ASTM D 7684 : 2011 : R2016
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Guide for Microscopic Characterization of Particles from In-Service Lubricants
Hardcopy , PDF
12-01-2020
English
11-21-2016
Important note : All end users must be registered with an Account prior to user licenses being assigned.This guide covers the classification and reporting of results from in-service lubricant particulate debris analysis obtained by microscopic inspection of wear and contaminant particles extracted from in-service lubricant and hydraulic oil samples.
| Committee |
D 02
|
| DocumentType |
Guide
|
| Pages |
9
|
| ProductNote |
Reconfirmed 2016
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This guide covers the classification and reporting of results from in-service lubricant particulate debris analysis obtained by microscopic inspection of wear and contaminant particles extracted from in-service lubricant and hydraulic oil samples. This guide suggests standardized terminology to promote consistent reporting, provides logical framework to document likely or possible root causes, and supports inference associated machinery health condition or severity based on available debris analysis information.
1.2This guide shall be used in conjunction with an appropriate wear debris analysis sample preparation and inspection technique including, but not limited to, one of the following:
1.2.1Ferrography using linear glass slides,
1.2.2Ferrography using rotary glass slides,
1.2.3Patch analysis using patch makers (filtration through membrane filters),
1.2.4Filter debris analysis,
1.2.5Magnetic plug inspection, or
1.2.6Other means used to extract and inspect particulate debris from in-service lubricants.
1.3This standard is not intended to evaluate or characterize the advantage or disadvantage of one or another of these particular particle extraction and inspection methods.
1.4The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| ASTM D 7720 : 2011 : R2017 | Standard Guide for Statistically Evaluating Measurand Alarm Limits when Using Oil Analysis to Monitor Equipment and Oil for Fitness and Contamination |
| ASTM D 7690 : 2011 : R2017 | Standard Practice for Microscopic Characterization of Particles from In-Service Lubricants by Analytical Ferrography |
| ASTM D 7919 : 2014 : R2017 | Standard Guide for Filter Debris Analysis (FDA) Using Manual or Automated Processes |
| ASTM D 7898 : 2014 | Standard Practice for Lubrication and Hydraulic Filter Debris Analysis (FDA) for Condition Monitoring of Machinery |
| ASTM D 4175 : 2020 | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 4175 : 2014 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 4175 : 2009 : REV A : EDT 1 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 4175 : 2008 : REV B : EDT 1 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 4175 : 2005 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 4175 : 2005 : EDT 2 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 4175 : 2015 : REV C | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 7596 : 2014 | Standard Test Method for Automatic Particle Counting and Particle Shape Classification of Oils Using a Direct Imaging Integrated Tester |
| ASTM D 4130 : 2015 : REDLINE | Standard Test Method for Sulfate Ion in Brackish Water, Seawater, and Brines |
| ASTM D 4175 : 2017 : REV A : EDT 1 | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 7416 : 2009 : R2020 | Standard Practice for Analysis of In-Service Lubricants Using a Particular Five-Part (Dielectric Permittivity, Time-Resolved Dielectric Permittivity with Switching Magnetic Fields, Laser Particle Counter, Microscopic Debris Analysis, and Orbital Viscometer) Integrated Tester |
| ASTM D 7416 : 2009 | Standard Practice for Analysis of In-Service Lubricants Using a Particular Five-Part (Dielectric Permittivity, Time-Resolved Dielectric Permittivity with Switching Magnetic Fields, Laser Particle Counter, Microscopic Debris Analysis, and Orbital Viscome |
| ASTM D 4175 : 2008 : REV A | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 4175 : 2020 : REV A | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 7596 : 2014 : REDLINE | Standard Test Method for Automatic Particle Counting and Particle Shape Classification of Oils Using a Direct Imaging Integrated Tester |
| ASTM D 4175 : 2017 : REV B | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 4175 : 2009 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 4175 : 2009 : REV A : EDT 4 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 4175 : 2009 : REV A : EDT 3 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 4130 : 2008 | Standard Test Method for Sulfate Ion in Brackish Water, Seawater, and Brines |
| ASTM D 4175 : 2018 | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 4130 : 1999 | Standard Test Method for Sulfate Ion in Brackish Water, Seawater, and Brines |
| ASTM D 7416 : 2008 | Standard Practice for Analysis of In-Service Lubricants Using a Particular Five-Part (Dielectric Permittivity, Time-Resolved Dielectric Permittivity with Switching Magnetic Fields, Laser Particle Counter, Microscopic Debris Analysis, and Orbital Viscome |
| ASTM D 4175 : 2001 : EDT 1 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 4175 : 2001 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 4175 : 2005 : EDT 1 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 7690 : 2011 : R2017 | Standard Practice for Microscopic Characterization of Particles from In-Service Lubricants by Analytical Ferrography |
| ASTM D 4175 : 2002 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 4175 : 2015 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 4175 : 2002 : REV A : EDT 2 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 7647 : 2010 : R2018 | Standard Test Method for Automatic Particle Counting of Lubricating and Hydraulic Fluids Using Dilution Techniques to Eliminate the Contribution of Water and Interfering Soft Particles by Light Extinction |
| ASTM D 7647 : 2010 | Standard Test Method for Automatic Particle Counting of Lubricating and Hydraulic Fluids Using Dilution Techniques to Eliminate the Contribution of Water and Interfering Soft Particles by Light Extinction |
| ASTM D 4175 : 2009 : REV A : EDT 5 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 4175 : 2016 : REV C | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 4175 : 2015 : REV B | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 4175 : 2015 : REV A | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 4175 : 2009 : REV A | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 4175 : 2016 : REV B | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 4175 : 2002 : REV A : EDT 1 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 4175 : 2008 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 4175 : 2002 : REV A | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 4175 : 2000 : EDT 1 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 4175 : 2016 : REV A | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 7690 : 2011 | Standard Practice for Microscopic Characterization of Particles from In-Service Lubricants by Analytical Ferrography |
| ASTM D 4130 : 2015 | Standard Test Method for Sulfate Ion in Brackish Water, Seawater, and Brines (Withdrawn 2024) |
| ISO 11171:2016 | Hydraulic fluid power Calibration of automatic particle counters for liquids |
| ASTM D 4175 : 2019 : EDT 1 | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 7416 : 2009 : R2015 | Standard Practice for Analysis of In-Service Lubricants Using a Particular Five-Part (Dielectric Permittivity, Time-Resolved Dielectric Permittivity with Switching Magnetic Fields, Laser Particle Counter, Microscopic Debris Analysis, and Orbital Viscometer) Integrated Tester |
| ASTM D 4175 : 2017 : REV A | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 4130 : 1982 : R1998 | Standard Test Method for Sulfate Ion in Brackish Water, Seawater, and Brines |
| ASTM D 4175 : 2009 : REV A : EDT 2 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 4175 : 2018 : EDT 1 | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 4175 : 2016 | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 7596 : 2010 | Standard Test Method for Automatic Particle Counting and Particle Shape Classification of Oils Using a Direct Imaging Integrated Tester |
| ASTM D 4130 : 2003 | Standard Test Method for Sulfate Ion in Brackish Water, Seawater, and Brines |
| ASTM D 4175 : 2017 | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 4175 : 2019 | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 4175 : 2015 : REV B : EDT 1 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 4175 : 2008 : REV B | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.