ASTM D 7060 : 2012 : R2014
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Determination of the Maximum Flocculation Ratio and Peptizing Power in Residual and Heavy Fuel Oils (Optical Detection Method)
Hardcopy , PDF
12-16-2019
English
12-01-2014
Important note : All end users must be registered with an Account prior to user licenses being assigned.CONTAINED IN VOL. 05.04, 2018 Defines a procedure for quantifying the maximum flocculation ratio of the asphaltenes in the oil and the peptizing power of the oil medium, by an automatic instrument using an optical device.
| Committee |
D 02
|
| DocumentType |
Test Method
|
| Pages |
12
|
| ProductNote |
Reconfirmed 2014
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This test method covers a procedure for quantifying the maximum flocculation ratio of the asphaltenes in the oil and the peptizing power of the oil medium, by an automatic instrument using an optical device.
1.2This test method is applicable to atmospheric or vacuum distillation residues, thermally cracked residue, intermediate and finished residual fuel oils, containing at least 1 mass % asphaltenes. This test method has not been developed for asphalts.
Note 1:An optical probe detects the formation of flocculated asphaltenes. The start of flocculation is interpreted when a significant and sustained increase in rate-of-change of signal, as measured by the optical probe, ensures flocculation is in progress. The start of flocculation can be detected unambiguously when the sample contains at least 1 % mass asphaltenes as measured by Test Method D6560.
Note 2:This test method is applicable to products typical of Specification D396—Grades 5L, 5H, and 6, and Specification D2880—Grades 3-GT and 4-GT.
1.3This test method was evaluated in an interlaboratory study in the nominal range of 32 to 76 for the maximum flocculation ratio and in the nominal range of 36 to 95 for peptizing power.
Note 3:The nominal range is determined by (min. sample mean—Reproducibility) to (max. sample mean + Reproducibility).
1.4The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| ASTM D 4057 : 2019 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
| ASTM D 6300 : 2013 | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
| ASTM D 6300 : 2014 : REV A : EDT 1 | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
| ASTM D 4177 : 2016 : EDT 1 | Standard Practice for Automatic Sampling of Petroleum and Petroleum Products |
| ASTM D 6300 : 2017 | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
| ASTM D 4177 : 1995 | Standard Practice for Automatic Sampling of Petroleum and Petroleum Products |
| ASTM D 6300 : 2017 : REV A | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
| ASTM D 4057 : 2012 : R2018 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
| ASTM D 6792 : 2006 | Standard Guide for Quality System in Petroleum Products and Lubricants Testing Laboratories |
| ASTM D 4870 : 2018 | Standard Test Method for Determination of Total Sediment in Residual Fuels |
| ASTM D 6792 : 2017 : REDLINE | Standard Practice for Quality Management Systems in Petroleum Products, Liquid Fuels, and Lubricants Testing Laboratories |
| ASTM D 2880 : 2000 | Standard Specification for Gas Turbine Fuel Oils |
| ASTM D 6792 : 2004 | Standard Guide for Quality System in Petroleum Products and Lubricants Testing Laboratories |
| ASTM D 6300 : 2016 | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
| ASTM D 4057 : 1981 : EDT 2 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
| ASTM D 6300 : 2004 | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
| ASTM D 2880 : 1990 | Standard Specification for Gas Turbine Fuel Oils |
| ASTM D 6300 : 2019 | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
| ASTM D 2880 : 2013 | Standard Specification for Gas Turbine Fuel Oils |
| ASTM D 6792 : 2004 : REV A | Standard Guide for Quality System in Petroleum Products and Lubricants Testing Laboratories |
| ASTM D 2880 : 2013 : REV A | Standard Specification for Gas Turbine Fuel Oils |
| ASTM D 6792 : 2005 | Standard Guide for Quality System in Petroleum Products and Lubricants Testing Laboratories |
| ASTM D 2880 : 2018 | Standard Specification for Gas Turbine Fuel Oils |
| ASTM D 4057 : 2006 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
