ASTM E 1399/E1399M : 1997 : R2017
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Cyclic Movement and Measuring the Minimum and Maximum Joint Widths of Architectural Joint Systems
Hardcopy , PDF
10-11-2022
English
09-06-2017
Important note : All end users must be registered with an Account prior to user licenses being assigned.CONTAINED IN VOL. 04.11, 2017 Defines testing procedures for architectural joint systems.
| Committee |
E 06
|
| DevelopmentNote |
Supersedes ASTM E 1399. (09/2013)
|
| DocumentType |
Test Method
|
| Pages |
6
|
| ProductNote |
Reconfirmed 2017
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This test method covers testing procedures for architectural joint systems. This test method is intended for the following uses for architectural joint systems:
1.1.1To verify movement capability information supplied to the user by the producer,
1.1.2To standardize comparison of movement capability by relating it to specified nominal joint widths,
1.1.3To determine the cyclic movement capability between specified minimum and maximum joint widths without visual deleterious effects, and
1.1.4To provide the user with graphic information, drawings or pictures in the test report, depicting them at minimum, maximum, and nominal joint widths during cycling.
1.2This test method is intended to be used only as part of a specification or acceptance criterion due to the limited movements tested.
1.3The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM E 1612/E1612M : 1994 : R2022 | Standard Specification for Preformed Architectural Compression Seals for Buildings and Parking Structures |
| ASTM E 1783/E1783M : 1996 : R2017 | Standard Specification for Preformed Architectural Strip Seals for Buildings and Parking Structures |
| ASTM E 3037 : 2020 | Standard Test Method for Measuring Relative Movement Capabilities of Through-Penetration Firestop Systems |
| ASTM D 1079 : 2018 : EDT 1 | Standard Terminology Relating to Roofing and Waterproofing |
| ASTM E 631 : 2015 : REDLINE | Standard Terminology of Building Constructions |
| ASTM D 1079 : 2008 : REV A | Standard Terminology Relating to Roofing and Waterproofing |
| ASTM C 794 : 2018 | Standard Test Method for Adhesion-in-Peel of Elastomeric Joint Sealants |
| ASTM D 1079 : 2016 | Standard Terminology Relating to Roofing and Waterproofing |
| ASTM C 719 : 2022 | Standard Test Method for Adhesion and Cohesion of Elastomeric Joint Sealants Under Cyclic Movement (Hockman Cycle) |
| ASTM D 1079 : 2006 | Terminology Relating to Roofing and Waterproofing |
| ASTM D 1079 : 2020 | Standard Terminology Relating to Roofing and Waterproofing |
| ASTM C 962 : 86 E1 | GUIDE FOR USE OF ELASTOMERIC JOINT SEALANTS |
| ASTM D 1079 : 2013 | Standard Terminology Relating to Roofing and Waterproofing |
| ASTM D 1079 : 2007 : REV A | Terminology Relating to Roofing and Waterproofing |
| ASTM D 1079 : 2010 | Standard Terminology Relating to Roofing and Waterproofing |
| IEEE/ASTM SI_10-2010 | American National Standard for Metric Practice |
| ASTM D 1079 : 2018 | Standard Terminology Relating to Roofing and Waterproofing |
| ASTM C 794 : 2018 : R2022 | Standard Test Method for Adhesion-in-Peel of Elastomeric Joint Sealants |
| ASTM D 1079 : 2005 : REV A | Terminology Relating to Roofing and Waterproofing |
| ASTM C 719 : 2014 : R2019 | Standard Test Method for Adhesion and Cohesion of Elastomeric Joint Sealants Under Cyclic Movement (Hockman Cycle) |
| ASTM D 1079 : 2002 | Standard Terminology Relating to Roofing, Waterproofing, and Bituminous Materials |
| ASTM D 1079 : 2001 | Standard Terminology Relating to Roofing, Waterproofing, and Bituminous Materials |
| ASTM C 962 : 1988 : EDT 1 | Guide for Use of Elastomeric Joint Sealants |
| ASTM D 1079 : 2000 : REV A | Standard Terminology Relating to Roofing, Waterproofing, and Bituminous Materials |
| ASTM D 1079 : 2013 : EDT 1 | Standard Terminology Relating to Roofing and Waterproofing |
| ASTM D 1079 : 2009 | Standard Terminology Relating to Roofing and Waterproofing |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.