ASTM D 8166 : 2021 : REV A
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Sizing and Counting Particulates in Middle Distillate Fuels and Biodiesel Blend (B6 to B20) Using Continuous Flow and Bottle Sampler Automatic Particle Condition Monitors
Hardcopy , PDF
11-05-2022
English
03-24-2021
Important note : All end users must be registered with an Account prior to user licenses being assigned.| Committee |
D 02
|
| DocumentType |
Test Method
|
| Pages |
8
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This test method uses specific automatic particle condition monitors (PCMs) to count and measure the size of dispersed dirt particles, water droplets and other particulates, in middle distillate fuel, in the overall range from 4 µm to 70 µm and in the size bands ≥4 µm, ≥6 µm, ≥14 µm, and ≥30 µm.
1.2This test method has interim repeatability precision only, see Section 14 for more information.
Note 1:ASTM specification fuels falling within the scope of this test method include Specifications: D975, D1655, D3699, D7467, MIL-DTL-83133, MIL-DTL-5624, and distillate grades of D396 and D2880.
Note 2:For the purposes of this test method, water droplets are counted as particles, and agglomerated particles are detected and counted as a single larger particle. Dirt includes microbial particulates. Although the projected area of a particle is measured, this is expressed as the diameter of a circle for the purposes of this test method. The detector is unable to distinguish between dirt and water particles.
Note 3:This test method may be used for particle sizes bands up to 70 µm, however the interim repeatability has only been determined for the size bands ≥4 µm, ≥6 µm, and ≥14 µm. All measurements are counts per millilitre.
1.3The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM D 4057 : 2019 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
| ASTM D 7619 : 2022 | Standard Test Method for Sizing and Counting Particles in Light and Middle Distillate Fuels, by Automatic Particle Counter |
| ASTM D 4175 : 2020 : REV B | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 396 : 2020 | Standard Specification for Fuel Oils |
| ASTM D 975 : 2022 | Standard Specification for Diesel Fuel |
| ASTM D 1655 : 2021 : REV A | Standard Specification for Aviation Turbine Fuels |
| ASTM D 1655 : 2020 : REV D | Standard Specification for Aviation Turbine Fuels |
| ASTM D 4175 : 2022 | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 1655 : 2022 | Standard Specification for Aviation Turbine Fuels |
| ASTM D 975 : 2021 | Standard Specification for Diesel Fuel |
| ASTM D 4175 : 2020 : REV B : EDT 1 | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 6300 : 2021 | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 975 : 2020 : REV C | Standard Specification for Diesel Fuel |
| ASTM D 6300 : 2020 : REV B | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 1655 : 2021 : REV B | Standard Specification for Aviation Turbine Fuels |
| ASTM D 4177 : 2022 | Standard Practice for Automatic Sampling of Petroleum and Petroleum Products |
| ASTM D 7619 : 2017 | Standard Test Method for Sizing and Counting Particles in Light and Middle Distillate Fuels, by Automatic Particle Counter |
| ASTM D 1655 : 2021 | Standard Specification for Aviation Turbine Fuels |
| ASTM D 1655 : 2021 : REV C | Standard Specification for Aviation Turbine Fuels |
| ASTM D 396 : 2021 | Standard Specification for Fuel Oils |
| ASTM D 4057 : 2022 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
| ASTM D 4306 : 2020 | Standard Practice for Aviation Fuel Sample Containers for Tests Affected by Trace Contamination |
| ASTM D 4177 : 2020 | Standard Practice for Automatic Sampling of Petroleum and Petroleum Products |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.