ASTM D 5967 : 2017
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Evaluation of Diesel Engine Oils in T-8 Diesel Engine
Hardcopy , PDF
11-14-2019
English
05-01-2017
This test method covers an engine test procedure for evaluating diesel engine oils for performance characteristics, including viscosity increase and soot concentrations (loading).
Committee |
D 02
|
DocumentType |
Test Method
|
Pages |
22
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
1.1This test method covers an engine test procedure for evaluating diesel engine oils for performance characteristics, including viscosity increase and soot concentrations (loading).2 This test method is commonly referred to as the Mack T-8.
1.2This test method also provides the procedure for running an extended length T-8 test, which is commonly referred to as the T-8E and an abbreviated length test, which is commonly referred to as T-8A. The procedures for the T-8E and the T-8A are identical to the T-8 with the exception of the items specifically listed in Annex A8 and Annex A9 respectively. Additionally, the procedure modifications listed in Annex A8 and Annex A9 refer to the corresponding section of the T-8 procedure.
1.3The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.3.1Exceptions—Where there is no direct SI equivalent such as the units for screw threads, National Pipe Threads/diameters, tubing size, sole source equipment suppliers, and oil consumption in grams per kilowatt-hour.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. See Annex A6 for specific safety precautions.
1.5A Table of Contents follows:
Scope | 1 |
Referenced Documents | 2 |
Terminology | 3 |
Summary of Test Method | 4 |
Significance and Use | 5 |
Apparatus | 6 |
General Description | 6.1 |
The Test Engine | 6.2 |
Mack Test Engine | 6.2.1 |
Engine Cooling System | 6.2.2 |
Engine Oil System | 6.2.3 |
Auxiliary Oil System | 6.2.4 |
Crankcase Aspiration | 6.2.5 |
Blowby Meter | 6.2.6 |
Air Supply and Filtration | 6.2.7 |
Fuel Supply | 6.2.8 |
Intake Manifold Temperature Control | 6.2.9 |
Engine Fluids | 7 |
Test Oil | 7.1 |
Test Fuel | 7.2 |
Engine Coolant | 7.3 |
Cleaning Materials | 7.4 |
Preparation of Apparatus at Rebuild | 8 |
Cleaning of Parts | 8.1 |
Valves, Seats, Guides, and Springs | 8.2 |
Cylinder Liner, Piston, and Piston Ring Assembly | 8.3 |
Injectors and Injection Pump | 8.4 |
Assembly Instructions | 8.5 |
Measurements | 8.6 |
Laboratory and Engine Test Stand Calibration/Non-Reference | 9 |
Calibration Frequency | 9.1 |
Calibration Reference Oils | 9.2 |
Test Numbering | 9.3 |
New Laboratories and New Test Stands | 9.4 |
Calibrated Laboratories and Test Stands | 9.5 |
Calibration Test Acceptance | 9.6 |
Failing Calibration Tests | 9.7 |
Non-Reference Oil Test Requirements | 9.8 |
Procedure | 10 |
Pretest Procedure | 10.1 |
Engine Start-Up | 10.2 |
Engine Shutdown | 10.3 |
Test Cycle | 10.4 |
Oil Addition/Drain | 10.5 |
Oil Samples | 10.6 |
Oil Consumption Calculations | 10.7 |
Fuel Samples | 10.8 |
Periodic Measurements | 10.9 |
Blowby | 10.10 |
Centrifugal Oil Filter Mass Gain | 10.11 |
Oil Filter Δ P Calculation | 10.12 |
Post Test | 10.13 |
Inspection of Fuel and Oil During Test | 11 |
Oil Inspection | 11.1 |
Fuel Inspections | 11.2 |
Oil Consumption | 11.3 |
Report | 12 |
Reporting Test Results | 12.1 |
Deviations from Test Operational Limits | 12.2 |
Electronic Transmission of Test Results | 12.3 |
Plots of Operational Data | 12.4 |
Precision and Bias | 13 |
Precision | 13.1 |
Bias | 13.2 |
Keywords | 14 |
Annexes | |
Report Forms | Annex A1 |
Sensor Locations | Annex A2 |
Kinematic Viscosity At 100°C For Test Method D5967 Samples | Annex A3 |
Enhanced Thermal Gravimetric Analysis (TGA) Procedure | Annex A4 |
Procurement of Test Materials | Annex A5 |
Safety Precautions | Annex A6 |
Data Dictionary | Annex A7 |
T-8E Extended Length Test Requirements | Annex A8 |
T-8A Abbreviated Length Test Requirements | Annex A9 |
1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM D 7422 : 2019 | Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine |
ASTM D 7156 : 2019 | Standard Test Method for Evaluation of Diesel Engine Oils in the T-11 Exhaust Gas Recirculation Diesel Engine |
