ASTM E 168 : 2016
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Practices for General Techniques of Infrared Quantitative Analysis
Available format(s)
Hardcopy , PDF
Superseded date
01-13-2023
Superseded by
Language(s)
English
Published date
06-07-2016
Important note : All end users must be registered with an Account prior to user licenses being assigned.CONTAINED IN VOL. 03.06, 2016 Defines the techniques most often used in infrared quantitative analysis.
| Committee |
E 13
|
| DocumentType |
Standard Practice
|
| Pages |
18
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1These practices cover the techniques most often used in infrared quantitative analysis. Practices associated with the collection and analysis of data on a computer are included as well as practices that do not use a computer.
1.2This practice does not purport to address all of the concerns associated with developing a new quantitative method. It is the responsibility of the developer to ensure that the results of the method fall in the desired range of precision and bias.
1.3The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific hazard statements appear in Section 6, Note A4.7, Note A4.11, and Note A5.6.
| ASTM E 1944 : 1998 : R2013 | Standard Practice for Describing and Measuring Performance of Laboratory Fourier Transform Near-Infrared (FT-NIR) Spectrometers: Level Zero and Level One Tests |
| CSA S807 : 2010 | SPECIFICATION FOR FIBRE-REINFORCED POLYMERS |
| ASTM D 3133 : 2001 | Standard Test Method for Quantitative Determination of Cellulose Nitrate in Alkyd Modified Lacquers by Infrared Spectrophotometry |
| ASTM E 169 : 2016 : REDLINE | Standard Practices for General Techniques of Ultraviolet-Visible Quantitative Analysis |
| ASTM E 60 : 2011 | Standard Practice for Analysis of Metals, Ores, and Related Materials by Spectrophotometry |
| MIL-A-27420 Base Document:1970 | AIR, LIQUID, FOR BREATHING PURPOSES |
| ASTM E 131 : 2010 : R2015 | Standard Terminology Relating to Molecular Spectroscopy |
| BS ISO 15063:2011 | Plastics. Polyols for use in the production of polyurethanes. Determination of hydroxyl number by NIR spectroscopy |
| ASTM D 2124 : 1999 : R2011 | Standard Test Method for Analysis of Components in Poly(Vinyl Chloride) Compounds Using an Infrared Spectrophotometric Technique (Withdrawn 2020) |
| MIL PRF 002104 : L | LUBRICATING OIL, INTERNAL COMBUSTION ENGINE, COMBAT/TACTICAL SERVICE |
| ASTM E 2412 : 2010 | Standard Practice for Condition Monitoring of Used Lubricants by Trend Analysis Using Fourier Transform Infrared (FT-IR) Spectrometry |
| ASTM D 3921 : 1996 : R2011 | Standard Test Method for Oil and Grease and Petroleum Hydrocarbons in Water (Withdrawn 2013) |
| MIL-PRF-32177 Revision A:2012 | CLEANING COMPOUND, NONSKID |
| ASTM D 7678 : 2017 : REDLINE | Standard Test Method for Total Oil and Grease (TOG) and Total Petroleum Hydrocarbons (TPH) in Water and Wastewater with Solvent Extraction using Mid-IR Laser Spectroscopy |
| ASTM E 1944 : 1998 : R2002 | Standard Practice for Describing and Measuring Performance of Laboratory Fourier Transform Near-Infrared (FT-NIR) Spectrometers: Level Zero and Level One Tests |
| ASTM E 2106 : 2000 : R2011 | Standard Practice for General Techniques of Liquid Chromatography-Infrared (LC/IR) and Size Exclusion Chromatography-Infrared (SEC/IR) Analyses |
| SAE AMS 3961/3 : 2015 | 350 DEGREES F AUTOCLAVE CURE, LOW FLOW TOUGHENED EPOXY PREPREGS, TYPE 35, CLASS 1, GRADE 190, FIBER 1 |
| ASTM D 5594 : 1998 : R2004 | Standard Test Method for Determination of the Vinyl Acetate Content of Ethylene-Vinyl Acetate (EVA) Copolymers by Fourier Transform Infrared Spectroscopy (FT-IR) |
