ASTM D 4742 : 2017
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Oxidation Stability of Gasoline Automotive Engine Oils by Thin-Film Oxygen Uptake (TFOUT)
Hardcopy , PDF
09-29-2023
English
07-17-2017
Important note : All end users must be registered with an Account prior to user licenses being assigned.| Committee |
D 02
|
| DocumentType |
Test Method
|
| Pages |
11
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This test method evaluates the oxidation stability of engine oils for gasoline automotive engines. This test, run at 160 °C, utilizes a high pressure reactor pressurized with oxygen along with a metal catalyst package, a fuel catalyst, and water in a partial simulation of the conditions to which an oil may be subjected in a gasoline combustion engine. This test method can be used for engine oils with viscosity in the range from 4 mm2/s (cSt) to 21 mm2/s (cSt) at 100 °C, including re-refined oils.
1.2This test method is not a substitute for the engine testing of an engine oil in established engine tests, such as Sequence IIID.
1.3The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.3.1Exception—Pressure units are provided in psig, and dimensions are provided in inches in Annex A1, because these are the industry accepted standard and the apparatus is built according to the figures shown.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific warning statements, see Sections 7 and 8.
1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM D 7098 : 2021 | Standard Test Method for Oxidation Stability of Lubricants by Thin-Film Oxygen Uptake (TFOUT) Catalyst B |
| ASTM D 2272 : 2014 : REV A | Standard Test Method for Oxidation Stability of Steam Turbine Oils by Rotating Pressure Vessel |
| ASTM D 7098 : 2008 : R2015 | Standard Test Method for Oxidation Stability of Lubricants by Thin-Film Oxygen Uptake (TFOUT) Catalyst B |
| ASTM D 4057 : 2019 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
| ASTM D 4057 : 1995 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
| ASTM D 664 : 2017 : REV A | Standard Test Method for Acid Number of Petroleum Products by Potentiometric Titration |
| ASTM D 4057 : 2012 : R2018 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
| ASTM D 1193 : 1977 : R1983 : EDT 1 | Standard Specification for Reagent Water |
| ASTM B 211 : 1999 | Standard Specification for Aluminum and Aluminum-Alloy Bar, Rod, and Wire |
| ASTM D 4057 : 1981 : EDT 2 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
| ASTM A 314 : 1997 | Standard Specification for Stainless Steel Billets and Bars for Forging |
| ASTM D 4057 : 2006 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
| ASTM D 1193 : 2006 : R2011 | Standard Specification for Reagent Water |
| ASTM D 4057 : 2012 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
| ASTM D 664 : 1995 | Standard Test Method for Acid Number of Petroleum Products by Potentiometric Titration |
| ASTM D 2272 : 1998 | Standard Test Method for Oxidation Stability of Steam Turbine Oils by Rotating Pressure Vessel |
| ASTM D 1193 : 1991 | Standard Specification for Reagent Water |
| ASTM D 2272 : 2014 : REV A | Standard Test Method for Oxidation Stability of Steam Turbine Oils by Rotating Pressure Vessel |
| ASTM D 2272 : 2009 | Standard Test Method for Oxidation Stability of Steam Turbine Oils by Rotating Pressure Vessel |
| ASTM D 2272 : 2014 | Standard Test Method for Oxidation Stability of Steam Turbine Oils by Rotating Pressure Vessel |
| ASTM D 664 : 2011 : REV A | Standard Test Method for Acid Number of Petroleum Products by Potentiometric Titration |
| ASTM E 1 : 2014 : R2020 | Standard Specification for ASTM Liquid-in-Glass Thermometers |
| ASTM D 2272 : 2022 | Standard Test Method for Oxidation Stability of Steam Turbine Oils by Rotating Pressure Vessel |
| ASTM D 4057 : 2022 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
| ASTM D 2272 : 2002 | Standard Test Method for Oxidation Stability of Steam Turbine Oils by Rotating Pressure Vessel |
| ASTM D 1193 : 1970 | Standard Specification For Reagent Water |
| ASTM D 1193 : 2006 | Standard Specification for Reagent Water |
| ASTM D 1193 : 1999 | Standard Specification for Reagent Water |
| ASTM D 4057 : 1995 : R2000 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
| ASTM D 2272 : 2011 | Standard Test Method for Oxidation Stability of Steam Turbine Oils by Rotating Pressure Vessel |
| ASTM D 1193 : 2006 : R2018 | Standard Specification for Reagent Water |
| ASTM D 4057 : 2006 : R2011 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.