ASTM D 5531 : 2017
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Guide for Preparation, Maintenance, and Distribution of Physical Product Standards for Color and Geometric Appearance of Coatings
Available format(s)
Hardcopy , PDF
Superseded date
08-18-2023
Superseded by
Language(s)
English
Published date
07-28-2017
Important note : All end users must be registered with an Account prior to user licenses being assigned.This guide covers three levels of physical product standards for color or appearance, or both, commonly used in the coatings industry, provides terminology to describe each level, and describes techniques for generating and caring for standards.
| Committee |
D 01
|
| DocumentType |
Guide
|
| Pages |
4
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This guide covers three levels of physical product standards for color or appearance, or both, commonly used in the coatings industry, provides terminology to describe each level, and describes techniques for generating and caring for standards.
1.2The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM D 3794 : 2018 | Standard Guide for Testing Coil Coatings |
| ASTM D 3794 : 2022 | Standard Guide for Testing Coil Coatings |
| ASTM D 7195 : 2021 | Standard Guide for Setting Object Color Specifications |
| ASTM D 3451 : 2006 : R2017 | Standard Guide for Testing Coating Powders and Powder Coatings |
| ASTM D 1729 : 2016 | Standard Practice for Visual Appraisal of Colors and Color Differences of Diffusely-Illuminated Opaque Materials |
| ASTM D 7195 : 2016 : REV A | Standard Guide for Setting Object Color Specifications |
| ASTM D 3134 : 2015 | Standard Practice for Establishing Color and Gloss Tolerances |
| ASTM D 4086 : 1992 : REV A : R2007 | Standard Practice for Visual Evaluation of Metamerism |
| ASTM E 805 : 2022 | Standard Practice for Identification of Instrumental Methods of Color or Color-Difference Measurement of Materials |
| ASTM E 1331 : 1996 | Standard Test Method for Reflectance Factor and Color by Spectrophotometry Using Hemispherical Geometry |
| ASTM D 2244 : 2021 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
| ASTM E 1331 : 2015 | Standard Test Method for Reflectance Factor and Color by Spectrophotometry Using Hemispherical Geometry |
| ASTM E 1347 : 2006 : R2020 | Standard Test Method for Color and Color-Difference Measurement by Tristimulus Colorimetry |
| ASTM D 4086 : 1992 : REV A : R2012 | Standard Practice for Visual Evaluation of Metamerism |
| ASTM D 2244 : 2015 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
| ASTM E 1164 : 2007 | Standard Practice for Obtaining Spectrometric Data for Object-Color Evaluation |
| ASTM D 2244 : 2023 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
| ASTM D 2244 : 2011 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
| ASTM D 1729 : 2016 | Standard Practice for Visual Appraisal of Colors and Color Differences of Diffusely-Illuminated Opaque Materials |
| ASTM E 1345 : 1998 : R2008 | Standard Practice for Reducing the Effect of Variability of Color Measurement by Use of Multiple Measurements |
| ASTM D 2244 : 2009 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
| ASTM E 1347 : 2006 : R2015 | Standard Test Method for Color and Color-Difference Measurement by Tristimulus Colorimetry |
| ASTM D 3134 : 2015 | Standard Practice for Establishing Color and Gloss Tolerances |
| ASTM E 1164 : 2009 | Standard Practice for Obtaining Spectrometric Data for Object-Color Evaluation |
| ASTM D 2244 : 2002 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
| ASTM D 2244 : 2016 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
| ASTM E 284 : 2022 | Standard Terminology of Appearance |
| ASTM E 1347 : 2003 | Standard Test Method for Color and Color-Difference Measurement by Tristimulus (Filter) Colorimetry |
| ASTM D 2244 : 2015 : EDT 1 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
| ASTM D 2244 : 2009 : REV B | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
| ASTM D 2244 : 2002 : EDT 1 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
| ASTM D 2244 : 2015 : REV A | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
| ASTM E 1347 : 1997 | Standard Test Method for Color and Color-Difference Measurement by Tristimulus (Filter) Colorimetry |
| ASTM D 1729 : 1996 : R2009 | Standard Practice for Visual Appraisal of Colors and Color Differences of Diffusely-Illuminated Opaque Materials |
| ASTM D 4449 : 1990 : R1999 | Standard Test Method for Visual Evaluation of Gloss Differences Between Surfaces of Similar Appearance |
| ASTM E 1349 : 2006 : R2013 | Standard Test Method for Reflectance Factor and Color by Spectrophotometry Using Bidirectional (45°:0° or 0°:45°) Geometry |
| ASTM E 1345 : 1998 : R2014 | Standard Practice for Reducing the Effect of Variability of Color Measurement by Use of Multiple Measurements |
| ASTM D 2244 : 2014 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
| ASTM E 1347 : 2006 | Standard Test Method for Color and Color-Difference Measurement by Tristimulus Colorimetry |
