ASTM D 7962 : 2017
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Practice for Determination of Minimum Immersion Depth and Assessment of Temperature Sensor Measurement Drift
Hardcopy , PDF
05-15-2021
English
05-18-2017
Important note : All end users must be registered with an Account prior to user licenses being assigned.1.1 This practice describes two procedures for use with temperature measurement devices.
| Committee |
D 02
|
| DocumentType |
Standard Practice
|
| Pages |
3
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This practice describes two procedures for use with temperature measurement devices. Methodology is described for determining minimum immersion depth for thermal sensors, in particular RTDs or similar temperature sensors. Included is a procedure for consistently preparing a reference bath for the purpose of monitoring measurement drift of thermal sensors such as liquid-in-glass or digital contact thermometers.
1.2This practice focuses on temperature measurement drift in a laboratory. If the user requires greater measurement accuracy, then they should follow the instructions in Practice E563.
1.3The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM D 445 : 2019 : REV A | Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity) |
| ASTM D 7279 : 2020 | Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids by Automated Houillon Viscometer |
| ASTM D 7110 : 2021 | Standard Test Method for Determining the Viscosity-Temperature Relationship of Used and Soot-Containing Engine Oils at Low Temperatures |
| ASTM D 8164 : 2021 | Standard Guide for Digital Contact Thermometers for Petroleum Products, Liquid Fuels, and Lubricant Testing |
| ASTM D 5133 : 2020 : REV A | Standard Test Method for Low Temperature, Low Shear Rate, Viscosity/Temperature Dependence of Lubricating Oils Using a Temperature-Scanning Technique |
| ASTM D 2983 : 2020 | Standard Test Method for Low-Temperature Viscosity of Automatic Transmission Fluids, Hydraulic Fluids, and Lubricants using a Rotational Viscometer |
| ASTM D 8278 : 2020 | Standard Specification for Digital Contact Thermometers for Test Methods Measuring Flow Properties of Fuels and Lubricants |
| ASTM D 97 : 2017 : REV B | Standard Test Method for Pour Point of Petroleum Products |
| ASTM D 7279 : 2018 | Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids by Automated Houillon Viscometer |
| ASTM D 445 : 2019 | Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity) |
| ASTM D 2983 : 2019 | Standard Test Method for Low-Temperature Viscosity of Automatic Transmission Fluids, Hydraulic Fluids, and Lubricants using a Rotational Viscometer |
| ASTM D 6371 : 2017 : REV A | Standard Test Method for Cold Filter Plugging Point of Diesel and Heating Fuels |
| ASTM D 5853 : 2017 : REV A | Standard Test Method for Pour Point of Crude Oils |
| ASTM D 4539 : 2017 | Standard Test Method for Filterability of Diesel Fuels by Low-Temperature Flow Test (LTFT) |
| ASTM D 2500 : 2017 : REV A | Standard Test Method for Cloud Point of Petroleum Products and Liquid Fuels |
| ASTM E 563 : 1997 | Standard Practice for Preparation and Use of an Ice-Point Bath as a Reference Temperature |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.