ASTM D 8048 : 2019 : REV A | Standard Test Method for Evaluation of Diesel Engine Oils in T-13 Diesel Engine |
ASTM D 4485 : 2018 : REV A | Standard Specification for Performance of Active API Service Category Engine Oils |
ASTM D 7484 : 2019 | Standard Test Method for Evaluation of Automotive Engine Oils for Valve-Train Wear Performance in Cummins ISB Medium-Duty Diesel Engine |
ASTM D 7549 : 2019 | Standard Test Method for Evaluation of Heavy-Duty Engine Oils under High Output Conditions—Caterpillar C13 Test Procedure |
ASTM D 8074 : 2018 | Standard Test Method for Evaluation of Diesel Engine Oils in DD13 Diesel Engine |
ASTM D 7156 : 2017 | Standard Test Method for Evaluation of Diesel Engine Oils in the T-11 Exhaust Gas Recirculation Diesel Engine |
ASTM D 6923 : 2018 | Standard Test Method for Evaluation of Engine Oils in a High Speed, Single-Cylinder Diesel Engine—Caterpillar 1R Test Procedure |
ASTM D 7844 : 2018 | Standard Test Method for Condition Monitoring of Soot in In-Service Lubricants by Trend Analysis using Fourier Transform Infrared (FT-IR) Spectrometry |
ASTM D 7317 : 2007 : R2019 | Standard Test Method for Coagulated Pentane Insolubles in Used Lubricating Oils by Paper Filtration (LMOA Method) |
ASTM D 7483 : 2013 : REV A : R2017 | Standard Test Method for Determination of Dynamic Viscosity and Derived Kinematic Viscosity of Liquids by Oscillating Piston Viscometer |
ASTM D 6987/D6987M : 2013 : REV A | Standard Test Method for Evaluation of Diesel Engine Oils in T-10 Exhaust Gas Recirculation Diesel Engine (Withdrawn 2022) |
ASTM D 8048 : 2019 | Standard Test Method for Evaluation of Diesel Engine Oils in T-13 Diesel Engine |
ASTM D 6895 : 2017 | Standard Test Method for Rotational Viscosity of Heavy Duty Diesel Drain Oils at 100 °C |
ASTM D 7422 : 2017 : REV A | Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine |
ASTM D 7583 : 2016 | Standard Test Method for John Deere Coolant Cavitation Test |
ASTM D 7596 : 2014 | Standard Test Method for Automatic Particle Counting and Particle Shape Classification of Oils Using a Direct Imaging Integrated Tester |
ASTM D 7686 : 2019 | Standard Test Method for Field-Based Condition Monitoring of Soot in In-Service Lubricants Using a Fixed-Filter Infrared (IR) Instrument |
ASTM D 7686 : 2011 | Standard Test Method for Field-Based Condition Monitoring of Soot in In-Service Lubricants Using a Fixed-Filter Infrared (IR) Instrument |
ASTM D 4175 : 2014 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
ASTM D 4485 : 2003 : REV A | Standard Specification for Performance of Engine Oils |
ASTM D 2622 : 1992 : EDT 1 | Standard Test Method for Sulfur in Petroleum Products by X-Ray Spectrometry |
ASTM D 4175 : 2009 : REV A : EDT 1 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
ASTM D 7422 : 2012 | Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine |
ASTM D 4175 : 2008 : REV B : EDT 1 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
ASTM D 5453 : 2009 | Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence |
ASTM D 2274 : 2010 | Standard Test Method for Oxidation Stability of Distillate Fuel Oil (Accelerated Method) |
ASTM D 4485 : 2006 | Standard Specification for Performance of Engine Oils |
ASTM D 6278 : 1998 | Standard Test Method for Shear Stability of Polymer Containing Fluids Using a European Diesel Injector Apparatus |
ASTM D 2622 : 1987 : EDT 1 | Standard Test Method for Sulfur in Petroleum Products by X-Ray Spectrometry |
ASTM D 2709 : 1996 : R2011 : EDT 1 | Standard Test Method for Water and Sediment in Middle Distillate Fuels by Centrifuge |
ASTM D 4175 : 2005 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
ASTM D 2709 : 1996 : EDT 2 | Standard Test Method for Water and Sediment in Middle Distillate Fuels by Centrifuge |
ASTM D 4485 : 2011 : REV C | Standard Specification for Performance of Active API Service Category Engine Oils |
ASTM D 1319 : 1989 | Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Absorption |
ASTM D 4175 : 2005 : EDT 2 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
ASTM D 1319 : 2008 | Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption |
ASTM D 4485 : 2001 | Standard Specification for Performance of Engine Oils |