| ASTM D 2880 : 1998 | Standard Specification for Gas Turbine Fuel Oils |
| ASTM D 4177 : 2015 | Standard Practice for Automatic Sampling of Petroleum and Petroleum Products |
| ASTM D 4870 : 2009 | Standard Test Method for Determination of Total Sediment in Residual Fuels |
| ASTM D 4057 : 2012 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
| ASTM D 6300 : 2006 | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
| ASTM D 6792 : 2013 | Standard Practice for Quality System in Petroleum Products and Lubricants Testing Laboratories |
| ASTM D 2880 : 2003 : R2010 | Standard Specification for Gas Turbine Fuel Oils |
| ASTM D 4870 : 2007 : REV A | Standard Test Method for Determination of Total Sediment in Residual Fuels |
| ASTM D 6792 : 2017 | Standard Practice for Quality Management Systems in Petroleum Products, Liquid Fuels, and Lubricants Testing Laboratories |
| ASTM D 6300 : 2014 : REV A | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
| ASTM D 6300 : 2015 | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
| ASTM D 6300 : 1999 | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
| ASTM D 6792 : 2007 | Standard Practice for Quality System in Petroleum Products and Lubricants Testing Laboratories |
| ASTM D 4870 : 2009 : R2014 | Standard Test Method for Determination of Total Sediment in Residual Fuels |
| ASTM D 4177 : 1995 : R2010 | Standard Practice for Automatic Sampling of Petroleum and Petroleum Products |
| ASTM D 6560 : 2000 : R2005 | Standard Test Method for Determination of Asphaltenes (Heptane Insolubles) in Crude Petroleum and Petroleum Products |
| ASTM D 2880 : 2015 | Standard Specification for Gas Turbine Fuel Oils |
| ASTM D 4177 : 1995 : R2000 | Standard Practice for Automatic Sampling of Peroleum and Petroleum Products |
| ASTM D 4870 : 2004 | Standard Test Method for Determination of Total Sediment in Residual Fuels |
| ASTM D 6300 : 2013 : REV A | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
| ASTM D 6300 : 2008 | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
| ASTM D 6300 : 2003 | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
| ASTM D 4870 : 1999 | Standard Test Method for Determination of Total Sediment in Residual Fuels |
| ASTM D 6300 : 2007 | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
| ASTM D 2880 : 2014 | Standard Specification for Gas Turbine Fuel Oils |
| ASTM D 6300 : 2002 | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
| ASTM D 6560 : 2012 | Standard Test Method for Determination of Asphaltenes (Heptane Insolubles) in Crude Petroleum and Petroleum Products |
| ASTM D 2880 : 2013 : REV B | Standard Specification for Gas Turbine Fuel Oils |
| ASTM D 6560 : 2000 | Standard Test Method for Determination of Asphaltenes (Heptane Insolubles) in Crude Petroleum and Petroleum Products |
| ASTM D 4177 : 2016 | Standard Practice for Automatic Sampling of Petroleum and Petroleum Products |
| ASTM D 6792 : 2003 | Standard Guide for Quality System in Petroleum Products and Lubricants Testing Laboratories |
| ASTM D 4177 : 1995 : R2005 | Standard Practice for Automatic Sampling of Petroleum and Petroleum Products |
| ASTM D 2880 : 1996 | Standard Specification for Gas Turbine Fuel Oils |
| ASTM D 6300 : 2016 : REV A | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
| ASTM D 6792 : 2002 | Standard Guide for A Quality System in Petroleum Products and Lubricants Testing Laboratories |
| ASTM D 6560 : 2017 | Standard Test Method for Determination of Asphaltenes (Heptane Insolubles) in Crude Petroleum and Petroleum Products |
| ASTM D 4057 : 1995 : R2000 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
| ASTM D 4177 : 2015 : REV A | Standard Practice for Automatic Sampling of Petroleum and Petroleum Products |
| ASTM D 6300 : 2014 | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
| ASTM D 4057 : 2006 : R2011 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
| ASTM D 2880 : 1978 | Standard Specification for Gas Turbine Fuel Oils |
| ASTM D 4870 : 2007 | Standard Test Method for Determination of Total Sediment in Residual Fuels |
| ASTM D 2880 : 2003 | Standard Specification for Gas Turbine Fuel Oils |
| ASTM D 2880 : 2014 : REV A | Standard Specification for Gas Turbine Fuel Oils |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.