ASTM D 6577 : 2015 : R2019
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Guide for Testing Industrial Protective Coatings
Available format(s)
Hardcopy , PDF
Superseded date
07-31-2024
Superseded by
Language(s)
English
Published date
10-01-2019
Important note : All end users must be registered with an Account prior to user licenses being assigned.| Committee |
D 01
|
| DocumentType |
Guide
|
| Pages |
12
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This guide covers the selection and use of test methods and procedures for testing industrial protective coatings. Selection of the standards to be followed must be governed by experience and the requirements in each individual case, together with agreement between the supplier and the user.
1.2This guide covers the testing of liquid coatings as applied on substrate by brushing, rolling, spraying, or other means appropriate to the coating and circumstance.
Note 1:The term “industrial protective coating” as used in this guide is described in the scope of Subcommittee D01.461 as “paints applied to substrates on-site of structures and buildings, especially where subject to corrosive environments, as industrial, urban, and marine environments.”
Note 2:Guides for testing other coating types, such as Guides D4712, D5146, D5324 or for surface preparation, coating application, such as Guide D3276, are available and should be used when it is applicable.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM D 6943 : 2015 : R2024 | Standard Practice for Immersion Testing of Industrial Protective Coatings and Linings |
| ASTM D 2200 : 2017 : R2021 | Standard Practice for Use of Pictorial Surface Preparation Standards and Guides for Painting Steel Surfaces |
| ASTM D 1212 : 1991 : R2013 | Standard Test Methods for Measurement of Wet Film Thickness of Organic Coatings |
| ASTM D 1005 : 1995 : R2020 | Standard Test Method for Measurement of Dry-Film Thickness of Organic Coatings Using Micrometers |
| ASTM D 5895 : 2013 | Standard Test Methods for Evaluating Drying or Curing During Film Formation of Organic Coatings Using Mechanical Recorders |
| ASTM D 1730 : 2009 : R2014 | Standard Practices for Preparation of Aluminum and Aluminum-Alloy Surfaces for Painting |
| ASTM D 3276 : 2015 : EDT 1 | Standard Guide for Painting Inspectors (Metal Substrates) |
| ASTM D 3278 : 2020 | Standard Test Methods for Flash Point of Liquids by Small Scale Closed-Cup Apparatus |
| ASTM G 14 : 2004 : R2024 | Standard Test Method for Impact Resistance of Pipeline Coatings (Falling Weight Test) |
| ASTM D 3363 : 2022 | Standard Test Method for Film Hardness by Pencil Test |
| ASTM G 90 : 2017 | Standard Practice for Performing Accelerated Outdoor Weathering of Materials Using Concentrated Natural Sunlight |
| ASTM D 185 : 2007 : R2019 | Standard Test Methods for Coarse Particles in Pigments |
| ASTM E 84 : 2023 : REV D | Standard Test Method for Surface Burning Characteristics of Building Materials |
| ASTM D 7187 : 2020 | Standard Test Method for Measuring Mechanistic Aspects of Scratch/Mar Behavior of Paint Coatings by Nanoscratching |
| ASTM D 4138 : 2007 : REV A : R2022 | Standard Practices for Measurement of Dry Film Thickness of Protective Coating Systems by Destructive, Cross-Sectioning Means |
| ASTM D 2697 : 2022 | Standard Test Method for Volume Nonvolatile Matter in Clear or Pigmented Coatings |
| ASTM D 3276 : 2021 | Standard Guide for Painting Inspectors (Metal Substrates) |
| ASTM D 2244 : 2021 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
