ASTM D 7745 : 2011
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Practice for Testing Pultruded Composites
Hardcopy , PDF
01-10-2020
English
09-01-2011
Important note : All end users must be registered with an Account prior to user licenses being assigned.CONTAINED IN VOL. 08.03, 2015 Describes the test methods commonly used for pultruded composites.
| Committee |
D 20
|
| DocumentType |
Standard Practice
|
| Pages |
2
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy |
1.1 This protocol summarizes the applicable ASTM and other standard test methods commonly used for pultruded composites. The individual performance requirements to these test methods are defined by specific customer specifications.
1.2 This protocol also defines appropriate specimen locations for sampling from the pultruded composites.
1.3 This protocol does not discuss all possible standard test methods that may be utilized for pultruded composites.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Note 1—There is no known ISO equivalent to this guide.
| ASTM D 7792/D7792M : 2015 | Standard Practice for Freeze/Thaw Conditioning of Pultruded Fiber Reinforced Polymer (FRP) Composites Used in Structural Designs |
| ASTM D 7992/D7992M : 2015 | Standard Practice for Elevated Temperature and Moisture Conditioning of Pultruded Fiber Reinforced Polymer (FRP) Composites Used in Structural Designs |
| ASTM D 7136/D7136M : 2015 : REDLINE | Standard Test Method for Measuring the Damage Resistance of a Fiber-Reinforced Polymer Matrix Composite to a Drop-Weight Impact Event |
| ASTM D 495 : 2014 | Standard Test Method for High-Voltage, Low-Current, Dry Arc Resistance of Solid Electrical Insulation |
| ASTM D 5420 : 1998 : REV A | Standard Test Method for Impact Resistance of Flat, Rigid Plastic Specimen by Means of a Striker Impacted by a Falling Weight (Gardner Impact) |
| ASTM D 2583 : 2013 : REV A | Standard Test Method for Indentation Hardness of Rigid Plastics by Means of a Barcol Impressor (Withdrawn 2022) |
| ASTM D 4065 : 2006 | Standard Practice for Plastics: Dynamic Mechanical Properties: Determination and Report of Procedures |
| ASTM D 3918 : 2011 : REDLINE | Standard Terminology Relating to Reinforced Plastic Pultruded Products |
| ASTM D 5420 : 2010 | Standard Test Method for Impact Resistance of Flat, Rigid Plastic Specimen by Means of a Striker Impacted by a Falling Weight (Gardner Impact) |
| ASTM D 2584 : 2002 | Standard Test Method for Ignition Loss of Cured Reinforced Resins |
| ASTM D 2584 : 2008 | Standard Test Method for Ignition Loss of Cured Reinforced Resins |
| ASTM D 2584 : 1994 | Standard Test Method for Ignition Loss of Cured Reinforced Resins |
| ASTM D 2583 : 2006 | Standard Test Method for Indentation Hardness of Rigid Plastics by Means of a Barcol Impressor |
| ASTM D 5420 : 2004 | Standard Test Method for Impact Resistance of Flat, Rigid Plastic Specimen by Means of a Striker Impacted by a Falling Weight (Gardner Impact) |
| ASTM D 2344/D2344M : 2016 : REDLINE | Standard Test Method for Short-Beam Strength of Polymer Matrix Composite Materials and Their Laminates |
| ASTM D 792 : 2013 : REDLINE | Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement |
| ASTM D 5379/D5379M : 2012 : REDLINE | Standard Test Method for Shear Properties of Composite Materials by the V-Notched Beam Method |
| ASTM D 2583 : 2013 | Standard Test Method for Indentation Hardness of Rigid Plastics by Means of a Barcol Impressor |
| ASTM D 2584 : 2011 | Standard Test Method for Ignition Loss of Cured Reinforced Resins |
| ASTM D 3916 : 2002 | Standard Test Method for Tensile Properties of Pultruded Glass-Fiber-Reinforced Plastic Rod |
| ASTM D 4065 : 2012 | Standard Practice for Plastics: Dynamic Mechanical Properties: Determination and Report of Procedures |
| ASTM D 3916 : 2008 | Standard Test Method for Tensile Properties of Pultruded Glass-Fiber-Reinforced Plastic Rod |
| ASTM G 154 : 2016 : REDLINE | Standard Practice for Operating Fluorescent Ultraviolet (UV) Lamp Apparatus for Exposure of Nonmetallic Materials |
| ASTM D 696 : 2016 : REDLINE | Standard Test Method for Coefficient of Linear Thermal Expansion of Plastics Between −30°C and 30°C with a Vitreous Silica Dilatometer |
| ASTM D 3918 : 1996 | Standard Terminology Relating to Reinforced Plastic Pultruded Products |
| ASTM D 790 : 2017 : REDLINE | Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials |
| ASTM D 2584 : 1968 | Standard Method Of Test For Ignition Loss Of Cured Reinforced Resins |
| ASTM D 3916 : 1994 | Standard Test Method for Tensile Properties of Pultruded Glass-Fiber-Reinforced Plastic Rod |
| ASTM D 3918 : 2011 | Standard Terminology Relating to Reinforced Plastic Pultruded Products (Withdrawn 2020) |
| ASTM D 5420 : 2016 : REDLINE | Standard Test Method for Impact Resistance of Flat, Rigid Plastic Specimen by Means of a Striker Impacted by a Falling Weight (Gardner Impact) |
| ASTM D 4065 : 2012 : REDLINE | Standard Practice for Plastics: Dynamic Mechanical Properties: Determination and Report of Procedures |
| ASTM D 2584 : 2018 | Standard Test Method for Ignition Loss of Cured Reinforced Resins |
| ASTM D 3039/D3039M : 2017 : REDLINE | Standard Test Method for Tensile Properties of Polymer Matrix Composite Materials |
| ASTM D 4065 : 1995 | Standard Practice for Plastics: Dynamic Mechanical Properties: Determination and Report of Procedures |
| ASTM D 5420 : 2016 | Standard Test Method for Impact Resistance of Flat, Rigid Plastic Specimen by Means of a Striker Impacted by a Falling Weight (Gardner Impact) |
| ASTM D 7332/D7332M : 2016 : REDLINE | Standard Test Method for Measuring the Fastener Pull-Through Resistance of a <brk/>Fiber-Reinforced Polymer Matrix Composite |
| ASTM D 695 : 2015 : REDLINE | Standard Test Method for Compressive Properties of Rigid Plastics |
| ASTM D 570 : 1998 : R2018 | Standard Test Method for Water Absorption of Plastics |
| ASTM D 2583 : 2007 | Standard Test Method for Indentation Hardness of Rigid Plastics by Means of a Barcol Impressor |
| ASTM D 638 : 2014 : REDLINE | Standard Test Method for Tensile Properties of Plastics |
| ASTM D 3916 : 2008 : R2016 | Standard Test Method for Tensile Properties of Pultruded Glass-Fiber-Reinforced<brk /> Plastic Rod |
| ASTM D 2583 : 1995 | Standard Test Method for Indentation Hardness of Rigid Plastics by Means of a Barcol Impressor |
| ASTM D 4065 : 2001 | Standard Practice for Plastics: Dynamic Mechanical Properties: Determination and Report of Procedures |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.