ASTM D 709 : 2017 : REDLINE
Current
The latest, up-to-date edition.
Standard Specification for Laminated Thermosetting Materials
English
04-18-2017
Important note : All end users must be registered with an Account prior to user licenses being assigned.CONTAINED IN VOL. 10.01, 2017 Defines laminated thermosetting materials consisting of two or more plies or layers of reinforcing material bonded by a thermosetting synthetic resin.
| Committee |
D 09
|
| DevelopmentNote |
Supersedes L P 513 (C) (07/2000) Supersedes ASTM D 1592, ASTM D 616, ASTM D 467 and ASTM D 1532. (02/2002) Supersedes L P 387 (A), L P 513 (C) and L P 509 (A). (05/2004)
|
| DocumentType |
Redline
|
| Pages |
35
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Current
|
| Supersedes |
1.1This specification covers laminated thermosetting materials consisting of two or more plies or layers of reinforcing material bonded by a thermosetting synthetic resin. Examples of such reinforcement are cellulose paper, cotton fabric, glass fabric, and synthetic fiber fabrics. These materials are available in the form of sheets, rolled and molded tubes, and molded rods.
1.2The values stated in inch-pound units are to be regarded as the standard.
Note 1:This specification resembles IEC 60893-3 in title only. The content is significantly different.
1.3The following safety hazards caveat pertains only to the test methods described in this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM F 992 : 2017 : REDLINE | Standard Specification for Valve Label Plates |
| IPC AJ 820 : A | ASSEMBLY AND JOINING HANDBOOK |
| MIL-DTL-24151 Revision B:2016 | DOORS, ROLLER CURTAIN AND HINGED SLAT, AND ASSOCIATED OPERATING EQUIPMENT |
| MIL-DTL-28778 Revision A:2005 | TRANSFORMER, POWER, STEPUP, 3 PHASE |
| MIL B 18 : F | BATTERIES, NON-RECHARGEABLE, DRY |
| MIL-DTL-32360 Base Document:2010 | STOP LIGHT - TAILLIGHT, VEHICULAR-24 VOLT, SERVICE STOP, SERVICE TAIL, BLACKOUT TAIL |
| MIL-DTL-16036 Revision M:2013 | SWITCHGEAR, POWER, LOW VOLTAGE, NAVAL SHIPBOARD |
| MIL-DTL-12606 Revision E:2000 | LOUDSPEAKER, PERMANENT MAGNET (UNENCASED, 3-INCH AND 4-INCH DIAMETER CONE, 2-WATT; FUNGUS-, AND IMMERSION-RESISTANT), TYPE LS-445/U, M12606-01, AND M12606-02 |
| MIL-DTL-10911 Revision E:2012 | LOUDSPEAKERS, PERMANENT MAGNET, (UNENCASED, 2.5-, 3-, 4-, 5-, 6-, 8-, 10-, AND 12-INCH DIAMETER CONES), GENERAL SPECIFICATION FOR |
| MIL S 4880 : G NOTICE 1 | SWEEPER, MAGNET, SELF-PROPELLED |
| MIL-DTL-15024 Revision F:1997 | Plates and Tags for Identification of Equipment, General Specification for |
| MIL-DTL-16034 Revision B:2008 | METERS, ELECTRICAL-INDICATING (SWITCHBOARD AND PORTABLE TYPES), GENERAL SPECIFICATION FOR |
| CSA C22.2 No. 0.2 : 2016 | INSULATION COORDINATION |
| ASTM D 6054 : 1997 | Standard Practice for Conditioning Electrical Insulating Materials for Testing |
| MIL-STD-13231 Base Document:1999 | MARKING OF ELECTRONIC ITEMS |
| MIL-DTL-12883 Revision F:2003 | Sockets and Accessories for Plug-in Electronic Components, General Specification for |
| MIL-B-49030 Revision A:2010 | BATTERIES, DRY (ALKALINE) |
| CSA C22.2 No. 263 : 2015 | FIRE PUMP CONTROLLERS |
| ASTM D 2132 : 2012-02 | TEST METHOD FOR DUST-AND-FOG TRACKING AND EROSION RESISTANCE OF ELECTRICAL INSULATING MATERIALS |
| ASTM D 1867 : 2013 : REDLINE | Standard Specification for Copper-Clad Thermosetting Laminates for Printed Wiring |
| ASTM E 1420 : 1991 | Practice for Specifying Polymeric Materials for Service in Ionizing Radiation Environments (Withdrawn 1996) |
| ASTM D 618 : 2013 : REDLINE | Standard Practice for Conditioning Plastics for Testing |
| ASTM D 6054 : 1997 : R2004 | Standard Practice for Conditioning Electrical Insulating Materials for Testing (Withdrawn 2012) |
| ASTM D 495 : 2014 | Standard Test Method for High-Voltage, Low-Current, Dry Arc Resistance of Solid Electrical Insulation |
| IEEE 99-2007 REDLINE | IEEE Recommended Practice for the Preparation of Test Procedures for the Thermal Evaluation of Insulation Systems for Electrical Equipment |
| ASTM D 668 : 2012 : REDLINE | Standard Test Methods of Measuring Dimensions of Rigid Rods and Tubes Used for Electrical Insulation |
| ASTM D 349 : 2013 : REDLINE | Standard Test Methods for Laminated Round Rods Used for Electrical Insulation |
| ASTM D 1711 : 2015 : REDLINE | Standard Terminology Relating to Electrical Insulation |
| ASTM D 2303 : 2013 | Standard Test Methods for Liquid-Contaminant, Inclined-Plane Tracking and Erosion of Insulating Materials |
| IEEE 101 : 1987 | GUIDE FOR THE STATISTICAL ANALYSIS OF THERMAL LIFE TEST DATA |
| IEEE 98-2002 | IEEE Standard for the Preparation of Test Procedures for the Thermal Evaluation of Solid Electrical Insulating Materials |
| ASTM D 348 : 2013 : REDLINE | Standard Test Methods for Rigid Tubes Used for Electrical Insulation |
| ASTM D 257 : 2014 : REDLINE | Standard Test Methods for DC Resistance or Conductance of Insulating Materials |
| ASTM D 2304 : 2010-10 | TEST METHOD FOR THERMAL ENDURANCE OF RIGID ELECTRICAL INSULATING MATERIALS |
| NEMA LI 1 : 1998(R2011) | INDUSTRIAL LAMINATED THERMOSETTING PRODUCTS |
| MIL-I-24768 Base Document:1992 | INSULATION, PLASTICS, LAMINATED, THERMOSETTING, GENERAL SPECIFICATION FOR |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.