| ASTM G 14 : 2004 : R2018 | Standard Test Method for Impact Resistance of Pipeline Coatings (Falling Weight Test) |
| ASTM D 3363 : 2005 : R2011 : EDT 2 | Standard Test Method for Film Hardness by Pencil Test (Withdrawn 2020) |
| ASTM D 5178 : 2021 | Standard Test Method for Mar Resistance of Organic Coatings |
| ASTM D 772 : 2018 | Standard Test Method for Evaluating Degree of Flaking (Scaling) of Exterior Paints |
| ASTM D 2201 : 2018 | Standard Practice for Preparation of Zinc-Coated and Zinc-Alloy-Coated Steel Panels for Testing Paint and Related Coating Products |
| ASTM G 141 : 2009 : R2021 | Standard Guide for Addressing Variability in Exposure Testing of Nonmetallic Materials |
| ASTM D 6093 : 1997 : R2022 | Standard Test Method for Percent Volume Nonvolatile Matter in Clear or Pigmented Coatings Using a Helium Gas Pycnometer |
| ASTM D 5064 : 2016 : REV A | Standard Practice for Conducting a Patch Test to Assess Coating Compatibility |
| ASTM D 5327 : 1997 : R2013 | Standard Practice for Evaluating and Comparing Transfer Efficiency of Spray Applied Coatings Under General Laboratory Conditions |
| ASTM G 141 : 2009 : R2013 | Standard Guide for Addressing Variability in Exposure Testing of Nonmetallic Materials |
| ASTM E 84 : 2023 : REV C | Standard Test Method for Surface Burning Characteristics of Building Materials |
| ASTM C 868 : 1985 : R1995 : EDT 1 | Standard Test Method for Chemical Resistance of Protective Linings |
| ASTM D 4958 : 2024 | Standard Test Method for Comparison of the Brush Drag of Latex Paints |
| ASTM D 4062 : 2024 | Standard Test Method for Leveling of Paints by Draw-Down Method |
| ASTM D 1735 : 2021 | Standard Practice for Testing Water Resistance of Coatings Using Water Fog Apparatus |
| ASTM D 2616 : 2019 | Standard Test Method for Evaluation of Visual Color Difference With a Gray Scale |
| ASTM D 4587 : 1991 | Standard Practice for Fluorescent UV-Condensation Exposures of Paint and Related Coatings |
| ASTM G 90 : 2023 | Standard Practice for Performing Accelerated Outdoor Weathering of Materials Using Concentrated Natural Sunlight |
| ASTM D 2244 : 2023 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
| ASTM D 6093 : 1997 : R2016 | Standard Test Method for Percent Volume Nonvolatile Matter in Clear or Pigmented Coatings Using a Helium Gas Pycnometer |
| ASTM G 154 : 2016 | Standard Practice for Operating Fluorescent Ultraviolet (UV) Lamp Apparatus for Exposure of Nonmetallic Materials |
| ASTM D 772 : 2024 | Standard Test Method for Evaluating Degree of Flaking (Scaling) of Exterior Paints |
| ASTM D 869 : 2021 | Standard Test Method for Evaluating Degree of Settling of Paint |
| ASTM D 7055 : 2019 : R2024 | Standard Practice for Preparation (by Abrasive Blast Cleaning) of Hot-Rolled Carbon Steel Panels for Testing of Coatings |
| ASTM G 85 : 2019 | Standard Practice for Modified Salt Spray (Fog) Testing |
| ASTM G 153 : 2013 | Standard Practice for Operating Enclosed Carbon Arc Light Apparatus for Exposure of Nonmetallic Materials |
| ASTM D 609 : 2017 : R2022 | Standard Practice for Preparation of Cold-Rolled Steel Panels for Testing Paint, Varnish, Conversion Coatings, and Related Coating Products |
| ASTM D 5162 : 2021 | Standard Practice for Discontinuity (Holiday) Testing of Nonconductive Protective Coating on Metallic Substrates |
| ASTM D 4017 : 2002 : R2015 | Standard Test Method for Water in Paints and Paint Materials by Karl Fischer Method |
| ASTM D 1735 : 1999 | Standard Practice for Testing Water Resistance of Coatings Using Water Fog Apparatus |
| ASTM D 2794 : 1993 : R2024 | Standard Test Method for Resistance of Organic Coatings to the Effects of Rapid Deformation (Impact) |
