties |
| ASTM E 473 : 2022 : REV B | Standard Terminology Relating to Thermal Analysis and Rheology |
| ASTM D 3350 : 2021 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
| ASTM E 473 : 2018 | Standard Terminology Relating to Thermal Analysis and Rheology |
| ASTM E 691 : 2020 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM E 1142 : 2015 : R2020 | Standard Terminology Relating to Thermophysical Properties |
| ASTM E 1868 : 2010 : R2021 | Standard Test Methods for Loss-On-Drying by Thermogravimetry |
| ASTM E 2161 : 2021 : REV A | Standard Terminology Relating to Performance Validation in Thermal Analysis and Rheology |
| ASTM E 2161 : 2022 | Standard Terminology Relating to Performance Validation in Thermal Analysis and Rheology |
| ASTM E 1142 : 2021 : REV A | Standard Terminology Relating to Thermophysical Properties |
| ASTM D 3350 : 2014 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
| ASTM D 5483 : 2020 | Standard Test Method for Oxidation Induction Time of Lubricating Greases by Pressure Differential Scanning Calorimetry |
| ASTM E 1868 : 1997 | Standard Test Method for Loss-On-Drying by Thermogravimetry |
| ASTM E 473 : 2023 : REV A | Standard Terminology Relating to Thermal Analysis and Rheology |
| ASTM E 2161 : 2001 | Standard Terminology Relating to Performance Validation in Thermal Analysis |
| ASTM E 2161 : 2022 : REV A | Standard Terminology Relating to Performance Validation in Thermal Analysis and Rheology |
| ASTM E 691 : 2019 : EDT 1 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM E 473 : 2022 : REV C | Standard Terminology Relating to Thermal Analysis and Rheology |
| ASTM E 691 : 2023 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM E 2070 : 2000 | Standard Test Method for Kinetic Parameters by Differential Scanning Calorimetry Using Isothermal Methods |
| ASTM E 2161 : 2023 : REV A | Standard Terminology Relating to Performance Validation in Thermal Analysis and Rheology |
| ASTM E 691 : 2022 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM E 691 : 2009 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM E 2161 : 2021 | Standard Terminology Relating to Performance Validation in Thermal Analysis and Rheology |
| ASTM E 2161 : 2023 : REV B | Standard Terminology Relating to Performance Validation in Thermal Analysis and Rheology |
| ASTM D 4565 : 1990 | Standard Test Methods for Physical and Enviormental Performance Properties of Insulations and Jackets for Telecommunications Wire and Cable |
| ASTM E 2161 : 2021 : REV B | Standard Terminology Relating to Performance Validation in Thermal Analysis and Rheology |
| ASTM E 691 : 2021 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM E 1142 : 2022 : REV B | Standard Terminology Relating to Thermophysical Properties |
| ASTM E 1142 : 2023 | Standard Terminology Relating to Thermophysical Properties |
| ASTM E 473 : 2021 : REV A | Standard Terminology Relating to Thermal Analysis and Rheology |
| ASTM E 1858 : 2023 | Standard Test Methods for Determining Oxidation Induction Time of Hydrocarbons by Differential Scanning Calorimetry |
| ASTM E 473 : 2022 : REV A | Standard Terminology Relating to Thermal Analysis and Rheology |
| ASTM E 473 : 2023 | Standard Terminology Relating to Thermal Analysis and Rheology |
| ASTM D 5483 : 2005 : R2015 | Standard Test Method for Oxidation Induction Time of Lubricating Greases by Pressure Differential Scanning Calorimetry |
| ASTM E 2070 : 2013 : R2018 | Standard Test Methods for Kinetic Parameters by Differential Scanning Calorimetry Using Isothermal Methods |
| ASTM E 1142 : 2021 | Standard Terminology Relating to Thermophysical Properties |
| ASTM D 5483 : 1995 | Standard Test Method for Oxidation Induction Time of Lubricating Greases by Pressure Differential Scanning Calorimetry |
| ASTM E 1142 : 2023 : REV A | Standard Terminology Relating to Thermophysical Properties |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.