ASTM E 103 : 2017 : REDLINE
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Practice for Rapid Indentation Hardness Testing of Metallic Materials
07-29-2024
English
04-01-2017
Important note : All end users must be registered with an Account prior to user licenses being assigned.CONTAINED IN VOL. 03.01, 2017 Defines a procedure for rapid indentation hardness testing of metallic materials.
| Committee |
E 28
|
| DocumentType |
Redline
|
| Pages |
5
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy |
1.1This practice covers a procedure for rapid indentation hardness testing of metallic materials.
1.2This practice includes additional requirements in Annex A1 for the direct, indirect, and daily verification of rapid indentation hardness testing machines.
1.3The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| MIL P 64008 : 0 | PROJECTILE, 155MM: XM825 METAL PARTS ASSEMBLY |
| MIL-P-50345 Revision F:1994 | PROJECTILES,155MM:M483A1-M718/M741-M692/M731 METAL PARTS ASSEMBLY |
| MIL-DTL-60547 Revision G:2008 | PROJECTILE, 105 MM, HE, M1 AND M760 - METAL PARTS ASSEMBLY |
| SAE AMS5663N | NICKEL ALLOY, CORROSION AND HEAT-RESISTANT, BARS, FORGINGS, AND RINGS 52.5NI - 19CR - 3.0MO - 5.1CB (NB) - 0.90TI - 0.50AL - 18FE CONSUMABLE ELECTRODE OR VACUUM INDUCTION MELTED 1775 DEGREES F (968 DEGREES C) SOLUTION AND PRECIPITATION HEAT TREATED |
| MIL P 60584 : A | PROJECTILE, 155MM, SMOKE, WP, M110 METAL PARTS ASSEMBLY |
| MIL-DTL-63245 Revision C:2008 | Projectile 155 Millimeter: HE, Metal Parts Assembly, M795 |
| SAE AMS 5442 : 2017 | NICKEL ALLOY, CORROSION AND HEAT-RESISTANT, BARS, FORGINGS, AND RINGS, NI - 18CR - 2.8MO - 5.5CB(NB) - 0.70TI - 1.50AL - 10FE - 9CO - 1W, CONSUMABLE ELECTRODE REMELTED OR VACUUM INDUCTION MELTED, 1775 DEGREES F (968 DEGREES C) SOLUTION AND PRECIPITATION HEAT TREATED |
| MIL-P-70524 Base Document:1990 | PROJECTILE, 105 MM, HE, RA, XM913/XM927 WARHEAD INSULATION ASSEMBLY FOR |
| SAE AMSH6088C | Heat Treatment of Aluminum Alloys |
| MIL-DTL-60584 Revision B:2006 | Projectile,155 Millimeter - Smoke, WP, Metal Parts Assembly, M110A2 |
| SAE AMS7490Q | RINGS, FLASH WELDED, CORROSION AND HEAT-RESISTANT AUSTENITIC STEELS, AUSTENITIC-TYPE IRON, NICKEL, OR COBALT ALLOYS, OR PRECIPITATION-HARDENABLE ALLOYS |
| SAE AMS 5962 : 2012 | NICKEL ALLOY, CORROSION AND HEAT-RESISTANT, ROUND BARS AND WIRE, 52.5NI - 19CR - 3.0MO - 5.1CB - 0.90TI - 0.50AL - 18FE, CONSUMABLE ELECTRODE OR VACUUM INDUCTION MELTED, 1775 DEGREES F (968 DEGREES C) SOLUTION TREATED AND WORK STRENGTHENED, PRECIPITATION HARDENABLE |
| SAE AMS 5441 : 2016 | NICKEL ALLOY, CORROSION AND HEAT-RESISTANT, BARS, FORGINGS, AND RINGS, NI - 18CR - 2.8MO - 5.5CB(NB) - 0.70TI - 1.50AL - 10FE - 9CO - 1W, CONSUMABLE ELECTRODE REMELTED OR VACUUM INDUCTION MELTED, 1775 DEGREES F (968 DEGREES C) SOLUTION HEAT TREATED, PRECIPITATION-HARDENABLE |
| MIL-H-6088 Revision G:1991 | HEAT TREATMENT OF ALUMINIUM ALLOYS |
| MIL P 14824 : B | PROJECTILE, H.E., 155MM, M107 METAL PARTS ASSEMBLY |
| SAE AMS5884D | IRON-NICKEL ALLOY, BARS, FORGINGS, AND RINGS, 42FE - 37.5NI - 14CO - 4.8CB(NB) - 1.6TI, SOLUTION HEAT TREATED, PRECIPITATION HARDENABLE MULTIPLE MELTED, HIGH TEMPERATURE, LOW EXPANSION |
| MIL-P-48323 Revision C:1984 | PROJECTILE, 8 INCH, HE, RA, M650 ROCKET MOTOR BODY ASSEMBLY |
| SAE AMS5662N | NICKEL ALLOY, CORROSION AND HEAT-RESISTANT, BARS, FORGINGS, AND RINGS 52.5NI - 19CR - 3.0MO - 5.1CB (NB) - 0.90TI - 0.50AI - 18FE CONSUMABLE ELECTRODE OR VACUUM INDUCTION MELTED 1775 DEGREES F (968 DEGREES C) SOLUTION HEAT TREATED, PRECIPITATION-HARDENABLE |
| MIL-DTL-14824 Revision C:2007 | PROJECTILE 155 MM, HE, METAL PARTS ASSEMBLY, M107 |
| MIL-P-70612 Revision A:1993 | PROJECTILE, 155MM, XM864 BASE ASSEMBLY FOR |
| ASTM A 880 : 1995 | Standard Practice for Criteria for Use in Evaluation of Testing Laboratories and Organizations for Examination and Inspection of Steel, Stainless Steel, and Related Alloys (Withdrawn 2004) |
| ISO/IEC 17025:2005 | General requirements for the competence of testing and calibration laboratories |
| ASTM E 10 : 2017-05 | TEST METHOD FOR BRINELL HARDNESS OF METALLIC MATERIALS |
| ISO/IEC 17011:2004 | Conformity assessment General requirements for accreditation bodies accrediting conformity assessment bodies |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.