| ASTM D 6093 : 1997 | Standard Test Method for Percent Volume Nonvolatile Matter in Clear or Pigmented Coatings Using a Helium Gas Pycnometer |
| ASTM D 3168 : 1985 : R2022 | Standard Practice for Qualitative Identification of Polymers in Emulsion Paints |
| ASTM D 1729 : 2016 | Standard Practice for Visual Appraisal of Colors and Color Differences of Diffusely-Illuminated Opaque Materials |
| ASTM D 869 : 1985 : R2015 | Standard Test Method for Evaluating Degree of Settling of Paint |
| ASTM D 1200 : 2023 | Standard Test Method for Viscosity by Ford Viscosity Cup |
| ASTM D 2805 : 2011 : R2018 | Standard Test Method for Hiding Power of Paints by Reflectometry |
| ASTM D 1200 : 2010 : R2018 | Standard Test Method for Viscosity by Ford Viscosity Cup |
| ASTM D 4062 : 2011 : R2016 | Standard Test Method for Leveling of Paints by Draw-Down Method |
| ASTM D 7091 : 2022 | Standard Practice for Nondestructive Measurement of Dry Film Thickness of Nonmagnetic Coatings Applied to Ferrous Metals and Nonmagnetic, Nonconductive Coatings Applied to Non-Ferrous Metals |
| ASTM G 95 : 2007 : R2021 | Standard Test Method for Cathodic Disbondment Test of Pipeline Coatings (Attached Cell Method) (Withdrawn 2024) |
| ASTM G 62 : 1987 : R1998 | Standard Test Methods for Holiday Detection in Pipeline Coatings |
| ASTM D 5286 : 2020 | Standard Test Methods for Determination of Transfer Efficiency Under General Production Conditions for Spray Application of Paints |
| ASTM D 4752 : 2010 : R2015 | Standard Practice for Measuring MEK Resistance of Ethyl Silicate (Inorganic) Zinc-Rich Primers by Solvent Rub |
| ASTM D 2197 : 1998 | Standard Test Method for Adhesion of Organic Coatings by Scrape Adhesion |
| ASTM D 2354 : 2010 : R2023 | Standard Test Method for Minimum Film Formation Temperature (MFFT) of Emulsion Vehicles |
| ASTM D 6944 : 2015 | Standard Practice for Determining the Resistance of Cured Coatings to Thermal Cycling |
| ASTM D 5324 : 2016 : R2022 | Standard Guide for Testing Water-Borne Architectural Coatings |
| ASTM D 1212 : 1991 : R2020 | Standard Test Methods for Measurement of Wet Film Thickness of Organic Coatings |
| ASTM D 3134 : 2015 | Standard Practice for Establishing Color and Gloss Tolerances |
| ASTM D 5894 : 2021 | Standard Practice for Cyclic Salt Fog/UV Exposure of Painted Metal, (Alternating Exposures in a Fog/Dry Cabinet and a UV/Condensation Cabinet) |
| ASTM D 3359 : 1997 | Standard Test Methods for Measuring Adhesion by Tape Test |
| ASTM D 93 : 2019 | Standard Test Methods for Flash Point by Pensky-Martens Closed Cup Tester |
| ASTM D 2244 : 2016 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
| ASTM D 2200 : 2017 | Standard Practice for Use of Pictorial Surface Preparation Standards and Guides for Painting Steel Surfaces |
| ASTM E 84 : 2023 | Standard Test Method for Surface Burning Characteristics of Building Materials |
| ASTM D 6943 : 2015 | Standard Practice for Immersion Testing of Industrial Protective Coatings and Linings |
| ASTM D 1296 : 2001 : R2012 | Standard Test Method for Odor of Volatile Solvents and Diluents (Withdrawn 2021) |
| ASTM D 7868 : 2013 : R2017 | Standard Practice for Determining the Dry Fall (Fog) Properties of Protective Coatings |
| ASTM D 3363 : 2020 | Standard Test Method for Film Hardness by Pencil Test |
| ASTM G 20 : 2010 : R2019 | Standard Test Method for Chemical Resistance of Pipeline Coatings |
| ASTM G 154 : 2023 | Standard Practice for Operating Fluorescent Ultraviolet (UV) Lamp Apparatus for Exposure of Materials |
