ASTM D 7150 : 2013 : REDLINE
Current
The latest, up-to-date edition.
Standard Test Method for the Determination of Gassing Characteristics of Insulating Liquids Under Thermal Stress
English
12-01-2013
CONTAINED IN VOL. 10.03, 2015 Defines the procedures to determine the low temperature (120 degrees C) gassing characteristics of insulating liquids specifically and without the influence of other electrical apparatus materials or electrical stresses.
Committee |
D 27
|
DocumentType |
Redline
|
Pages |
6
|
PublisherName |
American Society for Testing and Materials
|
Status |
Current
|
1.1This test method describes the procedures to determine the gassing characteristics due to thermal stress at 120°C of insulating liquids specifically and without the influence of other electrical apparatus materials or electrical stresses. This test method was primarily designed for insulating mineral oil. It can be applied to other insulating liquids in which dissolved gas-in-oil analysis (Test Method D3612) is commonly performed.
1.2This test method is particularly suited for detection of the phenomenon sometimes known as “stray gassing” and is also referred to in CIGRE TF11 B39.
1.3This test method is performed on transformer insulating liquids to determine the propensity of the oil to produce certain gases such as hydrogen and hydrocarbons at low temperatures.
1.4This test method details two procedures:
1.5Method A describes the procedure for determining the gassing characteristics of insulating liquids, at 120°C for 164 h.
1.6Method B describes the procedure for processing the insulating liquid through an attapulgite clay column to remove organic contaminants and other reactive groups that may influence the gassing behavior of an insulating liquid, which is suspected of being contaminated. This procedure applies to both new and used insulating liquids.
1.7The values stated in SI units are to be regarded as standard. English units are used when there is no metric equivalent.
1.8This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to use.
I.S. EN 62701:2014 | FLUIDS FOR ELECTROTECHNICAL APPLICATIONS - RECYCLED MINERAL INSULATING OILS FOR TRANSFORMERS AND SWITCHGEARS |
I.S. EN 60296:2012 | FLUIDS FOR ELECTROTECHNICAL APPLICATIONS - UNUSED MINERAL INSULATING OILS FOR TRANSFORMERS AND SWITCHGEAR (IEC 60296:2012 (EQV)) |
IEC 60599:2015 | Mineral oil-filled electrical equipment in service - Guidance on the interpretation of dissolved and free gases analysis |
EN 62701:2014 | Fluids for electrotechnical applications - Recycled mineral insulating oils for transformers and switchgears |
IEC 60599:2015 RLV | Mineral oil-filled electrical equipment in service - Guidance on the interpretation of dissolved and free gases analysis |
BS EN 60296:2012 | Fluids for electrotechnical applications. Unused mineral insulating oils for transformers and switchgear |
BS EN 60599:2016 | Mineral oil-filled electrical equipment in service. Guidance on the interpretation of dissolved and free gases analysis |
CEI EN 60296 : 2013 | FLUIDS FOR ELECTROTECHNICAL APPLICATIONS - UNUSED MINERAL INSULATING OILS FOR TRANSFORMERS AND SWITCHGEAR |
EN 60296:2012 | Fluids for electrotechnical applications - Unused mineral insulating oils for transformers and switchgear |
11/30235371 DC : 0 | BS EN 62701 - FLUIDS FOR ELECTRO TECHNICAL APPLICATIONS - RECYCLED MINERAL INSULATING OILS FOR TRANSFORMERS AND SWITCHGEARS |
I.S. EN 60599:2016 | MINERAL OIL-FILLED ELECTRICAL EQUIPMENT IN SERVICE - GUIDANCE ON THE INTERPRETATION OF DISSOLVED AND FREE GASES ANALYSIS |
UNE-EN 60296:2012 | Fluids for electrotechnical applications - Unused mineral insulating oils for transformers and switchgear |
IEEE C57.155-2014 | IEEE Guide for Interpretation of Gases Generated in Natural Ester and Synthetic Ester-Immersed Transformers |
UNE-EN 60599:2016 | Mineral oil-filled electrical equipment in service - Guidance on the interpretation of dissolved and free gases analysis |
IEC 60296:2012 RLV | Fluids for electrotechnical applications - Unused mineral insulating oils for transformers and switchgear |
EN 60599:2016 | Mineral oil-filled electrical equipment in service - Guidance on the interpretation of dissolved and free gases analysis |
IEC 60599:2015 | Mineral oil-filled electrical equipment in service - Guidance on the interpretation of dissolved and free gases analysis |
IEEE C57.104-2008 | IEEE Guide for the Interpretation of Gases Generated in Oil-Immersed Transformers |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.