ASTM E 1118 : 2005
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Practice for Acoustic Emission Examination of Reinforced Thermosetting Resin Pipe (RTRP)
Hardcopy , PDF
11-11-2014
ASTM E 1118/E1118M : 2011
ASTM E 1118/E1118M : 2016 : REDLINE
English
06-01-2005
CONTAINED IN VOL. 03.03, 2005 Describes acoustic emission examination or monitoring of Reinforced Thermosetting Resin Pipe to establish structural integrity.
Committee |
E 07
|
DocumentType |
Standard Practice
|
Pages |
12
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
1.1 This practice covers acoustic emission (AE) examination or monitoring of reinforced thermosetting resin pipe (RTRP) to determine structural integrity. It is applicable to lined or unlined pipe, fittings, joints, and piping systems.
1.2 This practice is applicable to pipe that is fabricated with fiberglass and carbon fiber reinforcements with reinforcing contents greater than 15 % by weight. The suitability of these procedures must be demonstrated before they are used for piping that is constructed with other reinforcing materials.
1.3 This practice is applicable to tests below pressures of 35 MPa absolute (5000 psia).
1.4 This practice is limited to pipe up to and including 0.6 m (24 in.) in diameter. Larger diameter pipe can be examined with AE, however, the procedure is outside the scope of this practice.
1.5 This practice applies to examinations of new or in-service RTRP.
1.6 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to use. For more specific safety precautionary information see 8.1.
OLF 055 : 1997 | RECOMMENDED GUIDELINES FOR NDT OF GRP PIPE SYSTEMS AND TANKS |
ASTM E 543 : 2015 : REDLINE | Standard Specification for Agencies Performing Nondestructive Testing |
ASTM E 2981 : 2015 | Standard Guide for Nondestructive Testing of the Composite Overwraps in Filament Wound Pressure Vessels Used in Aerospace Applications |
API 574 REDLINE : 2009 | INSPECTION PRACTICES FOR PIPING SYSTEM COMPONENTS |
ASTM E 543 : 2015 | Standard Specification for Agencies Performing Nondestructive Testing |
API 574 CHINESE : 2009 | INSPECTION PRACTICES FOR PIPING SYSTEM COMPONENTS |
ASNT SNT TC 1A : 2016 | TOPICAL OUTLINES FOR QUALIFICATION OF NONDESTRUCTIVE TESTING PERSONNEL |
NAS410:2003 | NAS CERTIFICATION & QUALIFICATION OF NONDESTRUCTIVE TEST PERSONNEL |
ASTM E 750 : 2015 : REDLINE | Standard Practice for Characterizing Acoustic Emission Instrumentation |
ASNT CP 189 : 2016 | QUALIFICATION AND CERTIFICATION OF NONDESTRUCTIVE TESTING PERSONNEL |
ASTM E 650 : 1997 | Standard Guide for Mounting Piezoelectric Acoustic Emission Sensors |
ASTM E 976 : 2015 : REDLINE | Standard Guide for Determining the Reproducibility of Acoustic Emission Sensor Response |
ASTM E 543 : 2015 : REDLINE | Standard Specification for Agencies Performing Nondestructive Testing |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.