| ASTM G 62 : 2022 | Standard Test Methods for Holiday Detection in Pipeline Coatings |
| ASTM G 106 : 1989 : R2015 | Standard Practice for Verification of Algorithm and Equipment for Electrochemical Impedance Measurements |
| ASTM E 84 : 2021 | Standard Test Method for Surface Burning Characteristics of Building Materials |
| ASTM D 185 : 2007 : R2023 | Standard Test Methods for Coarse Particles in Pigments |
| ASTM D 4752 : 1998 | Standard Test Method for Measuring MEK Resistance of Ethyl Silicate (Inorganic) Zinc-Rich Primers by Solvent Rub |
| ASTM D 93 : 1990 : EDT 1 | Standard Test Methods for Flash Point by Pensky-Martens Closed Tester |
| ASTM G 8 : 2024 | Standard Test Methods for Cathodic Disbonding of Coated Steel |
| ASTM D 16 : 2019 | Standard Terminology for Paint, Related Coatings, Materials, and Applications |
| ASTM D 2697 : 2003 : R2014 | Standard Test Method for Volume Nonvolatile Matter in Clear or Pigmented Coatings |
| ASTM D 3278 : 1982 : EDT 1 | Standard Test Methods for Flash Point of Liquids by Setaflash Closed-Cup Apparatus |
| ASTM E 84 : 2022 | Standard Test Method for Surface Burning Characteristics of Building Materials |
| ASTM D 7091 : 2020 | Standard Practice for Nondestructive Measurement of Dry Film Thickness of Nonmagnetic Coatings Applied to Ferrous Metals and Nonmagnetic, Nonconductive Coatings Applied to Non-Ferrous Metals |
| ASTM D 3278 : 2021 | Standard Test Methods for Flash Point of Liquids by Small Scale Closed-Cup Apparatus |
| ASTM D 2247 : 2015 | Standard Practice for Testing Water Resistance of Coatings in 100 % Relative Humidity |
| ASTM D 5009 : 2002 : R2023 | Standard Test Method for Evaluating and Comparing Transfer Efficiency of Spray Applied Coatings Under Laboratory Conditions |
| ASTM D 968 : 2022 | Standard Test Methods for Abrasion Resistance of Organic Coatings by Falling Abrasive |
| ASTM D 3168 : 1985 : R2016 | Standard Practice for Qualitative Identification of Polymers in Emulsion Paints |
| ASTM D 2697 : 2003 : R2021 | Standard Test Method for Volume Nonvolatile Matter in Clear or Pigmented Coatings |
| ASTM D 1210 : 2005 : R2022 | Standard Test Method for Fineness of Dispersion of Pigment-Vehicle Systems by Hegman-Type Gage |
| ASTM D 2201 : 2023 | Standard Practice for Preparation of Zinc-Coated and Zinc-Alloy-Coated Steel Panels for Testing Paint and Related Coating Products |
| ASTM G 62 : 2023 | Standard Test Methods for Holiday Detection of Coatings used to Protect Pipelines |
| ASTM D 2354 : 2010 : R2018 | Standard Test Method for Minimum Film Formation Temperature (MFFT) of Emulsion Vehicles |
| ASTM D 5402 : 2019 | Standard Practice for Assessing the Solvent Resistance of Organic Coatings Using Solvent Rubs |
| ASTM D 1735 : 2014 | Standard Practice for Testing Water Resistance of Coatings Using Water Fog Apparatus |
| ASTM D 56 : 2021 : REV A | Standard Test Method for Flash Point by Tag Closed Cup Tester |
| ASTM D 1653 : 2013 : R2021 | Standard Test Methods for Water Vapor Transmission of Organic Coating Films |
| ASTM D 1731 : 2009 : R2014 | Standard Practices for Preparation of Hot-Dip Aluminum Surfaces for Painting |
| ASTM G 152 : 2013 : R2021 | Standard Practice for Operating Open Flame Carbon Arc Light Apparatus for Exposure of Nonmetallic Materials |
| ASTM D 2369 : 2020 | Standard Test Method for Volatile Content of Coatings |
| ASTM D 3359 : 2022 | Standard Test Methods for Rating Adhesion by Tape Test |
| ASTM E 84 : 2020 | Standard Test Method for Surface Burning Characteristics of Building Materials |