| ASTM D 7418 : 2012 : REDLINE | Standard Practice for Set-Up and Operation of Fourier Transform Infrared (FT-IR) Spectrometers for In-Service Oil Condition Monitoring |
| ASTM E 1865 : 1997 : R2007 | Standard Guide for Open-Path Fourier Transform Infrared (OP/FT-IR) Monitoring of Gases and Vapors in Air |
| ASTM E 932 : 1989 : R2007 | Standard Practice for Describing and Measuring Performance of Dispersive Infrared Spectrometers |
| ASTM E 1252 : 1998 | Standard Practice for General Techniques for Obtaining Infrared Spectra for Qualitative Analysis |
| ASTM D 6342 : 2012 : R2017 : EDT 1 | Standard Practice for Polyurethane Raw Materials: Determining Hydroxyl Number of Polyols by Near Infrared (NIR) Spectroscopy |
| ASTM D 3089 : 1997 : R2008 | Standard Practice for Determining the A-D Dimension of Aerosol Valve Dip Tubes |
| ASTM E 3045 : 2016 | Standard Practice for Crack Detection Using Vibroacoustic Thermography |
| ASTM D 3594 : 1993 : R2000 | Standard Test Method for Copolymerized Ethyl Acrylate In Ethylene-Ethyl Acrylate Copolymers |
| ASTM D 7806 : 2012 | Standard Test Method for Determination of the Fatty Acid Methyl Ester (FAME) Content of a Blend of Biodiesel and Petroleum-Based Diesel Fuel Oil Using Mid-Infrared Spectroscopy |
| ASTM D 7588 : 2011 | Standard Guide for FT-IR Fingerprinting of a Non-Aqueous Liquid Paint as Supplied in the Manufacturer's Container |
| ASTM E 1865:1997 | Standard Guide for Open-Path Fourier Transform Infrared (OP/FT-IR) Monitoring of Gases and Vapors in Air |
| ASTM E 334 : 2001 : R2013 | Standard Practice for General Techniques of Infrared Microanalysis |
| ASTM F 1630 : 2000 | Standard Test Method for Low Temperature FT-IR Analysis of Single Crystal Silicon for III-V Impurities (Withdrawn 2003) |
| ASTM E 131 : 2010 | Standard Terminology Relating to Molecular Spectroscopy |
| ASTM D 5594 : 1998 | Standard Test Method for Determination of the Vinyl Acetate Content of Ethylene-Vinyl Acetate (EVA) Copolymers by Fourier Transform Infrared Spectroscopy (FT-IR) |
| ASTM E 1252 : 1998 : R2007 | Standard Practice for General Techniques for Obtaining Infrared Spectra for Qualitative Analysis |
| ASTM E 204 : 1998 | Standard Practices for Identification of Material by Infrared Absorption Spectroscopy, Using the ASTM Coded Band and Chemical Classification Index |
| ASTM D 5477 : 2011 | Standard Practice for Identification of Polymer Layers or Inclusions by Fourier Transform Infrared Microspectroscopy (FT-IR) |
| MIL-P-46144 Revision C:1986 | PLASTIC SHEET, POLYCARBONATE |
| MIL-C-47221 Revision A:1982 | COMPOUND, MOLDING, EPOXY RESIN, SILICON DIOXIDE AND ASBESTOS FIBER FILL |
| CSA S808 : 2014 | SPECIFICATION FOR FIBRE-REINFORCED POLYMER (FRP) MATERIALS FOR EXTERNALLY REINFORCING STRUCTURES |
| ASTM D 7575 : 2011 | Standard Test Method for Solvent-Free Membrane Recoverable Oil and Grease by Infrared Determination |
| ASTM D 2238 : 1992 : R1999 | Standard Test Methods for Absorbance of Polyethylene Due to Methyl Groups at 1378 cm |
| DWA-M 143-20:2018 | TEST METHOD FOR DROP IMPACT RESISTANCE OF BLOW-MOLDED THERMOPLASTIC CONTAINERS |
| ASTM E 334:2001 | Standard Practice for General Techniques of Infrared Microanalysis |
| CSA S807 : 2010 : R2015 | SPECIFICATION FOR FIBRE-REINFORCED POLYMERS |
| MIL-PRF-85570 Revision E:2012 | CLEANING COMPOUNDS, AIRCRAFT, EXTERIOR |
| ASTM D 2702 : 2005 : R2016 | Standard Practice for Rubber Chemicals—Determination of Infrared Absorption Characteristics |
| SAE AMS 3961/1 : 2015 | 350 DEGREES F AUTOCLAVE CURE, LOW FLOW TOUGHENED EPOXY PREPREGS, TYPE 38, CLASS 2, GRADE 193, STYLE 3K-70-PW, FIBER 1 |
| ASTM E 1865 : 1997 : R2013 | Standard Guide for Open-Path Fourier Transform Infrared (OP/FT-IR) Monitoring of Gases and Vapors in Air |