ASTM D 5453 : 2008 : REV B | Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence |
ASTM D 5453 : 2000 | Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Motor Fuels and Oils by Ultraviolet Fluorescence |
ASTM D 7422 : 2009 | Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine |
ASTM D 5185 : 1997 | Standard Test Method for Determination of Additive Elements, Wear Metals, and Contaminants in Used Lubricating Oils and Determination of Selected Elements in Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES) |
ASTM D 4175 : 2015 : REV C | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
ASTM D 4175 : 2017 : REV A : EDT 1 | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
ASTM D 2274 : 2001 | Standard Test Method for Oxidation Stability of Distillate Fuel Oil (Accelerated Method) |
ASTM D 4485 : 2003 | Standard Specification for Performance of Engine Oils |
ASTM D 4052 : 1996 : R2002 : EDT 1 | Standard Test Method for Density and Relative Density of Liquids by Digital Density Meter |
ASTM D 4485 : 2008 | Standard Specification for Performance of Engine Oils |
ASTM D 2709 : 1996 : R2006 | Standard Test Method for Water and Sediment in Middle Distillate Fuels by Centrifuge |
ASTM D 4485 : 2015 | Standard Specification for Performance of Active API Service Category Engine Oils |
ASTM D 5453 : 2004 | Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Motor Fuels and Oils by Ultraviolet Fluorescence |
ASTM D 1319 : 2018 | Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption |
ASTM D 4485 : 2005 : REV A | Standard Specification for Performance of Engine Oils |
ASTM D 7422 : 2016 : REV A | Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine |
ASTM D 4175 : 2008 : REV A | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
ASTM D 5453 : 2012 | Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence |
ASTM D 4294 : 2010 | Standard Test Method for Sulfur in Petroleum and Petroleum Products by Energy Dispersive X-ray Fluorescence Spectrometry |
ASTM D 2500 : 2016 : REV B | Standard Test Method for Cloud Point of Petroleum Products and Liquid Fuels |
ASTM D 4052 : 2018 : REV A | Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter |
ASTM D 1319 : 2014 | Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption |
ASTM D 4175 : 2017 : REV B | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
ASTM D 4175 : 2009 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
ASTM D 4485 : 2011 : REV A | Standard Specification for Performance of Active API Service Category Engine Oils |
ASTM D 2622 : 1998 | Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry |
ASTM D 2500 : 2016 : REV A | Standard Test Method for Cloud Point of Petroleum Products and Liquid Fuels |
ASTM D 2274 : 2003 : REV A : R2008 | Standard Test Method for Oxidation Stability of Distillate Fuel Oil (Accelerated Method) |
ASTM D 2500 : 2016 | Standard Test Method for Cloud Point of Petroleum Products |
ASTM D 1319 : 1999 | Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption |
ASTM D 7422 : 2015 | Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine |
ASTM D 4485 : 2018 | Standard Specification for Performance of Active API Service Category Engine Oils |
ASTM D 5185 : 2005 | Standard Test Method for Determination of Additive Elements, Wear Metals, and Contaminants in Used Lubricating Oils and Determination of Selected Elements in Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES) |
ASTM D 4737 : 2009 | Standard Test Method for Calculated Cetane Index by Four Variable Equation |
ASTM D 4175 : 2009 : REV A : EDT 4 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
ASTM D 4175 : 2009 : REV A : EDT 3 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
ASTM D 4052 : 2009 | Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter |
ASTM D 5453 : 2008 : REV A | Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence |
ASTM D 5185 : 2002 | Standard Test Method for Determination of Additive Elements, Wear Metals, and Contaminants in Used Lubricating Oils and Determination of Selected Elements in Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES) |
ASTM D 4485 : 2011 : REV B | Standard Specification for Performance of Active API Service Category Engine Oils |