| ASTM D 1732 : 2003 : R2018 | Standard Practices for Preparation of Magnesium Alloy Surfaces for Painting |
| ASTM D 3960 : 1998 | Standard Practice for Determining Volatile Organic Compound (VOC) Content of Paints and Related Coatings |
| ASTM E 84 : 2021 : REV A | Standard Test Method for Surface Burning Characteristics of Building Materials |
| ASTM D 4214 : 2023 | Standard Test Methods for Evaluating the Degree of Chalking of Exterior Paint Films |
| ASTM D 4541 : 2017 | Standard Test Method for Pull-Off Strength of Coatings Using Portable Adhesion Testers |
| ASTM D 1296 : 2023 | Standard Test Method for Odor of Volatile Solvents and Diluents |
| ASTM D 5327 : 1997 : R2021 : EDT 1 | Standard Practice for Evaluating and Comparing Transfer Efficiency of Spray Applied Coatings Under General Laboratory Conditions |
| ASTM D 5178 : 1998 | Standard Test Method for Mar Resistance of Organic Coatings |
| ASTM D 1210 : 2005 : R2014 | Standard Test Method for Fineness of Dispersion of Pigment-Vehicle Systems by Hegman-Type Gage |
| ASTM D 1535 : 2014 : R2018 | Standard Practice for Specifying Color by the Munsell System |
| ASTM G 155 : 2021 | Standard Practice for Operating Xenon Arc Lamp Apparatus for Exposure of Materials |
| ASTM D 4541 : 2022 | Standard Test Method for Pull-Off Strength of Coatings Using Portable Adhesion Testers |
| ASTM D 822 : 2023 | Standard Practice for Filtered Open-Flame Carbon-Arc Exposures of Paint and Related Coatings |
| ASTM D 56 : 2016 : REV A | Standard Test Method for Flash Point by Tag Closed Cup Tester |
| ASTM G 8 : 1996 : R2019 | Standard Test Methods for Cathodic Disbonding of Pipeline Coatings |
| ASTM G 95 : 2007 : R2013 | Standard Test Method for Cathodic Disbondment Test of Pipeline Coatings (Attached Cell Method) |
| ASTM D 562 : 2010 : R2018 | Standard Test Method for Consistency of Paints Measuring Krebs Unit (KU) Viscosity Using a Stormer-Type Viscometer |
| ASTM D 870 : 2015 : R2020 : EDT 1 | Standard Practice for Testing Water Resistance of Coatings Using Water Immersion |
| ASTM D 4287 : 2000 : R2019 | Standard Test Method for High-Shear Viscosity Using a Cone/Plate Viscometer |
| ASTM D 1212 : 1991 : R2001 | Standard Test Methods for Measurement of Wet Film Thickness of Organic Coatings |
| ASTM D 6132 : 2013 : R2017 | Standard Test Method for Nondestructive Measurement of Dry Film Thickness of Applied Organic Coatings Using an Ultrasonic Coating Thickness Gage |
| ASTM D 5894 : 2016 | Standard Practice for Cyclic Salt Fog/UV Exposure of Painted Metal, (Alternating Exposures in a Fog/Dry Cabinet and a UV/Condensation Cabinet) |
| ASTM D 1005 : 1995 : R2013 | Standard Test Method for Measurement of Dry-Film Thickness of Organic Coatings Using Micrometers |
| ASTM D 4212 : 2016 : R2023 | Standard Test Method for Viscosity by Dip-Type Viscosity Cups |
| ASTM D 5065 : 2017 | Standard Guide for Assessing the Condition of Aged Coatings on Steel Surfaces |
| ASTM D 2574 : 2016 : R2020 : EDT 1 | Standard Test Method for Resistance of Emulsion Paints in the Container to Attack by Microorganisms |
| ASTM D 16 : 2024 | Standard Terminology for Paint, Related Coatings, Materials, and Applications |
| ASTM D 4214 : 2007 : R2015 | Standard Test Methods for Evaluating the Degree of Chalking of Exterior Paint Films |
| ASTM D 5162 : 2015 | Standard Practice for Discontinuity (Holiday) Testing of Nonconductive Protective Coating on Metallic Substrates |
| ASTM B 117 : 2019 | Standard Practice for Operating Salt Spray (Fog) Apparatus |
| ASTM D 5031 : 2023 | Standard Practice for Enclosed Carbon-Arc Exposure Tests of Paint and Related Coatings |