| ASTM D 2238 : 1992 : R2004 | Standard Test Methods for Absorbance of Polyethylene Due to Methyl Groups at 1378 cm |
| ASTM E 1642 : 2000 : R2005 | Standard Practice for General Techniques of Gas Chromatography Infrared (GC/IR) Analysis |
| ASTM D 8111 : 2017 | Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IIIH, Spark-Ignition Engine |
| ASTM E 2105 : 2000 : R2016 | Standard Practice for General Techniques of Thermogravimetric Analysis (TGA) Coupled With Infrared Analysis (TGA/IR) |
| ASTM E 573 : 2001 : R2013 | Standard Practices for Internal Reflection Spectroscopy |
| ASTM D 6342 : 20121 | Standard Practice for Polyurethane Raw Materials: Determining Hydroxyl Number of Polyols by Near Infrared (NIR) Spectroscopy |
| ASTM E 1944 : 1998 : R2007 | Standard Practice for Describing and Measuring Performance of Laboratory Fourier Transform Near-Infrared (FT-NIR) Spectrometers: Level Zero and Level One Tests |
| ASTM E 932 : 1989 : R2013 | Standard Practice for Describing and Measuring Performance of Dispersive Infrared Spectrometers |
| ASTM E 2106 : 2000 : R2006 | Standard Practice for General Techniques of Liquid Chromatography-Infrared (LC/IR) and Size Exclusion Chromatography-Infrared (SEC/IR) Analyses |
| ASTM D 3594 : 1993 : R2006 | Standard Test Method for Copolymerized Ethyl Acrylate In Ethylene-Ethyl Acrylate Copolymers |
| ASTM D 2124 : 1999 : R2004 | Standard Test Method for Analysis of Components in Poly(Vinyl Chloride) Compounds Using an Infrared Spectrophotometric Technique |
| ASTM D 2124 : 1999 : EDT 1 | Standard Test Method for Analysis of Components in Poly(Vinyl Chloride) Compounds Using an Infrared Spectrophotometric Technique |
| ASTM D 6277 : 2007 : R2012 | Standard Test Method for Determination of Benzene in Spark-Ignition Engine Fuels Using Mid Infrared Spectroscopy |
| ASTM D 7371 : 2014 : REDLINE | Standard Test Method for Determination of Biodiesel (Fatty Acid Methyl Esters) Content in Diesel Fuel Oil Using Mid Infrared Spectroscopy (FTIR-ATR-PLS Method) |
| ASTM E 2106:2000 | Standard Practice for General Techniques of Liquid Chromatography-Infrared (LC/IR) and Size Exclusion Chromatography-Infrared (SEC/IR) Analyses |
| ASTM F 561 : 2013 | Standard Practice for Retrieval and Analysis of Medical Devices, and Associated Tissues and Fluids |
| ASTM D 345 : 2002 | Side bearings of the freight wagon bogies. General specifications |
| ASTM F 1864 : 2021 | Standard Test Method for Dust Erosion Resistance of Optical and Infrared Transparent Materials and Coatings |
| ASTM D 6277 : 2007 : R2022 | Standard Test Method for Determination of Benzene in Spark-Ignition Engine Fuels Using Mid Infrared Spectroscopy |
| ASTM E 1865 : 1997 : R2021 | Standard Guide for Open-Path Fourier Transform Infrared (OP/FT-IR) Monitoring of Gases and Vapors in Air |
| ASTM D 3124 : 1998 : R2019 | Standard Test Method for Vinylidene Unsaturation in Polyethylene by Infrared Spectrophotometry |
| ASTM D 3288/D3288M : 2020 | Standard Test Methods for Magnet-Wire Enamels |
| ASTM E 2106 : 2000 : R2019 | Standard Practice for General Techniques of Liquid Chromatography-Infrared (LC/IR) and Size Exclusion Chromatography-Infrared (SEC/IR) Analyses |
| ASTM D 7806 : 2020 | Standard Test Method for Determination of Biodiesel (Fatty Acid Methyl Ester) and Triglyceride Content in Diesel Fuel Oil Using Mid-Infrared Spectroscopy (FTIR Transmission Method) |
| ASTM D 6348 : 2012 : R2020 | Standard Test Method for Determination of Gaseous Compounds by Extractive Direct Interface Fourier Transform Infrared (FTIR) Spectroscopy |
| ASTM E 573 : 2001 : R2021 | Standard Practices for Internal Reflection Spectroscopy |
