ASTM D 7254 : 2021
Current
The latest, up-to-date edition.
Standard Specification for Polypropylene (PP) Siding
Hardcopy , PDF
English
12-07-2021
Committee |
D 20
|
DocumentType |
Standard
|
Pages |
8
|
PublisherName |
American Society for Testing and Materials
|
Status |
Current
|
Supersedes |
1.1This specification establishes requirements and test methods for materials, impact strength, appearance, surface flame spread, and wind load resistance of siding products manufactured from polypropylene material. Methods of indicating compliance with this specification are also provided.
1.2The use of polypropylene recycled plastic in this product shall be in accordance with the requirements in Section 4.
1.3Siding produced to this specification shall be installed in accordance with manufacturer’s installation instructions for the specific product to be installed.
Note 1:Information with regard to siding maintenance shall be obtained from the manufacturer.
1.4The values stated in inch-pound units are to be regarded as the standard. The SI units given in parentheses are for information purposes only.
1.5The following precautionary caveat pertains to the test method portion only, Section 6 of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
Note 2:There is no known ISO equivalent to this standard.
1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM D 883 : 2023 | Standard Terminology Relating to Plastics |
ASTM E 84 : 2023 : REV D | Standard Test Method for Surface Burning Characteristics of Building Materials |
ASTM D 883 : 2024 : REV A | Standard Terminology Relating to Plastics |
ASTM D 772 : 2018 | Standard Test Method for Evaluating Degree of Flaking (Scaling) of Exterior Paints |
ASTM E 84 : 2023 : REV C | Standard Test Method for Surface Burning Characteristics of Building Materials |
ASTM D 883 : 2024 | Standard Terminology Relating to Plastics |
ASTM D 772 : 2024 | Standard Test Method for Evaluating Degree of Flaking (Scaling) of Exterior Paints |
ASTM D 5206 : 2019 | Standard Test Method for Windload Resistance of Rigid Plastic Siding |
ASTM D 883 : 2022 | Standard Terminology Relating to Plastics |
ASTM D 883 : 2020 : REV B | Standard Terminology Relating to Plastics |
ASTM E 84 : 2023 | Standard Test Method for Surface Burning Characteristics of Building Materials |
ASTM E 84 : 2022 | Standard Test Method for Surface Burning Characteristics of Building Materials |
ASTM E 84 : 2024 | Standard Test Method for Surface Burning Characteristics of Building Materials |
ASTM D 3359 : 2022 | Standard Test Methods for Rating Adhesion by Tape Test |
ASTM E 631 : 2015 : R2024 | Standard Terminology of Building Constructions |
ASTM E 84 : 2021 : REV A | Standard Test Method for Surface Burning Characteristics of Building Materials |
ASTM D 5206 : 2024 | Standard Test Method for Windload Resistance of Rigid Plastic Siding |
ASTM D 1600 : 2018 | Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024) |
ASTM D 4101 : 2024 | Standard Classification System and Basis for Specification for Polypropylene Injection and Extrusion Materials |
ASTM E 631 : 2015 | Standard Terminology of Building Constructions |
ASTM D 3679 : 2021 | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
ASTM E 84 : 2023 : REV B | Standard Test Method for Surface Burning Characteristics of Building Materials |
ASTM D 3679 : 2024 | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
ASTM D 3359 : 2023 | Standard Test Methods for Rating Adhesion by Tape Test |
ASTM E 84 : 2023 : REV A | Standard Test Method for Surface Burning Characteristics of Building Materials |
ASTM D 4101 : 2017 : EDT 1 | Standard Classification System and Basis for Specification for Polypropylene Injection and Extrusion Materials |
ASTM D 3359 : 2017 | Standard Test Methods for Rating Adhesion by Tape Test |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.