ASTM D 7156 : 2017
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Evaluation of Diesel Engine Oils in the T-11 Exhaust Gas Recirculation Diesel Engine
Available format(s)
Hardcopy , PDF
Superseded date
03-08-2024
Superseded by
Language(s)
English
Published date
05-01-2017
Important note : All end users must be registered with an Account prior to user licenses being assigned.| Committee |
D 02
|
| DocumentType |
Test Method
|
| Pages |
35
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1 This test method covers an engine test procedure for evaluating diesel engine oils for performance characteristics in a diesel engine equipped with exhaust gas recirculation, including viscosity increase and soot concentrations (loading).2 This test method is commonly referred to as the Mack T-11.
1.1.1This test method also provides the procedure for running an abbreviated length test, which is commonly referred to as the T-11A. The procedures for the T-11A are identical to the T-11 with the exception of the items specifically listed in Annex A8. Additionally, the procedure modifications listed in Annex A8 refer to the corresponding section of the T-11 procedure.
1.2The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.2.1Exceptions—Where there is no direct SI equivalent such as screw threads, National Pipe Threads/diameters, tubing size, or where there is a sole source supply equipment specification.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. See Annex A6 for specific safety hazards.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM D 4485 : 2018 : REV A | Standard Specification for Performance of Active API Service Category Engine Oils |
| ASTM D 4175 : 2014 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 5967 : 2015 | Standard Test Method for Evaluation of Diesel Engine Oils in T-8 Diesel Engine |
| ASTM D 4485 : 2003 : REV A | Standard Specification for Performance of Engine Oils |
| ASTM D 2622 : 1992 : EDT 1 | Standard Test Method for Sulfur in Petroleum Products by X-Ray Spectrometry |
| ASTM D 4175 : 2009 : REV A : EDT 1 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 7422 : 2012 | Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine |
| ASTM D 6896 : 2012 | Standard Test Method for Determination of Yield Stress and Apparent Viscosity of Used Engine Oils at Low Temperature |
| ASTM D 4175 : 2008 : REV B : EDT 1 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 5453 : 2009 | Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence |
| ASTM D 2274 : 2010 | Standard Test Method for Oxidation Stability of Distillate Fuel Oil (Accelerated Method) |
| ASTM D 4485 : 2006 | Standard Specification for Performance of Engine Oils |
| ASTM D 6278 : 1998 | Standard Test Method for Shear Stability of Polymer Containing Fluids Using a European Diesel Injector Apparatus |
| ASTM D 2622 : 1987 : EDT 1 | Standard Test Method for Sulfur in Petroleum Products by X-Ray Spectrometry |
| ASTM D 2709 : 1996 : R2011 : EDT 1 | Standard Test Method for Water and Sediment in Middle Distillate Fuels by Centrifuge |
| ASTM D 4175 : 2005 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 3524 : 2004 | Standard Test Method for Diesel Fuel Diluent in Used Diesel Engine Oils by Gas Chromatography (Withdrawn 2013) |
| ASTM D 2709 : 1996 : EDT 2 | Standard Test Method for Water and Sediment in Middle Distillate Fuels by Centrifuge |
| ASTM D 4485 : 2011 : REV C | Standard Specification for Performance of Active API Service Category Engine Oils |
| ASTM D 1319 : 1989 | Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Absorption |
| ASTM D 4175 : 2005 : EDT 2 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 1319 : 2008 | Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption |
| ASTM D 5967 : 2014 | Standard Test Method for Evaluation of Diesel Engine Oils in T-8 Diesel Engine |
| ASTM D 4485 : 2001 | Standard Specification for Performance of Engine Oils |
| ASTM D 5967 : 2008 | Standard Test Method for Evaluation of Diesel Engine Oils in T-8 Diesel Engine |
| ASTM D 5453 : 2008 : REV B | Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence |
| ASTM D 5453 : 2000 | Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Motor Fuels and Oils by Ultraviolet Fluorescence |