ASTM D 2622 : 2008 | Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry |
ASTM D 4485 : 2016 | Standard Specification for Performance of Active API Service Category Engine Oils |
ASTM D 4175 : 2018 | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
ASTM D 4485 : 2007 | Standard Specification for Performance of Engine Oils |
ASTM D 7422 : 2014 : REV A | Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine |
ASTM D 4485 : 2010 | Standard Specification for Performance of Engine Oils |
ASTM D 5185 : 2018 | Standard Test Method for Multielement Determination of Used and Unused Lubricating Oils and Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES) |
ASTM D 4485 : 2001 : REV A | Standard Specification for Performance of Engine Oils |
ASTM D 7422 : 2010 : REV A | Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine |
ASTM D 7422 : 2008 | Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine |
ASTM D 4175 : 2001 : EDT 1 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
ASTM D 1319 : 2002 : REV A | Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption |
ASTM D 2274 : 2003 | Standard Test Method for Oxidation Stability of Distillate Fuel Oil (Accelerated Method) |
ASTM D 5453 : 2005 | Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Motor Fuels and Oils by Ultraviolet Fluorescence |
ASTM D 7422 : 2017 : REV A | Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine |
ASTM D 2709 : 2016 | Standard Test Method for Water and Sediment in Middle Distillate Fuels by Centrifuge |
ASTM D 4175 : 2001 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
ASTM D 4175 : 2005 : EDT 1 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
ASTM D 2500 : 1999 | Standard Test Method for Cloud Point of Petroleum Products |
ASTM D 2500 : 2002 : EDT 1 | Standard Test Method for Cloud Point of Petroleum Products |
ASTM D 2500 : 2005 | Standard Test Method for Cloud Point of Petroleum Products |
ASTM D 4175 : 2002 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
ASTM D 5185 : 2013 : EDT 1 | Standard Test Method for Multielement Determination of Used and Unused Lubricating Oils and Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES) |
ASTM D 4485 : 2004 | Standard Specification for Performance of Engine Oils |
ASTM D 5453 : 2006 | Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence |
ASTM D 2500 : 2002 | Standard Test Method for Cloud Point of Petroleum Products |
ASTM D 2500 : 2011 | Standard Test Method for Cloud Point of Petroleum Products |
ASTM D 2500 : 2009 | Standard Test Method for Cloud Point of Petroleum Products |
ASTM D 4294 : 2008 | Standard Test Method for Sulfur in Petroleum and Petroleum Products by Energy Dispersive X-ray Fluorescence Spectrometry |
ASTM D 4175 : 2015 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
ASTM D 4485 : 2000 | Standard Specification for Performance of Engine Oils |
ASTM D 4175 : 2002 : REV A : EDT 2 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
ASTM D 2500 : 2017 | Standard Test Method for Cloud Point of Petroleum Products and Liquid Fuels |
ASTM D 4052 : 2011 | Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter |
ASTM D 1319 : 2003 | Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption |
ASTM D 4052 : 2016 | Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter |
ASTM D 7422 : 2013 | Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine |
ASTM D 4485 : 2015 : REV A | Standard Specification for Performance of Active API Service Category Engine Oils |
ASTM D 5185 : 2013 | Standard Test Method for Multielement Determination of Used and Unused Lubricating Oils and Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES) |
ASTM D 2622 : 2003 | Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry |
ASTM D 5453 : 2016 | Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence |
ASTM D 4294 : 2008 : REV A | Standard Test Method for Sulfur in Petroleum and Petroleum Products by Energy Dispersive X-ray Fluorescence Spectrometry |
ASTM D 1319 : 2010 | Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption |
ASTM D 4175 : 2009 : REV A : EDT 5 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
