ASTM D 5397 : 2019
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Evaluation of Stress Crack Resistance of Polyolefin Geomembranes Using Notched Constant Tensile Load Test
Hardcopy , PDF
04-24-2020
English
01-01-2019
Important note : All end users must be registered with an Account prior to user licenses being assigned.This test method is used to develop test data from which the susceptibility of polyolefin geomembrane sheet material to stress cracking under a constant tensile load condition and an accelerated environmental condition can be evaluated.
| Committee |
D 35
|
| DocumentType |
Test Method
|
| Pages |
7
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This test method is used to develop test data from which the susceptibility of polyolefin geomembrane sheet material to stress cracking under a constant tensile load condition and an accelerated environmental condition can be evaluated.
1.2This test method measures the failure time associated with a given test specimen at a specified tensile load level. Results from a series of such tests utilizing a range of load levels can be used to construct a stress-time plot on a log-log axis.
1.3The values stated in SI units are to be regarded as the standard. The inch-pound units given in parentheses are provided for information only.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM D 5819 : 2018 | Standard Guide for Selecting Test Methods for Experimental Evaluation of Geosynthetic Durability |
| ASTM F 3181 : 2016 | Standard Test Method for The Un-notched, Constant Ligament Stress Crack Test (UCLS) for HDPE Materials Containing Post- Consumer Recycled HDPE |
| ASTM F 2136 : 2018 | Standard Test Method for Notched, Constant Ligament-Stress (NCLS) Test to Determine Slow-Crack-Growth Resistance of HDPE Resins or HDPE Corrugated Pipe |
| ASTM D 5747/D5747M : 2008 : R2013 : EDT 1 | Standard Practice for Tests to Evaluate the Chemical Resistance of Geomembranes to Liquids |
| ASTM D 4703 : 2002 | Standard Practice for Compression Molding Thermoplastic Materials into Test Specimens, Plaques, or Sheets |
| ASTM D 4439 : 2015 | Standard Terminology for Geosynthetics |
| ASTM D 4354 : 2012 | Standard Practice for Sampling of Geosynthetics and Rolled Erosion Control Products(RECPs) for Testing |
| ASTM D 5199 : 2012 : R2019 | Standard Test Method for Measuring the Nominal Thickness of Geosynthetics |
| ASTM D 4703 : 2003 | Standard Practice for Compression Molding Thermoplastic Materials into Test Specimens, Plaques, or Sheets |
| ASTM D 4703 : 1993 | Standard Practice for Compression Molding Thermoplastic Materials into Test Specimens, Plaques, or Sheets |
| ASTM D 4439 : 2011 | Standard Terminology for Geosynthetics |
| ASTM D 5199 : 2001 | Standard Test Method for Measuring the Nominal Thickness of Geosynthetics |
| ASTM D 4439 : 2015 : REV A | Standard Terminology for Geosynthetics |
| ASTM D 4439 : 2002 | Standard Terminology for Geosynthetics |
| ASTM D 4703 : 2010 | Standard Practice for Compression Molding Thermoplastic Materials into Test Specimens, Plaques, or Sheets |
| ASTM D 4439 : 2017 | Standard Terminology for Geosynthetics |
| ASTM D 4439 : 2001 | Standard Terminology for Geosynthetics |
| ASTM D 4439 : 2014 | Standard Terminology for Geosynthetics |
| ASTM D 4354 : 1999 : R2009 | Standard Practice for Sampling of Geosynthetics for Testing |
| ASTM D 5199 : 2012 | Standard Test Method for Measuring the Nominal Thickness of Geosynthetics |
| ASTM D 5199 : 2011 | Standard Test Method for Measuring the Nominal Thickness of Geosynthetics |
| ASTM D 4354 : 1999 | Standard Practice for Sampling of Geosynthetics for Testing |
| ASTM D 4439 : 2004 | Standard Terminology for Geosynthetics |
| ASTM D 4703 : 2000 | Standard Practice for Compression Molding Thermoplastic Materials into Test Specimens, Plaques, or Sheets |
| ASTM D 4703 : 2010 : REV A | Standard Practice for Compression Molding Thermoplastic Materials into Test Specimens, Plaques, or Sheets |
| ASTM D 4703 : 2016 | Standard Practice for Compression Molding Thermoplastic Materials into Test Specimens, Plaques, or Sheets |
| ASTM D 5199 : 2001 : R2006 | Standard Test Method for Measuring the Nominal Thickness of Geosynthetics |
| ASTM D 4439 : 2000 | Standard Terminology for Geosynthetics |
| ASTM D 4354 : 1999 : R2004 | Standard Practice for Sampling of Geosynthetics for Testing |
| ASTM D 4703 : 2007 | Standard Practice for Compression Molding Thermoplastic Materials into Test Specimens, Plaques, or Sheets |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.