ASTM D 746 : 2024
Current
The latest, up-to-date edition.
Standard Test Method for Brittleness Temperature of Plastics and Elastomers by Impact
Hardcopy , PDF
English
06-12-2024
Committee |
D 20
|
DocumentType |
Test Method
|
Pages |
8
|
PublisherName |
American Society for Testing and Materials
|
Status |
Current
|
Supersedes |
1.1This test method covers the determination of the temperature at which plastics and elastomers (as defined by Terminology D883) exhibit brittle failure under specified impact conditions. Two routine inspection and acceptance procedures are also provided.
Note 1:When testing rubbers for impact brittleness use Test Method D2137. When testing plastic sheeting for impact brittleness, use Test Method D1790.
1.2The values stated in SI units are to be regarded as the standard.
1.3Due to the potential safety and environmental hazards associated with mercury-filled thermometers, the use of alternative temperature measuring devices (such as thermocouples and RTDs) is encouraged.
Warning—Mercury has been designated by many regulatory agencies as a hazardous material that can cause serious medical issues. Mercury, or its vapor, has been demonstrated to be hazardous to health and corrosive to materials. Caution should be taken when handling mercury and mercury containing products. See the applicable product Safety Data Sheet (SDS) for additional information. Users should be aware that selling mercury and/or mercury containing products into your state or country may be prohibited by law.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
Note 2:This test method and ISO 974 address the same subject matter, but differ in technical content.
1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM D 3847 : 2001 : R2018 | Standard Practice for Rubber—Directions for Achieving Subnormal Test Temperatures |
ASTM C 542 : 2005 : R2017 | Standard Specification for Lock-Strip Gaskets |
ASTM D 5926 : 2015 : R2020 | Standard Specification for Poly (Vinyl Chloride) (PVC) Gaskets for Drain, Waste, and Vent (DWV), Sewer, Sanitary, and Storm Plumbing Systems |
ASTM F 790 : 2023 | Standard Guide for Testing Materials for Aerospace Plastic Transparent Enclosures |
ASTM D 6134/D6134M : 2007 : R2024 | Standard Specification for Vulcanized Rubber Sheets Used in Waterproofing Systems |
ASTM C 864 : 2005 : R2019 | Standard Specification for Dense Elastomeric Compression Seal Gaskets, Setting Blocks, and Spacers |
ASTM F 2510/F2510M : 2022 | Standard Specification for Resilient Connectors Between Reinforced Concrete Manhole Structures and Corrugated Dual- and Triple-Wall Polyethylene and Polypropylene Pipes |
ASTM E 1783/E1783M : 2024 | Standard Specification for Preformed Architectural Strip Seals for Buildings and Parking Structures |
ASTM D 3105 : 2017 : R2024 | Standard Index of Methods for Testing Elastomeric and Plastomeric Roofing and Waterproofing Materials |
ASTM D 2647 : 2018 : R2024 | Standard Specification for Crosslinkable Ethylene Plastics |
ASTM D 6434 : 2012 : R2018 | Standard Guide for the Selection of Test Methods for Flexible Polypropylene Geomembranes |
ASTM A 975 : 2023 | Standard Specification for Double-Twisted Hexagonal Mesh Gabions and Revet Mattresses (Metallic-Coated Steel Wire or Metallic-Coated Steel Wire With Poly(Vinyl Chloride) (PVC) Coating) |
ASTM D 876 : 2021 | Standard Test Methods for Nonrigid Vinyl Chloride Polymer Tubing Used for Electrical Insulation |
ASTM D 2287 : 2019 | Standard Classification System and Basis for Specification for Nonrigid Vinyl Chloride Polymer and Copolymer Molding and Extrusion Compounds |
ASTM A 974 : 1997 : R2021 | Standard Specification for Welded Wire Fabric Gabions and Gabion Mattresses (Metallic-Coated or Polyvinyl Chloride (PVC) Coated) |
ASTM F 3123 : 2022 | Standard Specification for Metric Outside Diameter Polyethylene (PE) Plastic Pipe (DR-PN) |
ASTM D 2671 : 2021 | Standard Test Methods for Heat-Shrinkable Tubing for Electrical Use |
ASTM A 1107/A1107M : 2017 : R2022 | Standard Specification for Resilient Connectors Between Reinforced Concrete Manhole Structures and Corrugated Steel Drainage Pipes |
ASTM E 2203 : 2014 : R2018 | Standard Specification for Dense Thermoplastic Elastomers Used for Compression Seals, Gaskets, Setting Blocks, Spacers and Accessories |
ASTM D 350 : 2021 | Standard Test Methods for Flexible Treated Sleeving Used for Electrical Insulation |
ASTM D 5721 : 2022 | Standard Practice for Air-Oven Aging of Polyolefin Geomembranes |
ASTM D 1248 : 2016 | Standard Specification for Polyethylene Plastics Extrusion Materials for Wire and Cable |
ASTM D 6455 : 2011 : R2018 | Standard Guide for the Selection of Test Methods for Prefabricated Bituminous Geomembranes (PBGMs) |
ASTM D 3350 : 2021 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
ASTM C 1644 : 2006 : R2017 | Standard Specification for Resilient Connectors Between Reinforced Concrete On-Site Wastewater Tanks and Pipes |
ASTM E 1612/E1612M : 1994 : R2022 | Standard Specification for Preformed Architectural Compression Seals for Buildings and Parking Structures |
ASTM D 4101 : 2024 | Standard Classification System and Basis for Specification for Polypropylene Injection and Extrusion Materials |
ASTM C 509 : 2006 : R2021 | Standard Specification for Elastomeric Cellular Preformed Gasket and Sealing<brk/> Material |
ASTM D 883 : 2024 : REV A | Standard Terminology Relating to Plastics |
ASTM D 883 : 2024 | Standard Terminology Relating to Plastics |
ASTM D 832 : 2007 : R2024 | Standard Practice for Rubber Conditioning For Low Temperature Testing |
ASTM D 832 : 2007 : R2018 | Standard Practice for Rubber Conditioning For Low Temperature Testing |
ASTM E 608/E608M : 2024 | Standard Specification for Mineral-Insulated, Metal-Sheathed Base Metal Thermocouples |
ASTM E 608/E608M : 2013 : R2019 | Standard Specification for Mineral-Insulated, Metal-Sheathed Base Metal Thermocouples |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.