| ASTM D 2247 : 2015 : R2020 | Standard Practice for Testing Water Resistance of Coatings in 100 % Relative Humidity |
| ASTM G 153 : 2013 : R2021 | Standard Practice for Operating Enclosed Carbon Arc Light Apparatus for Exposure of Nonmetallic Materials |
| ASTM D 2369 : 2024 | Standard Test Method for Volatile Content of Coatings |
| ASTM D 3924 : 2024 | Standard Specification for Standard Environment for Conditioning and Testing Paint, Varnish, Lacquer, and Related Materials |
| ASTM D 3134 : 2015 : R2019 | Standard Practice for Establishing Color and Gloss Tolerances |
| ASTM D 1730 : 2009 : R2020 | Standard Practices for Preparation of Aluminum and Aluminum-Alloy Surfaces for Painting |
| ASTM D 870 : 2015 : R2020 | Standard Practice for Testing Water Resistance of Coatings Using Water Immersion |
| ASTM D 4752 : 2020 | Standard Practice for Measuring MEK Resistance of Ethyl Silicate (Inorganic) Zinc-Rich Primers by Solvent Rub |
| ASTM D 3925 : 2002 : R2022 | Standard Practice for Sampling Liquid Paints and Related Pigmented Coatings |
| ASTM D 7055 : 2019 | Standard Practice for Preparation (by Abrasive Blast Cleaning) of Hot-Rolled Carbon Steel Panels for Testing of Coatings |
| ASTM D 56 : 2021 | Standard Test Method for Flash Point by Tag Closed Cup Tester |
| ASTM D 4958 : 2010 : R2016 | Standard Test Method for Comparison of the Brush Drag of Latex Paints |
| ASTM G 106 : 1989 : R2023 | Standard Practice for Verification of Algorithm and Equipment for Electrochemical Impedance Measurements |
| ASTM G 85 : 1998 | Standard Practice for Modified Salt Spray (Fog) Testing |
| ASTM D 5065 : 2017 : R2021 | Standard Guide for Assessing the Condition of Aged Coatings on Steel Surfaces |
| ASTM D 3792 : 2016 | Standard Test Method for Water Content of Coatings by Direct Injection Into a Gas Chromatograph |
| ASTM D 823 : 2018 | Standard Practices for Producing Films of Uniform Thickness of Paint, Coatings and Related Products on Test Panels |
| ASTM G 152 : 2013 | Standard Practice for Operating Open Flame Carbon Arc Light Apparatus for Exposure of Nonmetallic Materials |
| ASTM G 80 : 2007 | Standard Test Method for Specific Cathodic Disbonding of Pipeline Coatings (Withdrawn 2013) |
| ASTM G 20 : 2010 : R2024 | Standard Test Method for Chemical Resistance of Pipeline Coatings |
| ASTM D 2244 : 2022 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
| ASTM G 62 : 2014 | Standard Test Methods for Holiday Detection in Pipeline Coatings |
| ASTM D 1308 : 1987 : R1998 | Standard Test Method for Effect of Household Chemicals on Clear and Pigmented Organic Finishes |
| ASTM E 84 : 2023 : REV B | Standard Test Method for Surface Burning Characteristics of Building Materials |
| ASTM D 5895 : 2020 | Standard Test Methods for Evaluating Drying or Curing During Film Formation of Organic Coatings Using Mechanical Recorders |
| ASTM D 7091 : 2021 | Standard Practice for Nondestructive Measurement of Dry Film Thickness of Nonmagnetic Coatings Applied to Ferrous Metals and Nonmagnetic, Nonconductive Coatings Applied to Non-Ferrous Metals |
| ASTM D 93 : 2000 | Standard Test Methods for Flash-Point by Pensky-Martens Closed Cup Tester |
| ASTM D 6677 : 2018 | Standard Test Method for Evaluating Adhesion by Knife |
| ASTM D 4587 : 2023 | Standard Practice for Fluorescent UV-Condensation Exposures of Paint and Related Coatings |
| ASTM G 155 : 2013 | Standard Practice for Operating Xenon Arc Light Apparatus for Exposure of Non-Metallic Materials |
| ASTM D 3912 : 2010 : R2023 | Standard Test Method for Chemical Resistance of Coatings and Linings for Use in Nuclear Power Plants |