| ASTM D 7422 : 2009 | Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine |
| ASTM D 5185 : 1997 | Standard Test Method for Determination of Additive Elements, Wear Metals, and Contaminants in Used Lubricating Oils and Determination of Selected Elements in Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES) |
| ASTM D 4175 : 2015 : REV C | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 5967 : 2009 | Standard Test Method for Evaluation of Diesel Engine Oils in T-8 Diesel Engine |
| ASTM D 4175 : 2017 : REV A : EDT 1 | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 2274 : 2001 | Standard Test Method for Oxidation Stability of Distillate Fuel Oil (Accelerated Method) |
| ASTM D 4485 : 2003 | Standard Specification for Performance of Engine Oils |
| ASTM D 4052 : 1996 : R2002 : EDT 1 | Standard Test Method for Density and Relative Density of Liquids by Digital Density Meter |
| ASTM D 4485 : 2008 | Standard Specification for Performance of Engine Oils |
| ASTM D 4739 : 2005 | Standard Test Method for Base Number Determination by Potentiometric Titration |
| ASTM D 2709 : 1996 : R2006 | Standard Test Method for Water and Sediment in Middle Distillate Fuels by Centrifuge |
| ASTM D 4485 : 2015 | Standard Specification for Performance of Active API Service Category Engine Oils |
| ASTM D 5453 : 2004 | Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Motor Fuels and Oils by Ultraviolet Fluorescence |
| ASTM D 1319 : 2018 | Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption |
| ASTM D 4485 : 2005 : REV A | Standard Specification for Performance of Engine Oils |
| ASTM D 6896 : 2018 | Standard Test Method for Determination of Yield Stress and Apparent Viscosity of Used Engine Oils at Low Temperature |
| ASTM D 7422 : 2016 : REV A | Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine |
| ASTM D 6896 : 2003 | Standard Test Method for Determination of Yield Stress and Apparent Viscosity of Used Engine Oils at Low Temperature |
| ASTM D 4175 : 2008 : REV A | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 5453 : 2012 | Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence |
| ASTM D 4294 : 2010 | Standard Test Method for Sulfur in Petroleum and Petroleum Products by Energy Dispersive X-ray Fluorescence Spectrometry |
| ASTM D 2500 : 2016 : REV B | Standard Test Method for Cloud Point of Petroleum Products and Liquid Fuels |
| ASTM D 4052 : 2018 : REV A | Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter |
| ASTM D 5967 : 2012 | Standard Test Method for Evaluation of Diesel Engine Oils in T-8 Diesel Engine |
| ASTM D 1319 : 2014 | Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption |
| ASTM D 4175 : 2017 : REV B | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 4175 : 2009 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 4485 : 2011 : REV A | Standard Specification for Performance of Active API Service Category Engine Oils |
| ASTM D 5967 : 2003 | Standard Test Method for Evaluation of Diesel Engine Oils in T-8 Diesel Engine |
| ASTM D 2622 : 1998 | Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry |
| ASTM D 2500 : 2016 : REV A | Standard Test Method for Cloud Point of Petroleum Products and Liquid Fuels |
| ASTM D 2274 : 2003 : REV A : R2008 | Standard Test Method for Oxidation Stability of Distillate Fuel Oil (Accelerated Method) |
| ASTM D 2500 : 2016 | Standard Test Method for Cloud Point of Petroleum Products |
| ASTM D 1319 : 1999 | Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption |
| ASTM D 7422 : 2015 | Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine |
| ASTM D 4485 : 2018 | Standard Specification for Performance of Active API Service Category Engine Oils |
| ASTM D 5185 : 2005 | Standard Test Method for Determination of Additive Elements, Wear Metals, and Contaminants in Used Lubricating Oils and Determination of Selected Elements in Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES) |
| ASTM D 4737 : 2009 | Standard Test Method for Calculated Cetane Index by Four Variable Equation |
| ASTM D 4175 : 2009 : REV A : EDT 4 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 4175 : 2009 : REV A : EDT 3 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 4052 : 2009 | Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter |
| ASTM D 5453 : 2008 : REV A | Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence |
| ASTM D 5967 : 2004 | Standard Test Method for Evaluation of Diesel Engine Oils in T-8 Diesel Engine |
| ASTM D 5185 : 2002 | Standard Test Method for Determination of Additive Elements, Wear Metals, and Contaminants in Used Lubricating Oils and Determination of Selected Elements in Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES) |
| ASTM D 7109 : 2007 | Standard Test Method for Shear Stability of Polymer Containing Fluids Using a European Diesel Injector Apparatus at 30 and 90 Cycles |
| ASTM D 4485 : 2011 : REV B | Standard Specification for Performance of Active API Service Category Engine Oils |
| ASTM D 2622 : 2008 | Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry |
| ASTM D 4485 : 2016 | Standard Specification for Performance of Active API Service Category Engine Oils |
| ASTM D 4175 : 2018 | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 4485 : 2007 | Standard Specification for Performance of Engine Oils |
| ASTM D 7422 : 2014 : REV A | Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine |
| ASTM D 4485 : 2010 | Standard Specification for Performance of Engine Oils |
| ASTM D 5185 : 2018 | Standard Test Method for Multielement Determination of Used and Unused Lubricating Oils and Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES) |
| ASTM D 4485 : 2001 : REV A | Standard Specification for Performance of Engine Oils |
| ASTM D 7422 : 2010 : REV A | Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine |
| ASTM D 7422 : 2008 | Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine |
| ASTM D 4175 : 2001 : EDT 1 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 1319 : 2002 : REV A | Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption |
| ASTM D 2274 : 2003 | Standard Test Method for Oxidation Stability of Distillate Fuel Oil (Accelerated Method) |
| ASTM D 5453 : 2005 | Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Motor Fuels and Oils by Ultraviolet Fluorescence |
| ASTM D 7422 : 2017 : REV A | Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine |
| ASTM D 7109 : 2012 | Standard Test Method for Shear Stability of Polymer Containing Fluids Using a European Diesel Injector Apparatus at 30 and 90 Cycles |
| ASTM D 2709 : 2016 | Standard Test Method for Water and Sediment in Middle Distillate Fuels by Centrifuge |
| ASTM D 4175 : 2001 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 4175 : 2005 : EDT 1 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 2500 : 1999 | Standard Test Method for Cloud Point of Petroleum Products |
| ASTM D 2500 : 2002 : EDT 1 | Standard Test Method for Cloud Point of Petroleum Products |
| ASTM D 7109 : 2005 | Standard Test Method for Shear Stability of Polymer Containing Fluids Using a European Diesel Injector Apparatus at 30 and 90 Cycles |
| ASTM D 4739 : 2008 | Standard Test Method for Base Number Determination by Potentiometric Hydrochloric Acid Titration |
| ASTM D 2500 : 2005 | Standard Test Method for Cloud Point of Petroleum Products |
| ASTM D 4175 : 2002 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 5185 : 2013 : EDT 1 | Standard Test Method for Multielement Determination of Used and Unused Lubricating Oils and Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES) |
| ASTM D 4485 : 2004 | Standard Specification for Performance of Engine Oils |
| ASTM D 5453 : 2006 | Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence |
| ASTM D 6896 : 2003 : R2007 | Standard Test Method for Determination of Yield Stress and Apparent Viscosity of Used Engine Oils at Low Temperature |
| ASTM D 2500 : 2002 | Standard Test Method for Cloud Point of Petroleum Products |
| ASTM D 2500 : 2011 | Standard Test Method for Cloud Point of Petroleum Products |
| ASTM D 4739 : 2017 | Standard Test Method for Base Number Determination by Potentiometric Hydrochloric Acid Titration |
| ASTM D 5967 : 2015 : REV A | Standard Test Method for Evaluation of Diesel Engine Oils in T-8 Diesel Engine |
| ASTM D 2500 : 2009 | Standard Test Method for Cloud Point of Petroleum Products |
| ASTM D 3524 : 2014 | Standard Test Method for Diesel Fuel Diluent in Used Diesel Engine Oils by Gas Chromatography |
