ASTM D 5893/D5893M : 2016 : R2021
Current
The latest, up-to-date edition.
Standard Specification for Cold-Applied, Single-Component, Chemically Curing Silicone Joint Sealant for Portland Cement Concrete Pavements
Hardcopy , PDF
English
05-10-2021
Important note : All end users must be registered with an Account prior to user licenses being assigned.| Committee |
D 04
|
| DocumentType |
Standard
|
| Pages |
6
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Current
|
| Supersedes |
1.1This specification covers cold-applied, single-component, chemically curing silicone sealants that are based on polymers of polysiloxane structures and are intended for use in sealing joints and cracks in portland cement concrete highway and airfield pavements. The specification includes both non-sag and self-leveling types of sealants.
1.1.1This specification does not purport to cover the properties required of sealants for use in areas of portland cement concrete pavements subject to jet fuel or other fuel spillage, such as vehicle or aircraft refueling and maintenance areas, or a combination thereof.
1.2The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.
1.3The following safety hazards caveat pertains only to the test methods portion, Section 9, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in Appendix X1.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM E 2785 : 2014 | Standard Test Method for Exposure of Firestop Materials to Severe Environmental Conditions |
| ASTM C 792 : 2023 | Standard Test Method for Effects of Heat Aging on Weight Loss, Cracking, and Chalking of Elastomeric Sealants |
| ASTM C 661 : 2015 : R2022 | Standard Test Method for Indentation Hardness of Elastomeric-Type Sealants by Means of a Durometer |
| ASTM C 661 : 2015 | Standard Test Method for Indentation Hardness of Elastomeric-Type Sealants by Means of a Durometer |
| ASTM D 1985 : 2013 : R2024 | Standard Practice for Preparing Concrete Blocks for Testing Sealants, for Joints and Cracks |
| ASTM D 412 : 2016 : EDT 1 | Standard Test Methods for Vulcanized Rubber and Thermoplastic Elastomers—Tension |
| ASTM D 1985 : 2013 : R2019 | Standard Practice for Preparing Concrete Blocks for Testing Sealants, for Joints and Cracks |
| ASTM C 1183/C1183M : 2013 : R2018 | Standard Test Method for Extrusion Rate of Elastomeric Sealants |
| ASTM D 2202 : 2000 : R2023 | Standard Test Method for Slump of Sealants |
| ASTM D 618 : 2013 | Standard Practice for Conditioning Plastics for Testing |
| ASTM C 679 : 2015 : R2022 | Standard Test Method for Tack-Free Time of Elastomeric Sealants |
| ASTM C 792 : 2015 : R2020 | Standard Test Method for Effects of Heat Aging on Weight Loss, Cracking, and Chalking of Elastomeric Sealants |
| ASTM C 793 : 2023 | Standard Test Method for Effects of Laboratory Accelerated Weathering on Elastomeric Joint Sealants |
| ASTM D 412 : 2016 : R2021 | Standard Test Methods for Vulcanized Rubber and Thermoplastic Elastomers—Tension |
| ASTM C 679 : 2015 | Standard Test Method for Tack-Free Time of Elastomeric Sealants |
| ASTM C 793 : 2005 : R2017 | Standard Test Method for Effects of Laboratory Accelerated Weathering on Elastomeric Joint Sealants |
| ASTM C 1183/C1183M : 2013 : R2024 | Standard Test Method for Extrusion Rate of Elastomeric Sealants |
| ASTM D 2202 : 2000 : R2019 | Standard Test Method for Slump of Sealants |
| ASTM D 618 : 2021 | Standard Practice for Conditioning Plastics for Testing |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.