ASTM D 7808 : 2018
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Practice for Determining the Site Precision of a Process Stream Analyzer on Process Stream Material
Hardcopy , PDF
06-28-2022
English
08-24-2018
Important note : All end users must be registered with an Account prior to user licenses being assigned.This practice describes a procedure to quantify the site precision of a process analyzer via repetitive measurement of a single process sample over an extended time period.
| Committee |
D 02
|
| DocumentType |
Standard Practice
|
| Pages |
5
|
| ProductNote |
ASTM D7808:2018 THIS STANDARD ALSO REFERS TO ASTM D 6299-18
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This practice describes a procedure to quantify the site precision of a process analyzer via repetitive measurement of a single process sample over an extended time period. The procedure may be applied to multiple process samples to obtain site precision estimates at different property levels
1.1.1The site precision is required for use of the statistical methodology of D6708 in establishing the correlation between analyzer results and primary test method results using Practice D7235.
1.1.2The site precision is also required when employing the statistical methodology of D6708 to validate a process analyzer via Practices D3764 or D6122.
1.2This practice is not applicable to in-line analyzers where the same quality control sample cannot be repetitively introduced.
1.3This practice is meant to be applied to analyzers that measure physical properties or compositions.
1.4This practice can be applied to any process analyzer system where the feed stream can be captured and stored in sufficient quantity with no stratification or stability concerns.
1.4.1The captured stream sample introduction must be able to meet the process analyzer sample conditioning requirements, feed temperature and inlet pressure.
1.4.2This practice is designed for use with samples that are single liquid phase, petroleum products whose vapor pressure, at sampling and sample storage conditions, is less than or equal to 110 kPa (16.0 psi) absolute and whose D86 final boiling point is less than or equal to 400 °C (752 °F).
Note 1:The general procedures described in this practice may be applicable to materials outside this range, including multiphase materials, but such application may involve special sampling and safety considerations which are outside the scope of this practice.
1.5The values for operating conditions are stated in SI units and are to be regarded as the standard. The values given in parentheses are the historical inch-pound units for information only.
1.6This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.7This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM D 7235 : 2016 | Standard Guide for Establishing a Linear Correlation Relationship Between Analyzer and Primary Test Method Results Using Relevant ASTM Standard Practices |
| ASTM D 8094 : 2021 | Standard Test Method for Determination of Water Content of Liquefied Petroleum Gases (LPG) Using an Online Electronic Moisture Analyzer |
| ASTM D 8340 : 2021 | Standard Practice for Performance-Based Qualification of Spectroscopic Analyzer Systems |
| ASTM D 7825 : 2018 | Standard Practice for Generating a Process Stream Property Value through Application of a Process Stream Analyzer |
| ASTM D 7235 : 2021 : REV A | Standard Guide for Establishing a Linear Correlation Relationship Between Analyzer and Primary Test Method Results Using Relevant ASTM Standard Practices |
| ASTM D 6122 : 2021 | Standard Practice for Validation of the Performance of Multivariate Online, At-Line, Field and Laboratory Infrared Spectrophotometer, and Raman Spectrometer Based Analyzer Systems |
| ASTM D 6299 : 2010 | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
| ASTM D 6299 : 2013 : EDT 1 | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
| ASTM D 6708 : 2018 | Standard Practice for Statistical Assessment and Improvement of Expected Agreement Between Two Test Methods that Purport to Measure the Same Property of a Material |
| ASTM D 6708 : 2015 | Standard Practice for Statistical Assessment and Improvement of Expected Agreement Between Two Test Methods that Purport to Measure the Same Property of a Material |
| ASTM D 6708 : 2013 | Standard Practice for Statistical Assessment and Improvement of Expected Agreement Between Two Test Methods that Purport to Measure the Same Property of a Material |