| ASTM D 4739 : 2006 | Standard Test Method for Base Number Determination by Potentiometric Titration |
| ASTM D 4294 : 2008 | Standard Test Method for Sulfur in Petroleum and Petroleum Products by Energy Dispersive X-ray Fluorescence Spectrometry |
| ASTM D 4175 : 2015 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 4485 : 2000 | Standard Specification for Performance of Engine Oils |
| ASTM D 6896 : 2014 | Standard Test Method for Determination of Yield Stress and Apparent Viscosity of Used Engine Oils at Low Temperature |
| ASTM D 4175 : 2002 : REV A : EDT 2 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 4739 : 1996 | Standard Test Method for Base Number Determination by Potentiometric Titration |
| ASTM D 2500 : 2017 | Standard Test Method for Cloud Point of Petroleum Products and Liquid Fuels |
| ASTM D 4052 : 2011 | Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter |
| ASTM D 1319 : 2003 | Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption |
| ASTM D 4052 : 2016 | Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter |
| ASTM D 7422 : 2013 | Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine |
| ASTM D 4485 : 2015 : REV A | Standard Specification for Performance of Active API Service Category Engine Oils |
| ASTM D 5185 : 2013 | Standard Test Method for Multielement Determination of Used and Unused Lubricating Oils and Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES) |
| ASTM D 2622 : 2003 | Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry |
| ASTM D 5453 : 2016 | Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence |
| ASTM D 4294 : 2008 : REV A | Standard Test Method for Sulfur in Petroleum and Petroleum Products by Energy Dispersive X-ray Fluorescence Spectrometry |
| ASTM D 1319 : 2010 | Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption |
| ASTM D 4175 : 2009 : REV A : EDT 5 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 4175 : 2016 : REV C | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 4737 : 2009 : REV A | Standard Test Method for Calculated Cetane Index by Four Variable Equation |
| ASTM D 5967 : 2011 | Standard Test Method for Evaluation of Diesel Engine Oils in T-8 Diesel Engine |
| ASTM D 4175 : 2015 : REV B | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 7422 : 2015 : REV A | Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine |
| ASTM D 6278 : 2017 | Standard Test Method for Shear Stability of Polymer Containing Fluids Using a European Diesel Injector Apparatus |
| ASTM D 4294 : 2002 | Standard Test Method for Sulfur in Petroleum Products by Energy-Dispersive X-Ray Fluorescence Spectroscopy |
| ASTM D 4175 : 2015 : REV A | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 5967 : 2017 | Standard Test Method for Evaluation of Diesel Engine Oils in T-8 Diesel Engine |
| ASTM D 4485 : 2006 : REV A | Standard Specification for Performance of Engine Oils |
| ASTM D 4739 : 2011 : R2017 | Standard Test Method for Base Number Determination by Potentiometric Hydrochloric Acid Titration |
| ASTM D 4737 : 2010 : R2016 | Standard Test Method for Calculated Cetane Index by Four Variable Equation |
| ASTM D 5453 : 2003 | Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Motor Fuels and Oils by Ultraviolet Fluorescence |
| ASTM D 2274 : 1994 : R1999 : EDT 1 | Standard Test Method for Oxidation Stability of Distillate Fuel Oil (Accelerated Method) |
| ASTM D 4175 : 2009 : REV A | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 7109 : 2004 | Standard Test Method for Shear Stability of Polymer Containing Fluids Using a European Diesel Injector Apparatus at 30 and 90 Cycles |
| ASTM D 4175 : 2016 : REV B | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 7422 : 2016 | Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine |
| ASTM D 2500 : 2017 : REV A | Standard Test Method for Cloud Point of Petroleum Products and Liquid Fuels |
| ASTM D 7422 : 2011 | Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine |
| ASTM D 4175 : 2002 : REV A : EDT 1 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 4175 : 2008 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 7422 : 2010 | Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine |
