ASTM D 8 : 2020 : REV A
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Terminology Relating to Materials for Roads and Pavements
Hardcopy , PDF
02-03-2021
English
09-11-2020
Committee |
D 04
|
DocumentType |
Reference Material
|
Pages |
5
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
1.1This standard incorporates generic terms and generic definitions of terms specifically associated with road and paving materials. These generic terms and definitions are used within the standards developed by Committee D04 on Road and Paving Materials.
1.2Only terms that appear in more than one standard under the jurisdiction of Committee D04 will be included in Section 3 of Terminology D8. Terms that were historically part of this terminology but never appeared, or no longer appear, in more than one standard under the jurisdiction of Committee D04 are listed in Appendix X1. The terms in Appendix X1 are not maintained and updated by Subcommittee D04.91. The terms in Appendix X1 are available for reference purposes only. The terminology in Appendix X1 may not reflect current practices, standards, and technology used in materials for roads and pavements.
1.3This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM D 7643 : 2016 | Standard Practice for Determining the Continuous Grading Temperatures and Continuous Grades for PG Graded Asphalt Binders |
ASTM D 5821 : 2013 : R2017 | Standard Test Method for Determining the Percentage of Fractured Particles in Coarse Aggregate |
ASTM D 6088 : 2006 : R2016 | Standard Practice for Installation of Geocomposite Pavement Drains |
ASTM D 692/D692M : 2020 | Standard Specification for Coarse Aggregate for Asphalt Paving Mixtures |
ASTM D 6155 : 2019 | Standard Specification for Nontraditional Coarse Aggregates for Asphalt Paving Mixtures |
ASTM D 7115 : 2020 | Standard Test Method for Measurement of Superpave Gyratory Compactor (SGC) Internal Angle of Gyration Using Simulated Loading |
ASTM D 4469 : 2017 | Standard Practice for Calculating Percent Asphalt Absorption by the Aggregate in Asphalt Mixtures |
ASTM D 6816 : 2011 : R2016 | Standard Practice for Determining Low-Temperature Performance Grade (PG) of Asphalt Binders |
ASTM D 242/D242M : 2019 | Standard Specification for Mineral Filler for Asphalt Mixtures |
ASTM D 6521 : 2019 : REV A | Standard Practice for Accelerated Aging of Asphalt Binder Using a Pressurized Aging Vessel (PAV) |
ASTM D 2321 : 2020 | Standard Practice for Underground Installation of Thermoplastic Pipe for Sewers and Other Gravity-Flow Applications |
ASTM D 8140 : 2018 | Standard Guide for the Use of Foundry Sand in Asphalt Mixtures |
ASTM D 8237 : 2018 | Standard Test Method for Determining Fatigue Failure of Asphalt-Aggregate Mixtures With the Four-Point Beam Fatigue Device |
ASTM D 2940/D2940M : 2020 | Standard Specification for Graded Aggregate Material for Bases or Subbases for Highways or Airports |
ASTM D 3625/D3625M : 2020 | Standard Practice for Effect of Water on Asphalt-Coated Aggregate Using Boiling Water |
ASTM D 8239 : 2018 | Standard Specification for Performance-Graded Asphalt Binder Using the Multiple Stress Creep and Recovery (MSCR) Test |
ASTM D 7870/D7870M : 2020 | Standard Practice for Moisture Conditioning Compacted Asphalt Mixture Specimens by Using Hydrostatic Pore Pressure |
ASTM D 6752/D6752M : 2018 | Standard Test Method for Bulk Specific Gravity and Density of Compacted Asphalt Mixtures Using Automatic Vacuum Sealing Method |
ASTM D 1369 : 2019 | Standard Practice for Quantities of Materials for Asphalt-Aggregate Surface Treatments |
ASTM D 6297 : 2020 | Standard Specification for Asphaltic Plug Joints for Bridges |
ASTM F 1668 : 2016 | Standard Guide for Construction Procedures for Buried Plastic Pipe |
ASTM D 8225 : 2019 | Standard Test Method for Determination of Cracking Tolerance Index of Asphalt Mixture Using the Indirect Tensile Cracking Test at Intermediate Temperature |
ASTM D 5/D5M : 2020 | Standard Test Method for Penetration of Bituminous Materials |
ASTM D 3839 : 2014 : R2019 | Standard Guide for Underground Installation of “Fiberglass” (Glass-Fiber Reinforced Thermosetting-Resin) Pipe |
ASTM E 867 : 2006 : R2020 | Standard Terminology Relating to Vehicle-Pavement Systems |