ASTM D 4175 : 2016 : REV C | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
ASTM D 4737 : 2009 : REV A | Standard Test Method for Calculated Cetane Index by Four Variable Equation |
ASTM D 4175 : 2015 : REV B | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
ASTM D 7422 : 2015 : REV A | Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine |
ASTM D 6278 : 2017 | Standard Test Method for Shear Stability of Polymer Containing Fluids Using a European Diesel Injector Apparatus |
ASTM D 4294 : 2002 | Standard Test Method for Sulfur in Petroleum Products by Energy-Dispersive X-Ray Fluorescence Spectroscopy |
ASTM D 4175 : 2015 : REV A | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
ASTM D 4485 : 2006 : REV A | Standard Specification for Performance of Engine Oils |
ASTM D 4737 : 2010 : R2016 | Standard Test Method for Calculated Cetane Index by Four Variable Equation |
ASTM D 5453 : 2003 | Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Motor Fuels and Oils by Ultraviolet Fluorescence |
ASTM D 2274 : 1994 : R1999 : EDT 1 | Standard Test Method for Oxidation Stability of Distillate Fuel Oil (Accelerated Method) |
ASTM D 4175 : 2009 : REV A | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
ASTM D 4175 : 2016 : REV B | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
ASTM D 7422 : 2016 | Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine |
ASTM D 2500 : 2017 : REV A | Standard Test Method for Cloud Point of Petroleum Products and Liquid Fuels |
ASTM D 7422 : 2011 | Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine |
ASTM D 4175 : 2002 : REV A : EDT 1 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
ASTM D 4175 : 2008 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
ASTM D 7422 : 2010 | Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine |
ASTM D 6278 : 2017 : EDT 1 | Standard Test Method for Shear Stability of Polymer Containing Fluids Using a European Diesel Injector Apparatus |
ASTM D 4737 : 2003 | Standard Test Method for Calculated Cetane Index by Four Variable Equation |
ASTM D 4175 : 2002 : REV A | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
ASTM D 4294 : 2016 : EDT 1 | Standard Test Method for Sulfur in Petroleum and Petroleum Products by Energy Dispersive X-ray Fluorescence Spectrometry |
ASTM D 5453 : 2016 : EDT 1 | Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence |
ASTM D 6278 : 2012 : EDT 1 | Standard Test Method for Shear Stability of Polymer Containing Fluids Using a European Diesel Injector Apparatus |
ASTM D 4175 : 2000 : EDT 1 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
ASTM D 4175 : 2016 : REV A | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
ASTM D 4294 : 2008 : REV A : EDT 1 | Standard Test Method for Sulfur in Petroleum and Petroleum Products by Energy Dispersive X-ray Fluorescence Spectrometry |
ASTM D 4052 : 1996 | Standard Test Method for Density and Relative Density of Liquids by Digital Density Meter |
ASTM D 4294 : 1998 | Standard Test Method for Sulfur in Petroleum Products by Energy-Dispersive X-Ray Fluorescence Spectroscopy |
ASTM D 2622 : 2010 | Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry |
ASTM D 2709 : 1988 | Standard Test Method for Water and Sediment in Distillate Fuels by Centrifuge |
ASTM D 4485 : 2005 | Standard Specification for Performance of Engine Oils |
ASTM D 5185 : 2009 | Standard Test Method for Determination of Additive Elements, Wear Metals, and Contaminants in Used Lubricating Oils and Determination of Selected Elements in Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES) |
ASTM D 4737 : 1996 : REV A | Standard Test Method for Calculated Cetane Index by Four Variable Equation |
ASTM D 7422 : 2009 : REV A | Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine |
ASTM D 4485 : 2014 | Standard Specification for Performance of Active API Service Category Engine Oils |
ASTM D 5453 : 2019 : REV A | Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence |
ASTM D 4485 : 2002 | Standard Specification for Performance of Engine Oils |
ASTM D 2622 : 2007 | Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry |
ASTM D 4175 : 2017 : REV A | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