| ASTM D 3134 : 1997 | Standard Practice for Establishing Color and Gloss Tolerances |
| ASTM D 5402 : 2019 : R2024 | Standard Practice for Assessing the Solvent Resistance of Organic Coatings Using Solvent Rubs |
| ASTM D 6132 : 2013 : R2022 | Standard Test Method for Nondestructive Measurement of Dry Film Thickness of Applied Organic Coatings Using an Ultrasonic Coating Thickness Gage |
| ASTM D 93 : 1985 | Standard Test Method for Flash Point by Pensky-Martens Closed Tester |
| ASTM D 4752 : 2020 : R2024 | Standard Practice for Measuring MEK Resistance of Ethyl Silicate (Inorganic) Zinc-Rich Primers by Solvent Rub |
| ASTM D 1729 : 2022 | Standard Practice for Visual Appraisal of Colors and Color Differences of Diffusely-Illuminated Opaque Materials |
| ASTM D 3792 : 2016 : R2022 | Standard Test Method for Water Content of Coatings by Direct Injection Into a Gas Chromatograph |
| ASTM D 56 : 2022 | Standard Test Method for Flash Point by Tag Closed Cup Tester |
| ASTM D 4287 : 2000 : R2023 | Standard Test Method for High-Shear Viscosity Using a Cone/Plate Viscometer |
| ASTM D 2201 : 2022 | Standard Practice for Preparation of Zinc-Coated and Zinc-Alloy-Coated Steel Panels for Testing Paint and Related Coating Products |
| ASTM D 4400 : 1999 | Standard Test Method for Sag Resistance of Paints Using a Multinotch Applicator |
| ASTM D 2197 : 2016 | Standard Test Method for Adhesion of Organic Coatings by Scrape Adhesion |
| ASTM D 6677 : 2018 : R2022 | Standard Test Method for Evaluating Adhesion by Knife |
| ASTM D 6944 : 2015 : R2020 | Standard Practice for Determining the Resistance of Cured Coatings to Thermal Cycling |
| ASTM D 5178 : 2016 | Standard Test Method for Mar Resistance of Organic Coatings |
| ASTM D 3359 : 2023 | Standard Test Methods for Rating Adhesion by Tape Test |
| ASTM D 4138 : 2007 : REV A : R2017 | Standard Practices for Measurement of Dry Film Thickness of Protective Coating Systems by Destructive, Cross-Sectioning Means |
| ASTM D 1732 : 2003 : R2023 | Standard Practices for Preparation of Magnesium Alloy Surfaces for Painting |
| ASTM G 113 : 2016 | Standard Terminology Relating to Natural and Artificial Weathering Tests of Nonmetallic Materials |
| ASTM D 1731 : 2009 : R2020 | Standard Practices for Preparation of Hot-Dip Aluminum Surfaces for Painting |
| ASTM D 2805 : 2011 : R2023 | Standard Test Method for Hiding Power of Paints by Reflectometry |
| ASTM D 2794 : 1993 : R2019 | Standard Test Method for Resistance of Organic Coatings to the Effects of Rapid Deformation (Impact) |
| ASTM D 56 : 1987 | Standard Test Method for Flash Point by Tag Closed Tester |
| ASTM D 1653 : 2013 | Standard Test Methods for Water Vapor Transmission of Organic Coating Films |
| ASTM D 4587 : 2011 : R2019 : EDT 1 | Standard Practice for Fluorescent UV-Condensation Exposures of Paint and Related Coatings |
| ASTM D 7868 : 2021 | Standard Practice for Determining the Dry Fall (Fog) Properties of Protective Coatings |
| ASTM D 1474 : 1998 | Standard Test Methods for Indentation Hardness of Organic Coatings |
| ASTM E 84 : 2023 : REV A | Standard Test Method for Surface Burning Characteristics of Building Materials |
| ASTM D 5009 : 2002 : R2017 | Standard Test Method for Evaluating and Comparing Transfer Efficiency of Spray Applied Coatings Under Laboratory Conditions |
| ASTM D 609 : 2017 | Standard Practice for Preparation of Cold-Rolled Steel Panels for Testing Paint, Varnish, Conversion Coatings, and Related Coating Products |
| ASTM D 2371 : 2019 | Standard Test Method for Pigment Content of Solvent-Reducible Paints |