| ASTM D 6122 : 2010 | Standard Practice for Validation of the Performance of Multivariate Online, At-Line, and Laboratory Infrared Spectrophotometer Based Analyzer Systems |
| ASTM D 7235 : 2010 | Standard Guide for Establishing a Linear Correlation Relationship Between Analyzer and Primary Test Method Results Using Relevant ASTM Standard Practices |
| ASTM D 6299 : 2017 : REV A | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
| ASTM D 6122 : 2020 : REV A | Standard Practice for Validation of the Performance of Multivariate Online, At-Line, Field and Laboratory Infrared Spectrophotometer, and Raman Spectrometer Based Analyzer Systems |
| ASTM D 6299 : 2017 : REV B | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
| ASTM D 3764 : 2013 | Standard Practice for Validation of the Performance of Process Stream Analyzer Systems |
| ASTM D 6299 : 2009 | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
| ASTM D 6122 : 2013 | Standard Practice for Validation of the Performance of Multivariate Online, At-Line, and Laboratory Infrared Spectrophotometer Based Analyzer Systems |
| ASTM D 6708 : 2007 | Standard Practice for Statistical Assessment and Improvement of Expected Agreement Between Two Test Methods that Purport to Measure the Same Property of a Material |
| ASTM D 6299 : 2013 | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
| ASTM D 6122 : 2006 | Standard Practice for Validation of the Performance of Multivariate Process Infrared Spectrophotometers |
| ASTM D 3764 : 2015 : EDT 1 | Standard Practice for Validation of the Performance of Process Stream Analyzer Systems |
| ASTM D 6299 : 2021 | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
| ASTM D 3764 : 2001 | Standard Practice for Validation of Process Stream Analyzer Systems |
| ASTM D 6708 : 2016 : REV B | Standard Practice for Statistical Assessment and Improvement of Expected Agreement Between Two Test Methods that Purport to Measure the Same Property of a Material |
| ASTM D 6299 : 2010 : EDT 1 | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
| ASTM D 6708 : 2006 | Standard Practice for Statistical Assessment and Improvement of Expected Agreement Between Two Test Methods that Purport to Measure the Same Property of a Material |
| ASTM D 3764 : 2006 | Standard Practice for Validation of the Performance of Process Stream Analyzer Systems |
| ASTM D 6122 : 2015 | Standard Practice for Validation of the Performance of Multivariate Online, At-Line, and Laboratory Infrared Spectrophotometer Based Analyzer Systems |
| ASTM D 7235 : 2014 | Standard Guide for Establishing a Linear Correlation Relationship Between Analyzer and Primary Test Method Results Using Relevant ASTM Standard Practices |
| ASTM D 3764 : 1992 : R1998 | Standard Practice for Validation of Process Stream Analyzer Systems |
| ASTM D 6708 : 2004 | Standard Practice for Statistical Assessment and Improvement of the Expected Agreement Between Two Test Methods that Purport to Measure the Same Property of a Material |
| ASTM D 6708 : 2019 | Standard Practice for Statistical Assessment and Improvement of Expected Agreement Between Two Test Methods that Purport to Measure the Same Property of a Material |
| ASTM D 6708 : 2016 : REV A | Standard Practice for Statistical Assessment and Improvement of Expected Agreement Between Two Test Methods that Purport to Measure the Same Property of a Material |
| ASTM D 6708 : 2008 | Standard Practice for Statistical Assessment and Improvement of Expected Agreement Between Two Test Methods that Purport to Measure the Same Property of a Material |
| ASTM D 6122 : 2001 | Standard Practice for Validation of Multivariate Process Infrared Spectrophotometers |
| ASTM D 6299 : 2000 | Standard Practice for Applying Statistical Quality Assurance Techniques to Evaluate Analytical Measurement System Performance |
| ASTM D 6299 : 2010 : EDT 2 | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
| ASTM D 6299 : 2016 | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
| ASTM D 6122 : 2019 : REV A | Standard Practice for Validation of the Performance of Multivariate Online, At-Line, and Laboratory Infrared Spectrophotometer Based Analyzer Systems |
| ASTM D 6122 : 2018 | Standard Practice for Validation of the Performance of Multivariate Online, At-Line, and Laboratory Infrared Spectrophotometer Based Analyzer Systems |
| ASTM D 7235 : 2016 | Standard Guide for Establishing a Linear Correlation Relationship Between Analyzer and Primary Test Method Results Using Relevant ASTM Standard Practices |