| ASTM D 6278 : 2017 : EDT 1 | Standard Test Method for Shear Stability of Polymer Containing Fluids Using a European Diesel Injector Apparatus |
| ASTM D 4737 : 2003 | Standard Test Method for Calculated Cetane Index by Four Variable Equation |
| ASTM D 4175 : 2002 : REV A | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 4294 : 2016 : EDT 1 | Standard Test Method for Sulfur in Petroleum and Petroleum Products by Energy Dispersive X-ray Fluorescence Spectrometry |
| ASTM D 5453 : 2016 : EDT 1 | Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence |
| ASTM D 6278 : 2012 : EDT 1 | Standard Test Method for Shear Stability of Polymer Containing Fluids Using a European Diesel Injector Apparatus |
| ASTM D 4175 : 2000 : EDT 1 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 3524 : 1990 : R1999 | Standard Test Method for Diesel Fuel Diluent in Used Diesel Engine Oils by Gas Chromatography |
| ASTM D 4175 : 2016 : REV A | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 5967 : 2007 | Standard Test Method for Evaluation of Diesel Engine Oils in T-8 Diesel Engine |
| ASTM D 7109 : 2018 | Standard Test Method for Shear Stability of Polymer-Containing Fluids Using a European Diesel Injector Apparatus at 30 Cycles and 90 Cycles |
| ASTM D 5967 : 2010 | Standard Test Method for Evaluation of Diesel Engine Oils in T-8 Diesel Engine |
| ASTM D 4294 : 2008 : REV A : EDT 1 | Standard Test Method for Sulfur in Petroleum and Petroleum Products by Energy Dispersive X-ray Fluorescence Spectrometry |
| ASTM D 4052 : 1996 | Standard Test Method for Density and Relative Density of Liquids by Digital Density Meter |
| ASTM D 4294 : 1998 | Standard Test Method for Sulfur in Petroleum Products by Energy-Dispersive X-Ray Fluorescence Spectroscopy |
| ASTM D 4739 : 2008 : EDT 1 | Standard Test Method for Base Number Determination by Potentiometric Hydrochloric Acid Titration |
| ASTM D 2622 : 2010 | Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry |
| ASTM D 2709 : 1988 | Standard Test Method for Water and Sediment in Distillate Fuels by Centrifuge |
| ASTM D 4485 : 2005 | Standard Specification for Performance of Engine Oils |
| ASTM D 5185 : 2009 | Standard Test Method for Determination of Additive Elements, Wear Metals, and Contaminants in Used Lubricating Oils and Determination of Selected Elements in Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES) |
| ASTM D 4737 : 1996 : REV A | Standard Test Method for Calculated Cetane Index by Four Variable Equation |
| ASTM D 7422 : 2009 : REV A | Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine |
| ASTM D 4485 : 2014 | Standard Specification for Performance of Active API Service Category Engine Oils |
| ASTM D 5453 : 2019 : REV A | Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence |
| ASTM D 5967 : 2013 | Standard Test Method for Evaluation of Diesel Engine Oils in T-8 Diesel Engine |
| ASTM D 4485 : 2002 | Standard Specification for Performance of Engine Oils |
| ASTM D 5967 : 2012 : REV A | Standard Test Method for Evaluation of Diesel Engine Oils in T-8 Diesel Engine |
| ASTM D 2622 : 2007 | Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry |
| ASTM D 6896 : 2003 : EDT 1 | Standard Test Method for Determination of Yield Stress and Apparent Viscosity of Used Engine Oils at Low Temperature |
| ASTM D 4175 : 2017 : REV A | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 2274 : 2003 : REV A | Standard Test Method for Oxidation Stability of Distillate Fuel Oil (Accelerated Method) |
| ASTM D 4485 : 2005 : EDT 1 | Standard Specification for Performance of Engine Oils |
| ASTM D 2622 : 1994 | Standard Test Method for Sulfur in Petroleum Products by X-Ray Spectrometry |
| ASTM D 5967 : 2005 | Standard Test Method for Evaluation of Diesel Engine Oils in T-8 Diesel Engine |
| ASTM D 4175 : 2009 : REV A : EDT 2 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 2622 : 2005 | Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry |
| ASTM D 5185 : 2002 : EDT 1 | Standard Test Method for Determination of Additive Elements, Wear Metals, and Contaminants in Used Lubricating Oils and Determination of Selected Elements in Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES) |
| ASTM D 4294 : 2003 | Standard Test Method for Sulfur in Petroleum and Petroleum Products by Energy-Dispersive X-Ray Fluorescence Spectrometry |
