ASTM D 7319 : 2017 : REDLINE
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Determination of Existent and Potential Sulfate and Inorganic Chloride in Fuel Ethanol and Butanol by Direct Injection Suppressed Ion Chromatography
10-18-2022
English
10-06-2017
Important note : All end users must be registered with an Account prior to user licenses being assigned.CONTAINED IN VOL. 05.04, 2018 Defines a direct injection ion chromatographic procedure for determining the total and potential inorganic sulfate and total inorganic chloride content in hydrous and anhydrous denatured ethanol to be used in motor fuel applications.
| Committee |
D 02
|
| DocumentType |
Redline
|
| Pages |
10
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy |
1.1This test method covers a direct injection ion chromatographic procedure for determining existent and potential inorganic sulfate and total inorganic chloride content in hydrous and anhydrous denatured ethanol and butanol to be used in motor fuel applications. It is intended for the analysis of ethanol and butanol samples containing between 1.0 mg/kg to 20 mg/kg of existent or potential inorganic sulfate and 1.0 mg/kg to 50 mg/kg of inorganic chloride.
Note 1:Tertiary butanol is not included in this test method. 1-butanol, 2-butanol, and isobutanol are included in the testing and research report for this test method.
1.2The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Material Safety Data Sheets are available for reagents and materials. Review them for hazards prior to usage.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM D 8076 : 2017 : REV A | Standard Specification for 100 Research Octane Number Test Fuel for Automotive Spark-Ignition Engines |
| ASTM D 7578 : 2015-06 | GUIDE FOR CALIBRATION REQUIREMENTS FOR ELEMENTAL ANALYSIS OF PETROLEUM PRODUCTS AND LUBRICANTS |
| ASTM D 8076 : 2017 | Standard Specification for 100 Research Octane Number Test Fuel for Automotive Spark-Ignition Engines |
| ASTM D 7328 : 2017 : REDLINE | Standard Test Method for Determination of Existent and Potential Inorganic Sulfate and Total Inorganic Chloride in Fuel Ethanol by Ion Chromatography Using Aqueous Sample Injection |
| ASTM D 8149 : 2017 | Standard Practice for Optimization, Calibration, and Validation of Ion Chromatographic Determination of Heteroatoms and Anions in Petroleum Products and Lubricants |
| ASTM D 7328 : 2017 : REDLINE | Standard Test Method for Determination of Existent and Potential Inorganic Sulfate and Total Inorganic Chloride in Fuel Ethanol by Ion Chromatography Using Aqueous Sample Injection |
| ASTM D 6792 : 2017 : REDLINE | Standard Practice for Quality Management Systems in Petroleum Products, Liquid Fuels, and Lubricants Testing Laboratories |
| EN 15492:2012 | Ethanol as a blending component for petrol - Determination of inorganic chloride and sulfate content - Ion chromatographic method |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.