| ASTM D 6047 : 2017 : R2021 | Standard Test Methods for Rubber, Raw—Determination of 5-Ethylidenenorbornene (ENB) or Dicyclopentadiene (DCPD) in Ethylene-Propylene-Diene (EPDM) Terpolymers |
| ASTM D 7399 : 2018 | Standard Test Method for Determination of the Amount of Polypropylene in Polypropylene/Low Density Polyethylene Mixtures Using Infrared Spectrophotometry |
| ASTM D 3677 : 2010 : R2019 | Standard Test Methods for Rubber—Identification by Infrared Spectrophotometry |
| ASTM E 1982 : 1998 : R2021 | Standard Practice for Open-Path Fourier Transform Infrared (OP/FT-IR) Monitoring of Gases and Vapors in Air |
| ASTM D 6645 : 2018 | Standard Test Method for Methyl (Comonomer) Content in Polyethylene by Infrared Spectrophotometry |
| ASTM D 7678 : 2017 : R2022 | Standard Test Method for Total Oil and Grease (TOG) and Total Petroleum Hydrocarbons (TPH) in Water and Wastewater with Solvent Extraction using Mid-IR Laser Spectroscopy |
| ASTM D 2238 : 2022 | Standard Test Methods for Absorbance of Polyethylene Due to Methyl Groups at 1378 cm<sup>−1</sup> |
| ASTM D 2144 : 2007 : R2021 | Standard Practices for Examination of Electrical Insulating Oils by Infrared Absorption |
| ASTM E 1944 : 1998 : R2021 | Standard Practice for Describing and Measuring Performance of Laboratory Fourier Transform Near-Infrared (FT-NIR) Spectrometers: Level Zero and Level One Tests |
| ASTM D 5576 : 2000 : R2021 : EDT 1 | Standard Practice for Determination of Structural Features in Polyolefins and Polyolefin Copolymers by Infrared Spectrophotometry (FT-IR) |
| ASTM D 7588 : 2011 : R2018 | Standard Guide for FT-IR Fingerprinting of a Non-Aqueous Liquid Paint as Supplied in the Manufacturer's Container |
| ASTM D 3900 : 2017 : R2021 | Standard Test Methods for Rubber—Determination of Ethylene Units in Ethylene-Propylene Copolymers (EPM) and in Ethylene-Propylene-Diene Terpolymers (EPDM) by Infrared Spectrometry |
| ASTM E 169 : 2016 : R2022 | Standard Practices for General Techniques of Ultraviolet-Visible Quantitative Analysis |
| ASTM D 6342 : 2022 | Standard Practice for Polyurethane Raw Materials: Determining Hydroxyl Number of Polyols by Near Infrared (NIR) Spectroscopy |
| ASTM D 2702 : 2005 : R2021 | Standard Practice for Rubber Chemicals—Determination of Infrared Absorption Characteristics |
| ASTM E 275 : 2008 : R2022 | Standard Practice for Describing and Measuring Performance of Ultraviolet and Visible Spectrophotometers |
| ASTM D 7418 : 2022 | Standard Practice for Set-Up and Operation of Fourier Transform Infrared (FT-IR) Spectrometers for In-Service Oil Condition Monitoring |
| ASTM E 60 : 2011 : R2022 : EDT 1 | Standard Practice for Analysis of Metals, Ores, and Related Materials by Spectrophotometry |
| ASTM E 3045 : 2022 | Standard Practice for Crack Detection Using Vibroacoustic Thermography |
| ASTM D 5594 : 2018 : REV A | Standard Test Method for Determination of the Vinyl Acetate Content of Ethylene-Vinyl Acetate (EVA) Copolymers by Fourier Transform Infrared Spectroscopy (FT-IR) |
| ASTM D 7861 : 2014 : R2019 | Standard Test Method for Determination of Fatty Acid Methyl Esters (FAME) in Diesel Fuel by Linear Variable Filter (LVF) Array Based Mid-Infrared Spectroscopy |
| ASTM D 7889 : 2021 | Standard Test Method for Field Determination of In-Service Fluid Properties Using IR Spectroscopy |
| ASTM D 5477 : 2018 | Standard Practice for Identification of Polymer Layers or Inclusions by Fourier Transform Infrared Microspectroscopy (FT-IR) |
| ASTM D 8350 : 2022 | Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IVB Spark-Ignition Engine |
| ASTM D 8074 : 2022 | Standard Test Method for Evaluation of Diesel Engine Oils in DD13 Diesel Engine |
| ASTM D 6248 : 2021 | Standard Test Method for Vinyl and Trans Unsaturation in Polyethylene by Infrared Spectrophotometry |