ASTM D 6626 : 2015 | Standard Specification for Performance Graded Trinidad Lake Modified Asphalt Binder |
ASTM D 7227/D7227M : 2017 | Standard Practice for Rapid Drying of Compacted Asphalt Mixture Specimens Using Vacuum Drying Apparatus |
ASTM D 75/D75M : 2019 | Standard Practice for Sampling Aggregates |
ASTM D 546 : 2017 | Standard Test Method for Sieve Analysis of Mineral Filler for Asphalt Paving Mixtures |
ASTM D 3549/D3549M : 2018 | Standard Test Method for Thickness or Height of Compacted Asphalt Mixture Specimens |
ASTM D 4223/D4223M : 2020 | Standard Practices for Preparation of Test Specimens of Asphalt-Stabilized Soils |
ASTM D 1754/D1754M : 2020 | Standard Test Method for Effects of Heat and Air on Asphaltic Materials (Thin-Film Oven Test) |
ASTM D 2205 : 2020 | Standard Guide for Selection of Tests for Traffic Paints |
ASTM D 7172 : 2014 | Standard Test Method for Determining the Relative Density (Specific Gravity) and Absorption of Fine Aggregates Using Infrared (Withdrawn 2022) |
ASTM D 7063/D7063M : 2018 | Standard Test Method for Effective Porosity and Effective Air Voids of Compacted Asphalt Mixture Samples |
ASTM D 7229 : 2008 : R2013 : EDT 1 | Standard Test Method for Preparation and Determination of the Bulk Specific Gravity of Dense-Graded Cold Mix Asphalt (CMA) Specimens by Means of the Superpave Gyratory Compactor (Withdrawn 2021) |
ASTM D 243/D243M : 2020 | Standard Test Method for Residue of Specified Penetration |
ASTM D 6704 : 2008 : R2015 | Standard Test Method for Determining the Workability of Asphalt Cold Mix Patching Material |
ASTM D 6925 : 2015 | Standard Test Method for Preparation and Determination of the Relative Density of Asphalt Mix Specimens by Means of the Superpave Gyratory Compactor |
ASTM D 6703 : 2019 | Standard Test Method for Automated Heithaus Titrimetry |
ASTM D 5361/D5361M : 2016 | Standard Practice for Sampling Compacted Asphalt Mixtures for Laboratory Testing |
ASTM D 7405 : 2020 | Standard Test Method for Multiple Stress Creep and Recovery (MSCR) of Asphalt Binder Using a Dynamic Shear Rheometer |
ASTM D 8038 : 2016 | Standard Practice for Reclamation of Recycled Aggregate Base (RAB) Material |
ASTM D 3666 : 2016 | Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials |
ASTM D 5106 : 2015 | Standard Specification for Steel Slag Aggregates for Bituminous Paving Mixtures |
ASTM D 4215 : 2007 : R2013 | Standard Specification for Cold-Mixed, Cold-Laid Bituminous Paving Mixtures |
ASTM D 7369 : 2020 | Standard Test Method for Determining the Resilient Modulus of Asphalt Mixtures by Indirect Tension Test |
ASTM D 7313 : 2020 | Standard Test Method for Determining Fracture Energy of Asphalt Mixtures Using the Disk-Shaped Compact Tension Geometry |
ASTM D 6373 : 2016 | Standard Specification for Performance Graded Asphalt Binder |
ASTM D 3628 : 2015 : R2021 | Standard Practice for Selection and Use of Emulsified Asphalts |
ASTM D 140/D140M : 2016 | Standard Practice for Sampling Asphalt Materials |
ASTM D 1139/D1139M : 2015 | Standard Specification for Aggregate for Single or Multiple Bituminous Surface Treatments |
ASTM D 2170/D2170M : 2018 | Standard Test Method for Kinematic Viscosity of Asphalts |
ASTM D 448 : 2012 : R2017 | Standard Classification for Sizes of Aggregate for Road and Bridge Construction |
ASTM D 2728 : 1998 : R2019 | Standard Practice for Paving Uses and Application Temperatures for Road Tars (Withdrawn 2023) |
ASTM D 2489/D2489M : 2016 | Standard Test Method for Estimating Degree of Particle Coating of Asphalt Mixtures |
ASTM D 8021 : 2020 | Standard Guide for Blast Furnace and Steel Furnace Slag as Produced During the Manufacture of Iron and Steel |
ASTM D 6926 : 2020 | Standard Practice for Preparation of Asphalt Mixture Specimens Using Marshall Apparatus |
ASTM D 2419 : 2014 | Standard Test Method for Sand Equivalent Value of Soils and Fine Aggregate |
ASTM D 2171/D2171M : 2018 | Standard Test Method for Viscosity of Asphalts by Vacuum Capillary Viscometer |
ASTM D 2041/D2041M : 2019 | Standard Test Method for Theoretical Maximum Specific Gravity and Density of Asphalt Mixtures |
ASTM D 1073 : 2016 | Standard Specification for Fine Aggregate for Asphalt Paving Mixtures |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.