ASTM E 1640 : 2018
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Assignment of the Glass Transition Temperature By Dynamic Mechanical Analysis
Hardcopy , PDF
08-18-2023
English
08-06-2018
Important note : All end users must be registered with an Account prior to user licenses being assigned.1.This test method covers the assignment of a glass transition temperature (Tg) of materials using dynamic mechanical analyzers
| Committee |
E 37
|
| DocumentType |
Test Method
|
| Pages |
6
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This test method covers the assignment of a glass transition temperature (Tg) of materials using dynamic mechanical analyzers.
1.2This test method is applicable to thermoplastic polymers, thermoset polymers, and partially crystalline materials which are thermally stable in the glass transition region.
1.3The applicable range of temperatures for this test method is dependent upon the instrumentation used, but, in order to encompass all materials, the minimum temperature should be about −150 °C.
1.4This test method is intended for materials having an elastic modulus in the range of 0.5 MPa to 100 GPa.
1.5The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.6This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.7This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM F 3131 : 2014 | Standard Specification for Epoxy / Cotton Raw Materials for the Use in Bearing Cages |
| ASTM F 3131 : 2014 : R2023 | Standard Specification for Epoxy / Cotton Raw Materials for the Use in Bearing Cages |
| ASTM E 2602 : 2022 | Standard Test Methods for Assignment of the Glass Transition Temperature by Modulated Temperature Differential Scanning Calorimetry |
| ASTM E 3301 : 2022 | Standard Test Method for Temperature Calibration of Dynamic Mechanical Analyzers Using Thermal Lag |
| ASTM D 3794 : 2022 | Standard Guide for Testing Coil Coatings |
| ASTM F 790 : 2023 | Standard Guide for Testing Materials for Aerospace Plastic Transparent Enclosures |
| ASTM F 942 : 2018 : R2023 : EDT 1 | Standard Guide for Selection of Test Methods for Interlayer Materials for Aerospace Transparent Enclosures |
| ASTM D 3794 : 2018 | Standard Guide for Testing Coil Coatings |
| ASTM F 942 : 2018 | Standard Guide for Selection of Test Methods for Interlayer Materials for Aerospace Transparent Enclosures |
| ASTM D 7028 : 2007 : R2015 | Standard Test Method for Glass Transition Temperature (DMA Tg) of Polymer Matrix Composites by Dynamic Mechanical Analysis (DMA) |
| ASTM E 1867 : 2018 | Standard Test Methods for Temperature Calibration of Dynamic Mechanical Analyzers |
| ASTM E 2602 : 2009 : R2015 | Standard Test Methods for the Assignment of the Glass Transition Temperature by Modulated Temperature Differential Scanning Calorimetry |
| ASTM E 1142 : 2022 | Standard Terminology Relating to Thermophysical Properties |
| ASTM E 2254 : 2013 | Standard Test Method for Storage Modulus Calibration of Dynamic Mechanical Analyzers |
| ASTM E 1545 : 2005 | Standard Test Method for Assignment of the Glass Transition Temperature by Thermomechanical Analysis |
| ASTM E 1363 : 1997 : EDT 1 | Standard Test Method for Temperature Calibration of Thermomechanical Analyzers |
| ASTM E 2877 : 2012 : EDT 1 | Standard Guide for Digital Contact Thermometers |
| ASTM E 2254 : 2011 | Standard Test Method for Storage Modulus Calibration of Dynamic Mechanical Analyzers |
| ASTM E 1867 : 2016 | Standard Test Methods for Temperature Calibration of Dynamic Mechanical Analyzers |
| ASTM D 4092 : 2007 : R2013 | Standard Terminology for Plastics: Dynamic Mechanical Properties |
| ASTM E 1867 : 2022 | Standard Test Methods for Temperature Calibration of Dynamic Mechanical Analyzers |
| ASTM D 4092 : 1996 | Standard Terminology: Plastics: Dynamic Mechanical Properties |
| ASTM E 1142 : 2011 : REV A | Standard Terminology Relating to Thermophysical Properties |
| ASTM E 1142 : 2012 | Standard Terminology Relating to Thermophysical Properties |
| ASTM E 1142 : 1997 | Standard Terminology Relating to Thermophysical Properties |
| ASTM E 1867 : 1997 | Standard Test Method for Temperature Calibration of Dynamic Mechanical Analyzers |
| ASTM E 1142 : 2013 | Standard Terminology Relating to Thermophysical Properties |
| ASTM E 1545 : 2022 | Standard Test Method for Assignment of the Glass Transition Temperature by Thermomechanical Analysis |
| ASTM E 1142 : 2004 | Standard Terminology Relating to Thermophysical Properties |
| ASTM E 1142 : 2022 : REV A | Standard Terminology Relating to Thermophysical Properties |