| ASTM D 1729 : 1996 : R2003 | Standard Practice for Visual Appraisal of Colors and Color Differences of Diffusely-Illuminated Opaque Materials |
| ASTM D 2244 : 2005 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
| ASTM E 1331 : 2004 | Standard Test Method for Reflectance Factor and Color by Spectrophotometry Using Hemispherical Geometry |
| ASTM E 1164 : 2012 : EDT 1 | Standard Practice for Obtaining Spectrometric Data for Object-Color Evaluation |
| ASTM E 1164 : 1994 | Standard Practice for Obtaining Spectrophotometric Data for Object-Color Evaluation |
| ASTM E 805 : 2012 : REV A : R2017 | Standard Practice for Identification of Instrumental Methods of Color or Color-Difference Measurement of Materials |
| ASTM E 1164 : 2012 : R2023 : EDT 1 | Standard Practice for Obtaining Spectrometric Data for Object-Color Evaluation |
| ASTM E 1345 : 1998 : R2019 | Standard Practice for Reducing the Effect of Variability of Color Measurement by Use of Multiple Measurements |
| ASTM E 1349 : 1990 : R1998 | Standard Test Method for Reflectance Factor and Color by Spectrophotometry Using Bidirectional Geometry |
| ASTM E 1349 : 2006 | Standard Test Method for Reflectance Factor and Color by Spectrophotometry Using Bidirectional (45:0 or 0:45) Geometry |
| ASTM D 3134 : 2015 : R2019 | Standard Practice for Establishing Color and Gloss Tolerances |
| ASTM D 4086 : 1992 : REV A : R2003 | Standard Practice for Visual Evaluation of Metamerism |
| ASTM D 2244 : 2007 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
| ASTM E 308 : 2018 | Standard Practice for Computing the Colors of Objects by Using the CIE System |
| ASTM D 823 : 2018 | Standard Practices for Producing Films of Uniform Thickness of Paint, Coatings and Related Products on Test Panels |
| ASTM D 3134 : 1997 : R2003 | Standard Practice for Establishing Color and Gloss Tolerances |
| ASTM D 2244 : 2022 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
| ASTM E 1347 : 2006 : R2011 | Standard Test Method for Color and Color-Difference Measurement by Tristimulus Colorimetry |
| ASTM D 1729 : 1996 | Standard Practice for Visual Appraisal of Colors and Color Differences of Diffusely-Illuminated Opaque Materials |
| ASTM D 3134 : 1997 | Standard Practice for Establishing Color and Gloss Tolerances |
| ASTM D 4449 : 2015 | Standard Test Method for Visual Evaluation of Gloss Differences Between Surfaces of Similar Appearance |
| ASTM D 4449 : 2015 : R2021 | Standard Test Method for Visual Evaluation of Gloss Differences Between Surfaces of Similar Appearance |
| ASTM E 1164 : 2002 | Standard Practice for Obtaining Spectrometric Data for Object-Color Evaluation |
| ASTM E 1331 : 2009 | Standard Test Method for Reflectance Factor and Color by Spectrophotometry Using Hemispherical Geometry |
| ASTM E 1164 : 2012 | Standard Practice for Obtaining Spectrometric Data for Object-Color Evaluation |
| ASTM D 3134 : 1997 : R2008 : EDT 1 | Standard Practice for Establishing Color and Gloss Tolerances |
| ASTM D 1729 : 2022 | Standard Practice for Visual Appraisal of Colors and Color Differences of Diffusely-Illuminated Opaque Materials |
| ASTM E 1345 : 1998 | Standard Practice for Reducing the Effect of Variability of Color Measurement by Use of Multiple Measurements |
| ASTM E 1331 : 2015 : R2019 | Standard Test Method for Reflectance Factor and Color by Spectrophotometry Using Hemispherical Geometry |
| ASTM E 1349 : 2006 : R2022 | Standard Test Method for Reflectance Factor and Color by Spectrophotometry Using Bidirectional (45°:0° or 0°:45°) Geometry |
| ASTM D 4086 : 1992 : REV A : R1997 : EDT 1 | Standard Practice for Visual Evaluation of Metamerism |
| ASTM E 308 : 2022 | Standard Practice for Computing the Colors of Objects by Using the CIE System |
| ASTM D 2244 : 2009 : REV A | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
| ASTM D 4449 : 2008 | Standard Test Method for Visual Evaluation of Gloss Differences Between Surfaces of Similar Appearance |
| ASTM D 2244 : 1993 : R2000 | Standard Test Method for Calculation of Color Differences From Instrumentally Measured Color Coordinates |
| ASTM E 1345 : 1998 : R2008 : EDT 1 | Standard Practice for Reducing the Effect of Variability of Color Measurement by Use of Multiple Measurements |
| ASTM D 823 : 2018 : R2022 | Standard Practices for Producing Films of Uniform Thickness of Paint, Coatings and Related Products on Test Panels |
| ASTM E 1349 : 2006 : R2018 | Standard Test Method for Reflectance Factor and Color by Spectrophotometry Using Bidirectional (45°:0° or 0°:45°) Geometry |
| ASTM E 1164 : 2012 : R2017 : EDT 1 | Standard Practice for Obtaining Spectrometric Data for Object-Color Evaluation |
| ASTM E 284 : 2017 | Standard Terminology of Appearance |
| ASTM D 4086 : 2018 | Standard Practice for Visual Evaluation of Metamerism |
| ASTM E 1345 : 1998 : R2003 | Standard Practice for Reducing the Effect of Variability of Color Measurement by Use of Multiple Measurements |
| ASTM D 4449 : 1990 : R2004 | Standard Test Method for Visual Evaluation of Gloss Differences Between Surfaces of Similar Appearance |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.