| ASTM D 8193 : 2018 | Standard Test Method for Total Oil and Grease (TOG) and Total Petroleum Hydrocarbon (TPH) in Water and Wastewater with Solvent Extraction Using Non-Dispersive Mid-IR Transmission Spectroscopy |
| ASTM D 7371 : 2014 : R2022 | Standard Test Method for Determination of Biodiesel (Fatty Acid Methyl Esters) Content in Diesel Fuel Oil Using Mid Infrared Spectroscopy (FTIR-ATR-PLS Method) |
| ASTM D 8111 : 2022 | Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IIIH, Spark-Ignition Engine |
| ASTM D 3594 : 1993 | Standard Test Method for Copolymerized Ethyl Acrylate In Ethylene-Ethyl Acrylate Copolymers |
| ASTM E 1982: 1998 | Standard Practice for Open-Path Fourier Transform Infrared (OP/FT-IR) Monitoring of Gases and Vapors in Air |
| ASTM E 2105 : 2000 : R2010 | Standard Practice for General Techniques of Thermogravimetric Analysis (TGA) Coupled With Infrared Analysis (TGA/IR) |
| MIL-P-48296 Base Document:1974 | POLYTETRAFLUOROETHYLENE (PTFE) |
| ASTM D 6645 : 2001 | Standard Test Method for Methyl (Comonomer) Content in Polyethylene by Infrared Spectrophotometry |
| ASTM E 1982 : 1998 : R2007 | Standard Practice for Open-Path Fourier Transform Infrared (OP/FT-IR) Monitoring of Gases and Vapors in Air |
| ASTM E 1865 : 1997 : R2002 | Standard Guide for Open-Path Fourier Transform Infrared (OP/FT-IR) Monitoring of Gases and Vapors in Air |
| ASTM D 7399 : 2008 | Standard Test Method for Determination of the Amount of Polypropylene (PP) in Polypropylene/LDPE Mixtures Using Infrared Spectrophotometer (FTIR) (Withdrawn 2017) |
| ASTM E 1982 : 1998 : R2013 | Standard Practice for Open-Path Fourier Transform Infrared (OP/FT-IR) Monitoring of Gases and Vapors in Air |
| ASTM D 3921 : 1996 | Standard Test Method for Oil and Grease and Petroleum Hydrocarbons in Water |
| ASTM D 2702 : 2005 | Standard Practice for Rubber Chemicals-Determination of Infrared Absorption Characteristics |
| ASTM D 2144 : 2007 : R2013 | Standard Practices for Examination of Electrical Insulating Oils by Infrared Absorption |
| ASTM F 121 : 1983 : EDT 1 | Test Method for Interstitial Atomic Oxygen Content of Silicon by Infrared Absorption (Withdrawn 1989) |
| ASTM D 3288 : 2003 | Standard Test Methods for Magnet-Wire Enamels |
| MIL D 48561 : A | |
| MIL-A-70604 Base Document:1988 | AMINE BONDING AGENT |
| ASTM D 3124 : 1998 : R2003 | Standard Test Method for Vinylidene Unsaturation in Polyethylene by Infrared Spectrophotometry |
| GOST R 52714:2018 | Motor gasolines. Determination of individual and group hydrocarbon composition by capillary gas сhromatography method |
| ASTM D 3414 : 1998 : R2011 : EDT 1 | Standard Test Method for Comparison of Waterborne Petroleum Oils by Infrared Spectroscopy (Withdrawn 2018) |
| ASTM D 3124 : 1998 | Standard Test Method for Vinylidene Unsaturation in Polyethylene by Infrared Spectrophotometry |
| SAE AMS 3961/2 : 2015 | 350 DEGREES F AUTOCLAVE CURE, LOW FLOW TOUGHENED EPOXY PREPREGS, TYPE 35, CLASS 1, GRADE 190, FIBER 2 |
| ASTM D 3133 : 2001 : R2005 | Standard Test Method for Quantitative Determination of Cellulose Nitrate in Alkyd Modified Lacquers by Infrared Spectrophotometry (Withdrawn 2008) |
| SAE AMS 3960 : 2015 | Advanced Composites Prepreg - Nominal 250 °F Cure - Carbon Fiber and Epoxy Resin, Unidirectional Tape |
| ASTM D 3414 : 1998 : R2004 | Standard Test Method for Comparison of Waterborne Petroleum Oils by Infrared Spectroscopy |
| ASTM E 1655 : 2017 : REDLINE | Standard Practices for Infrared Multivariate Quantitative Analysis |
| ASTM F 120 : 1988 | Practices for Determination of the Concentration of Impurities in Single Crystal Semiconductor Materials by Infrared Absorption Spectroscopy (Withdrawn 1993) |