| ASTM D 4737 : 2004 | Standard Test Method for Calculated Cetane Index by Four Variable Equation |
| ASTM D 5453 : 2019 | Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence |
| ASTM D 4175 : 2018 : EDT 1 | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 4175 : 2016 | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 5967 : 2010 : REV A | Standard Test Method for Evaluation of Diesel Engine Oils in T-8 Diesel Engine |
| ASTM D 1319 : 2015 | Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption |
| ASTM D 7422 : 2017 | Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine |
| ASTM D 4294 : 2016 | Standard Test Method for Sulfur in Petroleum and Petroleum Products by Energy Dispersive X-ray Fluorescence Spectrometry |
| ASTM D 5185 : 2002 : EDT 2 | Standard Test Method for Determination of Additive Elements, Wear Metals, and Contaminants in Used Lubricating Oils and Determination of Selected Elements in Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES) |
| ASTM D 4739 : 2011 | Standard Test Method for Base Number Determination by Potentiometric Hydrochloric Acid Titration |
| ASTM D 4739 : 2002 | Standard Test Method for Base Number Determination by Potentiometric Titration |
| ASTM D 1319 : 2013 | Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption |
| ASTM D 4052 : 2015 | Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter |
| ASTM D 4739 : 2006 : REV A | Standard Test Method for Base Number Determination by Potentiometric Titration |
| ASTM D 6278 : 2002 | Standard Test Method for Shear Stability of Polymer Containing Fluids Using a European Diesel Injector Apparatus |
| ASTM D 5967 : 1999 : REV A | Standard Test Method for Evaluation of Diesel Engine Oils in T-8 Diesel Engine |
| ASTM D 4175 : 2017 | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 6278 : 2007 | Standard Test Method for Shear Stability of Polymer Containing Fluids Using a European Diesel Injector Apparatus |
| ASTM D 4175 : 2019 | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 2274 : 2001 : REV A | Standard Test Method for Oxidation Stability of Distillate Fuel Oil (Accelerated Method) |
| ASTM D 4485 : 2009 | Standard Specification for Performance of Engine Oils |
| ASTM D 2274 : 2014 | Standard Test Method for Oxidation Stability of Distillate Fuel Oil (Accelerated Method) |
| ASTM D 4175 : 2015 : REV B : EDT 1 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 6896 : 2017 | Standard Test Method for Determination of Yield Stress and Apparent Viscosity of Used Engine Oils at Low Temperature |
| ASTM D 4485 : 2010 : REV A | Standard Specification for Performance of Engine Oils |
| ASTM D 5453 : 2003 : REV A | Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Motor Fuels and Oils by Ultraviolet Fluorescence |
| ASTM D 4485 : 2011 | Standard Specification for Performance of Engine Oils |
| ASTM D 1319 : 2019 | Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption |
| ASTM D 7109 : 2006 | Standard Test Method for Shear Stability of Polymer Containing Fluids Using a European Diesel Injector Apparatus at 30 and 90 Cycles |
| ASTM D 4052 : 2018 | Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter |
| ASTM D 4737 : 2010 | Standard Test Method for Calculated Cetane Index by Four Variable Equation |
| ASTM D 4294 : 1990 : R1998 : EDT 1 | Standard Test Method for Sulfur in Petroleum Products by Energy-Dispersive X-Ray Fluorescence Spectroscopy |
| ASTM D 1319 : 2002 | Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption |
| ASTM D 4175 : 2008 : REV B | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 2622 : 2016 | Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry |
| ASTM D 2709 : 1996 : R2001 : EDT 1 | Standard Test Method for Water and Sediment in Middle Distillate Fuels by Centrifuge |
| ASTM D 7422 : 2014 | Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine |
| ASTM D 5453 : 2008 | Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence |
| ASTM D 4485 : 2007 : REV A | Standard Specification for Performance of Engine Oils |
| ASTM D 5453 : 2000 : EDT 1 | Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Motor Fuels and Oils by Ultraviolet Fluorescence |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.