ASTM D 7596 : 2014 : REDLINE
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Automatic Particle Counting and Particle Shape Classification of Oils Using a Direct Imaging Integrated Tester
03-17-2023
English
12-16-2019
Important note : All end users must be registered with an Account prior to user licenses being assigned.CONTAINED IN VOL. 05.04, 2018 Defines the determination of particle concentration, particle size distribution, particle shape, and soot content for new and in-service oils used for lubrication and hydraulic systems by a direct imaging integrated tester.
| Committee |
D 02
|
| DocumentType |
Redline
|
| Pages |
7
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy |
1.1This test method covers the determination of particle concentration, particle size distribution, particle shape, and soot content for new and in-service oils used for lubrication and hydraulic systems by a direct imaging integrated tester.
1.1.1The test method is applicable to petroleum and synthetic based fluids. Samples from 2 to 150 mm2/s at 40°C may be processed directly. Samples of greater viscosity may be processed after solvent dilution.
1.1.2Particles measured are in the range from 4 μm to ≥ 70 μm with the upper limit dependent upon passing through a 100 μm mesh inlet screen.
1.1.3Particle concentration measured may be as high as 5 000 000 particles per mL without significant coincidence error.
1.1.4Particle shape is determined for particles greater than approximately 20 µm in length. Particles are categorized into the following categories: sliding, cutting, fatigue, nonmetallic, fibers, water droplets, and air bubbles.
1.1.5Soot is determined up to approximately 1.5 % by weight.
1.1.6This test method uses objects of known linear dimension for calibration.
1.2The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| SAE AIR 1828 : 2014 | GUIDE TO ENGINE LUBRICATION SYSTEM MONITORING |
| ASTM D 7720 : 2011 : R2017 | Standard Guide for Statistically Evaluating Measurand Alarm Limits when Using Oil Analysis to Monitor Equipment and Oil for Fitness and Contamination |
| ASTM D 7684 : 2011 | Standard Guide for Microscopic Characterization of Particles from In-Service Lubricants |
| ASTM D 8128 : 2017 | Standard Guide for Monitoring Failure Mode Progression in Industrial Applications with Rolling Element Ball Type Bearings |
| 16/30323482 DC : 0 | BS ISO 11365 - PETROLEUM AND RELATED PRODUCTS - MAINTENANCE AND USE GUIDE FOR TRIARYL PHOSPHATE ESTER TURBINE CONTROL FLUIDS |
| ISO 11365:2017 | Petroleum and related products — Requirements and guidance for the maintenance of triaryl phosphate ester turbine control fluids |
| BS ISO 11365:2017 | Petroleum and related products. Requirements and guidance for the maintenance of triaryl phosphate ester turbine control fluids |
| ASTM D 7720:2011 | Standard Guide for Statistically Evaluating Measurand Alarm Limits when Using Oil Analysis to Monitor Equipment and Oil for Fitness and Contamination |
| ASTM D 7684 : 2011 : R2016 | Standard Guide for Microscopic Characterization of Particles from In-Service Lubricants |
| ASTM D 6595 : 2017 : REDLINE | Standard Test Method for Determination of Wear Metals and Contaminants in Used Lubricating Oils or Used Hydraulic Fluids by Rotating Disc Electrode Atomic Emission Spectrometry |
| ASTM D 2896 : 2015 : REDLINE | Standard Test Method for Base Number of Petroleum Products by Potentiometric Perchloric Acid Titration |
| ASTM D 5967 : 2017 : REDLINE | Standard Test Method for Evaluation of Diesel Engine Oils in T-8 Diesel Engine |
| ASTM E 2412 : 2010 | Standard Practice for Condition Monitoring of Used Lubricants by Trend Analysis Using Fourier Transform Infrared (FT-IR) Spectrometry |
| SAE AS 4059F : 2013 | AEROSPACE FLUID POWER - CONTAMINATION CLASSIFICATION FOR HYDRAULIC FLUIDS |
| ISO 12103-1:2016 | Road vehicles — Test contaminants for filter evaluation — Part 1: Arizona test dust |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.