| ASTM E 2105 : 2000 : R2005 | Standard Practice for General Techniques of Thermogravimetric Analysis (TGA) Coupled With Infrared Analysis (TGA/IR) |
| ASTM E 1642 : 2000 | Standard Practice for General Techniques of Gas Chromatography Infrared (GC/IR) Analysis |
| ASTM D 6277 : 2007 | Standard Test Method for Determination of Benzene in Spark-Ignition Engine Fuels Using Mid Infrared Spectroscopy |
| ASTM D 5576 : 2000 : R2013 | Standard Practice for Determination of Structural Features in Polyolefins and Polyolefin Copolymers by Infrared Spectrophotometry (FT-IR) |
| ASTM D 7861 : 2014 : EDT 1 | Standard Test Method for Determination of Fatty Acid Methyl Esters (FAME) in Diesel Fuel by Linear Variable Filter (LVF) Array Based Mid-Infrared Spectroscopy |
| ASTM D 7861 : 2014 | Standard Test Method for Determination of Fatty Acid Methyl Esters (FAME) in Diesel Fuel by Linear Variable Filter (LVF) Array Based Mid-Infrared Spectroscopy |
| ASTM E 204 : 1998 : R2007 | Standard Practices for Identification of Material by Infrared Absorption Spectroscopy, Using the ASTM Coded Band and Chemical Classification Index (Withdrawn 2014) |
| ASTM E 932 : 1989 : R2002 | Standard Practice for Describing and Measuring Performance of Dispersive Infrared Spectrometers |
| ASTM D 6248 : 1998 : R2012 : EDT 1 | Standard Test Method for Vinyl and Trans Unsaturation in Polyethylene by Infrared Spectrophotometry (Withdrawn 2021) |
| ASTM E 573 : 2001 | Standard Practices for Internal Reflection Spectroscopy |
| ASTM D 6248 : 1998 : R2004 | Standard Test Method for Vinyl and Trans Unsaturation in Polyethylene by Infrared Spectrophotometry |
| SAE AMS C 22587 : 1999 | CARTRIDGES, GREASE, 14 OUNCE (FOR CARTRIDGE-TYPE GREASE GUN) |
| MIL-M-48767 Base Document:1975 | Methyl Formate (For Use In Ammunition) |
| ASTM E 932 : 1989 : R1997 | Standard Practice for Describing and Measuring Performance of Dispersive Infrared Spectrometers |
| ASTM D 6248 : 1998 | Standard Test Method for Vinyl and Trans Unsaturation in Polyethylene by Infrared Spectrophotometry |
| MIL-E-48225 Base Document:1973 | ETHYLENE GLYCOL DINITRATE (EGDN) |
| ASTM D 5576:2000 | Standard Practice for Determination of Structural Features in Polyolefins and Polyolefin Copolymers by Infrared Spectroscopy (FT-IR) |
| ASTM D 3414 : 1998 | Standard Test Method for Comparison of Waterborne Petroleum Oils by Infrared Spectroscopy |
| ASTM E 1252 : 1998 : R2002 | Standard Practice for General Techniques for Obtaining Infrared Spectra for Qualitative Analysis |
| ADS-13F-HDBK : 1997 | AERONAUTICAL DESIGN STANDARD - HANDBOOK - AIR VEHICLE MATERIALS AND PROCESSES |
| ASTM D 5594 : 1998 : R2012 | Standard Test Method for Determination of the Vinyl Acetate Content of Ethylene-Vinyl Acetate (EVA) Copolymers by Fourier Transform Infrared Spectroscopy (FT-IR) |
| SAE AMS P 46144 : 2015 | PLASTIC SHEET, POLYCARBONATE |
| ASTM D 7066 : 2004 : R2017 | Standard Test Method for dimer/trimer of chlorotrifluoroethylene (S-316) Recoverable Oil and Grease and Nonpolar Material by Infrared Determination |
| ASTM D 7066 : 2004 : EDT 1 | Standard Test Method for dimer/trimer of chlorotrifluoroethylene (S-316) Recoverable Oil and Grease and Nonpolar Material by Infrared Determination |
| ASTM E 1642 : 2000 : R2010 | Standard Practice for General Techniques of Gas Chromatography Infrared (GC/IR) Analysis |
| ISO 15063:2011 | Plastics Polyols for use in the production of polyurethanes Determination of hydroxyl number by NIR spectroscopy |
| ASTM D 3124 : 1998 : R2011 | Standard Test Method for Vinylidene Unsaturation in Polyethylene by Infrared Spectrophotometry |
| ASTM D 7889 : 2013 | Standard Test Method for Field Determination of In-Service Fluid Properties Using IR Spectroscopy |