| ASTM D 6299 : 2019 | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
| ASTM D 6299 : 2000 : REV A | Standard Practice for Applying Statistical Quality Assurance Techniques to Evaluate Analytical Measurement System Performance |
| ASTM D 6708 : 2001 | Standard Practice for Statistical Assessment and Improvement of the Expected Agreement Between Two Test Methods that Purport to Measure the Same Property of a Material |
| ASTM D 6708 : 2021 | Standard Practice for Statistical Assessment and Improvement of Expected Agreement Between Two Test Methods that Purport to Measure the Same Property of a Material |
| ASTM D 7235 : 2021 | Standard Guide for Establishing a Linear Correlation Relationship Between Analyzer and Primary Test Method Results Using Relevant ASTM Standard Practices |
| ASTM D 6299 : 2020 | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
| ASTM D 6708 : 2001 : EDT 1 | Standard Practice for Statistical Assessment and Improvement of the Expected Agreement Between Two Test Methods that Purport to Measure the Same Property of a Material |
| ASTM D 6299 : 2008 | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
| ASTM D 7235 : 2005 | Standard Guide for Establishing a Linear Correlation Relationship Between Analyzer and Primary Test Method Results Using Relevant ASTM Standard Practices |
| ASTM D 7235 : 2021 : REV A | Standard Guide for Establishing a Linear Correlation Relationship Between Analyzer and Primary Test Method Results Using Relevant ASTM Standard Practices |
| ASTM D 6708 : 2005 | Standard Practice for Statistical Assessment and Improvement of the Expected Agreement Between Two Test Methods that Purport to Measure the Same Property of a Material |
| ASTM D 3764 : 2015 | Standard Practice for Validation of the Performance of Process Stream Analyzer Systems |
| ASTM D 6708 : 2013 : EDT 1 | Standard Practice for Statistical Assessment and Improvement of Expected Agreement Between Two Test Methods that Purport to Measure the Same Property of a Material |
| ASTM D 6299 : 2002 : EDT 1 | Standard Practice for Applying Statistical Quality Assurance Techniques to Evaluate Analytical Measurement System Performance |
| ASTM D 6708 : 2016 | Standard Practice for Statistical Assessment and Improvement of Expected Agreement Between Two Test Methods that Purport to Measure the Same Property of a Material |
| ASTM D 7278 : 2021 | Standard Guide for Prediction of Analyzer Sample System Lag Times |
| ASTM D 3764 : 2009 | Standard Practice for Validation of the Performance of Process Stream Analyzer Systems |
| ASTM D 6122 : 2019 | Standard Practice for Validation of the Performance of Multivariate Online, At-Line, and Laboratory Infrared Spectrophotometer Based Analyzer Systems |
| ASTM D 7278 : 2011 | Standard Guide for Prediction of Analyzer Sample System Lag Times |
| ASTM D 6299 : 2022 | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
| ASTM D 7278 : 2016 | Standard Guide for Prediction of Analyzer Sample System Lag Times |
| ASTM D 6122 : 2006 : EDT 1 | Standard Practice for Validation of the Performance of Multivariate Process Infrared Spectrophotometers |
| ASTM D 7278 : 2006 | Standard Guide for Prediction of Analyzer Sample System Lag Times |
| ASTM D 6708 : 2019 : REV A | Standard Practice for Statistical Assessment and Improvement of Expected Agreement Between Two Test Methods that Purport to Measure the Same Property of a Material |
| ASTM D 6122 : 1999 | Standard Practice for Validation of Multivariate Process Infrared Spectrophotometers |
| ASTM D 6299 : 2007 | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
| ASTM D 6299 : 2007 : EDT 1 | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
| ASTM D 6299 : 2020 : REV A | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
| ASTM D 6299 : 2017 | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
| ASTM D 6708 : 2019 : REV A : EDT 1 | Standard Practice for Statistical Assessment and Improvement of Expected Agreement Between Two Test Methods that Purport to Measure the Same Property of a Material |
| ASTM D 6122 : 2009 | Standard Practice for Validation of the Performance of Multivariate Process Infrared Spectrophotometers |
| ASTM D 6299 : 2002 | Standard Practice for Applying Statistical Quality Assurance Techniques to Evaluate Analytical Measurement System Performance |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.