ASTM D 2274 : 2003 : REV A | Standard Test Method for Oxidation Stability of Distillate Fuel Oil (Accelerated Method) |
ASTM D 4485 : 2005 : EDT 1 | Standard Specification for Performance of Engine Oils |
ASTM D 2622 : 1994 | Standard Test Method for Sulfur in Petroleum Products by X-Ray Spectrometry |
ASTM D 4175 : 2009 : REV A : EDT 2 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
ASTM D 2622 : 2005 | Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry |
ASTM D 5185 : 2002 : EDT 1 | Standard Test Method for Determination of Additive Elements, Wear Metals, and Contaminants in Used Lubricating Oils and Determination of Selected Elements in Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES) |
ASTM D 4294 : 2003 | Standard Test Method for Sulfur in Petroleum and Petroleum Products by Energy-Dispersive X-Ray Fluorescence Spectrometry |
ASTM D 4737 : 2004 | Standard Test Method for Calculated Cetane Index by Four Variable Equation |
ASTM D 5453 : 2019 | Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence |
ASTM D 4175 : 2018 : EDT 1 | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
ASTM D 4175 : 2016 | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
ASTM D 1319 : 2015 | Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption |
ASTM D 7422 : 2017 | Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine |
ASTM D 4294 : 2016 | Standard Test Method for Sulfur in Petroleum and Petroleum Products by Energy Dispersive X-ray Fluorescence Spectrometry |
ASTM D 5185 : 2002 : EDT 2 | Standard Test Method for Determination of Additive Elements, Wear Metals, and Contaminants in Used Lubricating Oils and Determination of Selected Elements in Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES) |
ASTM D 1319 : 2013 | Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption |
ASTM D 4052 : 2015 | Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter |
ASTM D 6278 : 2002 | Standard Test Method for Shear Stability of Polymer Containing Fluids Using a European Diesel Injector Apparatus |
ASTM D 4175 : 2017 | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
ASTM D 6278 : 2007 | Standard Test Method for Shear Stability of Polymer Containing Fluids Using a European Diesel Injector Apparatus |
ASTM D 4175 : 2019 | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
ASTM D 2274 : 2001 : REV A | Standard Test Method for Oxidation Stability of Distillate Fuel Oil (Accelerated Method) |
ASTM D 4485 : 2009 | Standard Specification for Performance of Engine Oils |
ASTM D 2274 : 2014 | Standard Test Method for Oxidation Stability of Distillate Fuel Oil (Accelerated Method) |
ASTM D 4175 : 2015 : REV B : EDT 1 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
ASTM D 4485 : 2010 : REV A | Standard Specification for Performance of Engine Oils |
ASTM D 5453 : 2003 : REV A | Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Motor Fuels and Oils by Ultraviolet Fluorescence |
ASTM D 4485 : 2011 | Standard Specification for Performance of Engine Oils |
ASTM D 1319 : 2019 | Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption |
ASTM D 4052 : 2018 | Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter |
ASTM D 4737 : 2010 | Standard Test Method for Calculated Cetane Index by Four Variable Equation |
ASTM D 4294 : 1990 : R1998 : EDT 1 | Standard Test Method for Sulfur in Petroleum Products by Energy-Dispersive X-Ray Fluorescence Spectroscopy |
ASTM D 1319 : 2002 | Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption |
ASTM D 4175 : 2008 : REV B | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
ASTM D 2622 : 2016 | Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry |
ASTM D 2709 : 1996 : R2001 : EDT 1 | Standard Test Method for Water and Sediment in Middle Distillate Fuels by Centrifuge |
ASTM D 7422 : 2014 | Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine |
ASTM D 5453 : 2008 | Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence |
ASTM D 4485 : 2007 : REV A | Standard Specification for Performance of Engine Oils |
ASTM D 5453 : 2000 : EDT 1 | Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Motor Fuels and Oils by Ultraviolet Fluorescence |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.