| ASTM E 1944:1998 | Standard Practice for Describing and Measuring Performance of Laboratory Fourier Transform Near-Infrared (FT-NIR) Spectrometers: Level Zero and Level One Tests |
| ASTM D 6645 : 2001 : R2010 | Standard Test Method for Methyl (Comonomer) Content in Polyethylene by Infrared Spectrophotometry |
| ASTM E 573 : 2001 : R2007 | Standard Practices for Internal Reflection Spectroscopy |
| ASTM E 1252 : 1998 : R2013 : EDT 1 | Standard Practice for General Techniques for Obtaining Infrared Spectra for Qualitative Analysis |
| ASTM E 1982 : 1998 : R2002 | Standard Practice for Open-Path Fourier Transform Infrared (OP/FT-IR) Monitoring of Gases and Vapors in Air |
| ASTM F 1864 : 2016 : REDLINE | Standard Test Method for Dust Erosion Resistance of Optical and Infrared Transparent Materials and Coatings |
| ASTM D 2702 : 2005 : R2011 | Standard Practice for Rubber Chemicals—Determination of Infrared Absorption Characteristics |
| SAE AMS 3915 : 2015 | ADVANCED COMPOSITES PREPREG - NOMINAL 250 DEGREES F CURE - GLASS FIBER AND EPOXY RESIN, 7781 WEAVE FABRIC |
| ASTM D 7066 : 2004 : R2011 | Standard Test Method for dimer/trimer of chlorotrifluoroethylene (S-316) Recoverable Oil and Grease and Nonpolar Material by Infrared Determination |
| ASTM D 3900 : 2017 : REDLINE | Standard Test Methods for Rubber—Determination of Ethylene Units in Ethylene-Propylene Copolymers (EPM) and in Ethylene-Propylene-Diene Terpolymers (EPDM) by Infrared Spectrometry |
| ASTM D 7066 : 2004 | Standard Test Method for dimer/trimer of chlorotrifluoroethylene (S-316) Recoverable Oil and Grease and Nonpolar Material by Infrared Determination |
| ASTM D 3677 : 2010 : EDT 1 | Standard Test Methods for Rubber<char: emdash>Identification by Infrared Spectrophotometry |
| MIL-T-70681 Base Document:1988 | TRIPHENYL BISMUTH |
| SAE AMS 3961 : 2015 | 350 DEGREES F AUTOCLAVE CURE, LOW FLOW TOUGHENED EPOXY PREPREGS |
| MIL-M-70605 Base Document:1988 | 2,2'-METHYLENEBIS (4-METHYL-6-TERT-BUTYLPHENOL) |
| ASTM D 3288/D3288M : 2015 : REDLINE | Standard Test Methods for Magnet-Wire Enamels |
| ASTM D 3594 : 1993 : R2013 | Standard Test Method for Copolymerized Ethyl Acrylate In Ethylene-Ethyl Acrylate Copolymers (Withdrawn 2019) |
| SAE AMS 3909 : 2014 | CLOTH, ARAMID, INTERMEDIATE MODULUS |
| SAE AMS 3914A : 2015 | ADVANCED COMPOSITES PREPREG - NOMINAL 250 DEGREES F CURE - 12K TOW CARBON FIBER AND EPOXY RESIN, PLAIN WEAVE FABRIC |
| ASTM E 60 : 2011 : R2016 | Standard Practice for Analysis of Metals, Ores, and Related Materials by Spectrophotometry |
| ASTM E 275 : 2008 | Describing and Measuring Performance of Ultraviolet and Visible Spectrophotometers |
| ASTM D 2238 : 1992 : R2012 : EDT 1 | Standard Test Methods for Absorbance of Polyethylene Due to Methyl Groups at 1378 cm<sup>−1</sup> (Withdrawn 2021) |
| ASTM D 3677 : 2010 : R2015 | Standard Test Methods for Rubber—Identification by Infrared Spectrophotometry |
| ASTM E 2105 : 2000 | Standard Practice for General Techniques of Thermogravimetric Analysis (TGA) Coupled With Infrared Analysis (TGA/IR) |
| ASTM D 2144 : 2007 | Standard Practices for Examination of Electrical Insulating Oils by Infrared Absorption |
| ASTM D 3921 : 1996 : R2003 : EDT 1 | Standard Test Method for Oil and Grease and Petroleum Hydrocarbons in Water |
| ASTM E 334 : 2001 : R2007 | Standard Practice for General Techniques of Infrared Microanalysis |
| ASTM E 204 : 1998 : R2002 | Standard Practices for Identification of Material by Infrared Absorption Spectroscopy, Using the ASTM Coded Band and Chemical Classification Index |
| ASTM D 8074 : 2016 | Standard Test Method for Evaluation of Diesel Engine Oils in DD13 Diesel Engine |
