• Shopping Cart
    There are no items in your cart

ASTM D 7094 : 2023

Current

Current

The latest, up-to-date edition.

Standard Test Method for Flash Point by Modified Continuously Closed Cup (MCCCFP) Tester

Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

01-09-2024

US$63.00
Excluding Tax where applicable

Committee
D 02
DocumentType
Test Method
Pages
10
PublisherName
American Society for Testing and Materials
Status
Current
Supersedes

1.1This test method covers the determination of the flash point of fuels including diesel/biodiesel blends, lube oils, solvents, and other liquids by a continuously closed cup tester utilizing a specimen size of 2 mL, cup size of 7 mL, with a heating rate of 2.5 °C per minute.

1.1.1Apparatus requiring a specimen size of 1 mL, cup size of 4 mL, and a heating rate of 5.5 °C per minute must be run according to Test Method D6450.

1.2This flash point test method is a dynamic method and depends on definite rates of temperature increase. It is one of the many flash point test methods available and every flash point test method, including this one, is an empirical method.

Note 1:Flash point values are not a constant physical chemical property of materials tested. They are a function of the apparatus design, the condition of the apparatus used, and the operational procedure carried out. Flash point can, therefore, only be defined in terms of a standard test method and no general valid correlation can be guaranteed between results obtained by different test methods or where different test apparatus is specified.

1.3This test method utilizes a closed but unsealed cup with air injected into the test chamber.

1.4The precision of this test method is applicable for testing samples with a flash point from 22.5 °C to 235.5 °C. Determinations below and above this range may be performed; however, the precision has not been established.

1.5If the user’s specification requires a defined flash point method other than this method, neither this method nor any other test method should be substituted for the prescribed test method without obtaining comparative data and an agreement from the specifier.

1.6The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. Temperatures are in degrees Celsius, pressure in kilo-Pascals.

1.7This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific warning statements, see 7.2 and 8.5.

1.8This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ASTM D 2880 : 2023 Standard Specification for Gas Turbine Fuel Oils
ASTM D 975 : 2023 : REV A Standard Specification for Diesel Fuel
ASTM D 6448 : 2016 : R2022 Standard Specification for Industrial Burner Fuels from Used Lubricating Oils
ASTM D 4378 : 2022 Standard Practice for In-Service Monitoring of Mineral Turbine Oils for Steam, Gas, and Combined Cycle Turbines
ASTM D 3699 : 2019 Standard Specification for Kerosine
ASTM F 3337 : 2023 Standard Guide for Taking Property and Behavior Measurements on Weathered Fractions of Oil
ASTM D 7467 : 2023 Standard Specification for Diesel Fuel Oil, Biodiesel Blend (B6 to B20)
ASTM D 396 : 2021 Standard Specification for Fuel Oils
ASTM D 4485 : 2022 : EDT 1 Standard Specification for Performance of Active API Service Category Engine Oils
ASTM D 6074 : 2015 : R2022 Standard Guide for Characterizing Hydrocarbon Lubricant Base Oils

ASTM D 6708 : 2024 Standard Practice for Statistical Assessment and Improvement of Expected Agreement Between Two Test Methods that Purport to Measure the Same Property of a Material
ASTM D 6300 : 2023 : REV A Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 6708 : 2021 Standard Practice for Statistical Assessment and Improvement of Expected Agreement Between Two Test Methods that Purport to Measure the Same Property of a Material
ASTM D 4175 : 2023 : REV A Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 4175 : 2024 Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 6300 : 2024 Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products, Liquid Fuels, and Lubricants

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.