| ASTM E 1142 : 2022 : REV C | Standard Terminology Relating to Thermophysical Properties |
| ASTM E 1142 : 2006 : REV A | Standard Terminology Relating to Thermophysical Properties |
| ASTM E 2425 : 2021 | Standard Test Method for Loss Modulus Conformance of Dynamic Mechanical Analyzers |
| ASTM E 691 : 2020 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM E 2254 : 2003 | Standard Test Method for Storage Modulus Calibration of Dynamic Mechanical Analyzers |
| ASTM E 1142 : 2015 : R2020 | Standard Terminology Relating to Thermophysical Properties |
| ASTM D 4092 : 2021 | Standard Terminology for Plastics: Dynamic Mechanical Properties |
| ASTM E 1142 : 2021 : REV A | Standard Terminology Relating to Thermophysical Properties |
| ASTM E 1363 : 2016 | Standard Test Method for Temperature Calibration of Thermomechanical Analyzers |
| ASTM D 4092 :2007 | Standard Terminology: Plastics: Dynamic Mechanical Properties |
| ASTM E 1545 : 2011 : R2016 | Standard Test Method for Assignment of the Glass Transition Temperature by Thermomechanical Analysis |
| ASTM E 1867 : 2012 | Standard Test Method for Temperature Calibration of Dynamic Mechanical Analyzers |
| ASTM E 691 : 2019 : EDT 1 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM E 1363 : 2008 | Standard Test Method for Temperature Calibration of Thermomechanical Analyzers |
| ASTM E 691 : 2023 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM D 4092 : 2001 | Standard Terminology: Plastics: Dynamic Mechanical Properties |
| ASTM E 2425 : 2005 | Standard Test Method for Loss Modulus Conformance of Dynamic Mechanical Analyzers |
| ASTM E 2877 : 2012 : R2019 | Standard Guide for Digital Contact Thermometers |
| ASTM E 691 : 2022 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM E 1867 : 2001 | Standard Test Method for Temperature Calibration of Dynamic Mechanical Analyzers |
| ASTM E 691 : 2009 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM E 1142 : 2007 | Standard Terminology Relating to Thermophysical Properties |
| ASTM E 2254 : 2018 | Standard Test Method for Storage Modulus Calibration of Dynamic Mechanical Analyzers |
| ASTM E 1867 : 2018 | Standard Test Methods for Temperature Calibration of Dynamic Mechanical Analyzers |
| ASTM E 691 : 2021 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM E 1142 : 2022 : REV B | Standard Terminology Relating to Thermophysical Properties |
| ASTM E 2254 : 2009 | Standard Test Method for Storage Modulus Calibration of Dynamic Mechanical Analyzers |
| ASTM E 1142 : 2014 : REV A | Standard Terminology Relating to Thermophysical Properties |
| ASTM E 1363 : 2018 | Standard Test Method for Temperature Calibration of Thermomechanical Analyzers |
| ASTM E 1545 : 2011 | Standard Test Method for Assignment of the Glass Transition Temperature by Thermomechanical Analysis |
| ASTM E 1545 : 2000 | Standard Test Method for Assignment of the Glass Transition Temperature by Thermomechanical Analysis |
| ASTM E 2877 : 2012 | Standard Guide for Standard Guide for Digital Contact Thermometers |
| ASTM E 1363 : 2003 | Standard Test Method for Temperature Calibration of Thermomechanical Analyzers |
| ASTM E 1142 : 2014 : REV B | Standard Terminology Relating to Thermophysical Properties |
| ASTM E 1142 : 2023 | Standard Terminology Relating to Thermophysical Properties |
| ASTM E 1363 : 2013 | Standard Test Method for Temperature Calibration of Thermomechanical Analyzers |
| ASTM E 1142 : 2005 | Standard Terminology Relating to Thermophysical Properties |
| ASTM E 1142 : 2015 | Standard Terminology Relating to Thermophysical Properties |
| ASTM E 1867 : 2011 | Standard Test Method for Temperature Calibration of Dynamic Mechanical Analyzers |
| ASTM E 1867 : 2013 | Standard Test Method for Temperature Calibration of Dynamic Mechanical Analyzers |
| ASTM E 2425 : 2011 | Standard Test Method for Loss Modulus Conformance of Dynamic Mechanical Analyzers |
| ASTM E 2254 : 2008 | Standard Test Method for Storage Modulus Calibration of Dynamic Mechanical Analyzers |
| ASTM E 1142 : 2011 : REV B | Standard Terminology Relating to Thermophysical Properties |
| ASTM E 1142 : 2021 | Standard Terminology Relating to Thermophysical Properties |
| ASTM E 2425 : 2016 | Standard Test Method for Loss Modulus Conformance of Dynamic Mechanical Analyzers |
| ASTM E 1142 : 2023 : REV A | Standard Terminology Relating to Thermophysical Properties |
| ASTM E 1867 : 2006 | Standard Test Method for Temperature Calibration of Dynamic Mechanical Analyzers |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.