ASTM D 6152/D6152M : 2012 : R2018
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for SEBS-Modified Mopping Asphalt Used in Roofing
Hardcopy , PDF
05-08-2024
English
08-09-2018
Committee |
D 08
|
DocumentType |
Standard
|
Pages |
3
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
1.1This specification covers SEBS (styrene-ethylene-butylene-styrene)-modified asphalt intended for use in built-up roof construction, construction of some modified bitumen systems, construction of bituminous vapor retarder systems, and for adhering insulation boards used in various types of roof systems.
1.2This specification is intended as a material specification. Issues regarding the suitability of specific roof constructions or application techniques are beyond its scope.
1.3The specified tests and property values used to characterize SEBS-modified asphalt are intended to establish minimum properties. In place system design criteria or performance attributes are factors beyond the scope of this specification.
1.4The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.5This standard does not purport to address the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM D 6622/D6622M : 2020 | Standard Guide for Application of Fully Adhered Hot-Applied Reinforced Waterproofing Systems |
ASTM C 981 : 2020 | Standard Guide for Design of Built-Up Bituminous Membrane Waterproofing Systems for Building Decks |
ASTM D 1079 : 2018 : EDT 1 | Standard Terminology Relating to Roofing and Waterproofing |
ASTM D 1079 : 2016 | Standard Terminology Relating to Roofing and Waterproofing |
ASTM D 3111 : 1999 | Standard Test Method for Flexibility Determination of Hot-Melt Adhesives by Mandrel Bend Test Method |
ASTM D 3111 : 2010 : R2018 | Standard Test Method for Flexibility Determination of Hot-Melt Adhesives by Mandrel Bend Test Method |
ASTM D 2042 : 1997 | Standard Test Method for Solubility of Asphalt Materials in Trichloroethylene |
ASTM D 312/D312M : 2016 : REV A | Standard Specification for Asphalt Used in Roofing |
ASTM D 140/D140M : 2016 : R2023 | Standard Practice for Sampling Asphalt Materials |
ASTM D 412 : 2016 : EDT 1 | Standard Test Methods for Vulcanized Rubber and Thermoplastic Elastomers—Tension |
ASTM D 312/D312M : 2016 : REV A : R2023 | Standard Specification for Asphalt Used in Roofing |
ASTM D 36/D36M : 2014 : EDT 1 | Standard Test Method for Softening Point of Bitumen (Ring-and-Ball Apparatus) |
ASTM D 2042 : 2015 | Standard Test Method for Solubility of Asphalt Materials in Trichloroethylene |
ASTM D 1079 : 2018 | Standard Terminology Relating to Roofing and Waterproofing |
ASTM D 412 : 2016 | Standard Test Methods for Vulcanized Rubber and Thermoplastic Elastomers—Tension |
ASTM D 140/D140M : 2016 | Standard Practice for Sampling Asphalt Materials |
ASTM D 412 : 2016 : R2021 | Standard Test Methods for Vulcanized Rubber and Thermoplastic Elastomers—Tension |
ASTM D 1079 : 2000 : REV A | Standard Terminology Relating to Roofing, Waterproofing, and Bituminous Materials |
ASTM D 2042 : 2022 | Standard Test Method for Solubility of Asphalt Materials in Trichloroethylene or Toluene |
ASTM D 3111 : 2019 | Standard Practice for Flexibility Determination of Hot-Melt Adhesives by Mandrel Bend Test |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.