| ASTM D 1535 : 2014 : R2023 | Standard Practice for Specifying Color by the Munsell System |
| ASTM D 7187 : 2015 | Standard Test Method for Measuring Mechanistic Aspects of Scratch/Mar Behavior of Paint Coatings by Nanoscratching |
| ASTM D 1212 : 1991 | Standard Test Methods for Measurement of Wet Film Thickness of Organic Coatings |
| ASTM D 2247 : 2015 : R2020 : EDT 1 | Standard Practice for Testing Water Resistance of Coatings in 100 % Relative Humidity |
| ASTM D 562 : 2010 : R2023 | Standard Test Method for Consistency of Paints Measuring Krebs Unit (KU) Viscosity Using a Stormer-Type Viscometer |
| ASTM D 4017 : 2022 | Standard Test Method for Water in Paints and Paint Materials by Karl Fischer Method |
| ASTM D 968 : 2017 | Standard Test Methods for Abrasion Resistance of Organic Coatings by Falling Abrasive |
| ASTM D 2803 : 2009 : R2015 | Standard Guide for Testing Filiform Corrosion Resistance of Organic Coatings on Metal |
| ASTM D 6943 : 2015 : R2019 | Standard Practice for Immersion Testing of Industrial Protective Coatings and Linings |
| ASTM D 6943 : 2015 : R2024 | Standard Practice for Immersion Testing of Industrial Protective Coatings and Linings |
| ASTM D 5324 : 2016 | Standard Guide for Testing Water-Borne Architectural Coatings |
| ASTM D 2803 : 2009 : R2020 | Standard Guide for Testing Filiform Corrosion Resistance of Organic Coatings on Metal |
| ASTM D 3359 : 2017 | Standard Test Methods for Rating Adhesion by Tape Test |
| ASTM D 2369 : 2010 : R2015 : EDT 1 | Standard Test Method for Volatile Content of Coatings |
| ASTM D 2574 : 2016 : R2024 | Standard Test Method for Resistance of Emulsion Paints in the Container to Attack by Microorganisms |
| ASTM D 93 : 1997 | Standard Test Methods for Flash-Point by Pensky-Martens Closed Cup Tester |
| ASTM D 823 : 2018 : R2022 | Standard Practices for Producing Films of Uniform Thickness of Paint, Coatings and Related Products on Test Panels |
| ASTM D 3925 : 2002 : R2015 | Standard Practice for Sampling Liquid Paints and Related Pigmented Coatings |
| ASTM D 5064 : 2016 : REV A : R2021 | Standard Practice for Conducting a Patch Test to Assess Coating Compatibility |
| ASTM D 5286 : 2001 : R2017 | Standard Test Methods for Determination of Transfer Efficiency Under General Production Conditions for Spray Application of Paints |
| ASTM D 3912 : 2010 : R2017 | Standard Test Method for Chemical Resistance of Coatings and Linings for Use in Nuclear Power Plants |
| ASTM D 16 : 2023 | Standard Terminology for Paint, Related Coatings, Materials, and Applications |
| ASTM G 113 : 2022 | Standard Terminology Relating to Natural and Artificial Weathering Tests of Nonmetallic Materials |
| ASTM D 4060 : 2019 | Standard Test Method for Abrasion Resistance of Organic Coatings by the Taber Abraser |
| ASTM D 2197 : 2016 : R2022 | Standard Test Method for Adhesion of Organic Coatings by Scrape Adhesion |
| ASTM D 3278 : 1996 : R2011 | Standard Test Methods for Flash Point of Liquids by Small Scale Closed-Cup Apparatus (Withdrawn 2020) |
| ASTM D 93 : 2018 | Standard Test Methods for Flash Point by Pensky-Martens Closed Cup Tester |
| ASTM D 4212 : 2016 | Standard Test Method for Viscosity by Dip-Type Viscosity Cups |
| ASTM D 3924 : 2016 : R2019 | Standard Specification for Standard Environment for Conditioning and Testing Paint, Varnish, Lacquer, and Related Materials |
| ASTM D 2803 : 1993 | Standard Guide for Testing Filiform Corrosion Resistance of Organic Coatings on Metal (Withdrawn 2002) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.