| ASTM E 1642 : 2000 : R2016 | Standard Practice for General Techniques of Gas Chromatography Infrared (GC/IR) Analysis |
| ASTM D 3677 : 2010 | Standard Test Methods for Rubber--Identification by Infrared Spectrophotometry |
| ASTM D 7575 : 2011 : R2017 | Standard Test Method for Solvent-Free Membrane Recoverable Oil and Grease by Infrared Determination |
| ASTM D 5576 : 2000 : R2006 | Standard Practice for Determination of Structural Features in Polyolefins and Polyolefin Copolymers by Infrared Spectrophotometry (FT-IR) |
| ASTM F 1109 : 1987 | Specification for Porous Composites of Polytetrafluoroethylene and Carbon for Surgical Implant Applications (Withdrawn 1993) |
| ASTM E 2412 : 2010 : R2018 | Standard Practice for Condition Monitoring of In-Service Lubricants by Trend Analysis Using Fourier Transform Infrared (FT-IR) Spectrometry |
| ASTM D 6047 : 2017 : REDLINE | Standard Test Methods for Rubber, Raw—Determination of 5-Ethylidenenorbornene (ENB) or Dicyclopentadiene (DCPD) in Ethylene-Propylene-Diene (EPDM) Terpolymers |
| SAE AMS6562:2023 | Medium Temperature, Out-of-Autoclave, Oven-Vacuum-Bag Cure Epoxy Resin Impregnated Fiber Reinforced Composite Materials |
| ASTM E 1421 : 1999 : R2021 | Standard Practice for Describing and Measuring Performance of Fourier Transform Mid-Infrared (FT-MIR) Spectrometers: Level Zero and Level One Tests |
| ASTM E 1421 : 1999 : R2004 | Standard Practice for Describing and Measuring Performance of Fourier Transform Mid-Infrared (FT-MIR) Spectrometers: Level Zero and Level One Tests |
| ASTM E 1252 : 1998 : R2007 | Standard Practice for General Techniques for Obtaining Infrared Spectra for Qualitative Analysis |
| ASTM E 1252 : 1998 | Standard Practice for General Techniques for Obtaining Infrared Spectra for Qualitative Analysis |
| ASTM E 932 : 1989 : R2013 | Standard Practice for Describing and Measuring Performance of Dispersive Infrared Spectrometers |
| ASTM E 1655 : 2004 | Standard Practices for Infrared Multivariate Quantitative Analysis |
| ASTM E 1421 : 1999 : R2009 | Standard Practice for Describing and Measuring Performance of Fourier Transform Mid-Infrared (FT-MIR) Spectrometers: Level Zero and Level One Tests |
| ASTM E 1421 : 1999 : R2015 : EDT 1 | Standard Practice for Describing and Measuring Performance of Fourier Transform Mid-Infrared (FT-MIR) Spectrometers: Level Zero and Level One Tests |
| ASTM E 932 : 1989 : R2021 | Standard Practice for Describing and Measuring Performance of Dispersive Infrared Spectrometers |
| ASTM E 1252 : 1998 : R2021 | Standard Practice for General Techniques for Obtaining Infrared Spectra for Qualitative Analysis |
| ASTM E 1421 : 1999 | Standard Practice for Describing and Measuring Performance of Fourier Transform Mid-Infrared (FT-MIR) Spectrometers Level Zero and Level One Tests |
| ASTM E 334 : 2001 : R2021 | Standard Practice for General Techniques of Infrared Microanalysis |
| ASTM E 1655 : 2017 | Standard Practices for Infrared Multivariate Quantitative Analysis |
| ASTM E 1655 : 2000 | Standard Practices for Infrared Multivariate Quantitative Analysis |
| ASTM E 1655 : 2005 | Standard Practices for Infrared Multivariate Quantitative Analysis |
| ASTM E 334 : 2001 : R2013 | Standard Practice for General Techniques of Infrared Microanalysis |
| ASTM E 1655 : 2005 : R2012 | Standard Practices for Infrared Multivariate Quantitative Analysis |
| ASTM E 1252 : 1998 : R2013 : EDT 1 | Standard Practice for General Techniques for Obtaining Infrared Spectra for Qualitative Analysis |
| ASTM E 1252 : 1998 : R2002 | Standard Practice for General Techniques for Obtaining Infrared Spectra for Qualitative Analysis |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.