ASTM D 4289 : 2019
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Elastomer Compatibility of Lubricating Greases and Fluids
Hardcopy , PDF
08-10-2024
English
12-10-2019
Important note : All end users must be registered with an Account prior to user licenses being assigned.| Committee |
D 02
|
| DocumentType |
Test Method
|
| Pages |
8
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This test method evaluates the compatibility of lubricating greases and fluids with coupons cut from standard elastomer sheets (Practice D3182) or, optionally, from SAE Specification AMS 3217/2C (NBR-L) and AMS 3217/3B (CR) sheets. Compatibility is evaluated by determining the changes in volume and Durometer A hardness that occur when elastomer coupons are totally immersed in a lubricant sample for 70 h at either 100 °C or 150 °C or as required by the lubricant specification.
1.1.1Some lubricant specifications may require different test conditions, such as longer durations or lower or higher temperatures. In such instances, the repeatability and reproducibility values stated in Section 12 do not apply, and the user and supplier should agree on acceptable limits of precision.
Note 1:The scope of this test method now includes the evaluation of the elastomer compatibility of both lubricating fluids and greases. Testing of fluids was not included in Test Method D4289–95 and earlier versions.
1.2This test method can also be used as a guide to evaluate the compatibility of greases with rubber products not in standard sheet form (Practice D3183).
1.3The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.3.1Exception—When listed, Durometer A units shall be regarded as the standard.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific warning statements, see 8.4 – 8.6.
1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM D 8112 : 2017 | Standard Guide for Obtaining In-Service Samples of Turbine Operation Related Lubricating Fluid |
| ASTM F 2489 : 2006 : R2013 | Standard Guide for Instrument and Precision Bearing Lubricants—Part 2 Greases |
| ASTM D 4950 : 2019 | Standard Classification and Specification for Automotive Service Greases |
| ASTM D 8324 : 2021 | Standard Guide for Selection of Environmentally Acceptable Lubricants for the U.S. Environmental Protection Agency (EPA) Vessel General Permit |
| ASTM D 4175 : 2020 | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 471 : 2016 : REV A | Standard Test Method for Rubber Property—Effect of Liquids |
| ASTM D 217 : 2021 | Standard Test Methods for Cone Penetration of Lubricating Grease |
| ASTM D 4175 : 2020 : REV B | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 4175 : 2020 : REV A | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 217 : 2021 : REV A | Standard Test Methods for Cone Penetration of Lubricating Grease |
| ASTM D 4175 : 2001 : EDT 1 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 4175 : 2020 : REV B : EDT 1 | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 412 : 2016 : EDT 1 | Standard Test Methods for Vulcanized Rubber and Thermoplastic Elastomers—Tension |
| ASTM D 3183 : 2010 : R2015 | Standard Practice for Rubber—Preparation of Pieces for Test Purposes from Products |
| ASTM D 4175 : 2002 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 217 : 2019 : REV B | Standard Test Methods for Cone Penetration of Lubricating Grease |
| ASTM D 471 : 2016 : REV A : R2021 | Standard Test Method for Rubber Property—Effect of Liquids |
| ASTM D 412 : 2016 | Standard Test Methods for Vulcanized Rubber and Thermoplastic Elastomers—Tension |
| ASTM D 217 : 1997 | Standard Test Methods for Cone Penetration of Lubricating Grease |
| ASTM D 2240 : 2015 : R2021 | Standard Test Method for Rubber Property—Durometer Hardness |
| ASTM D 3183 : 1984 : R1998 | Standard Practice for Rubber-Preparation of Pieces for Test Purposes from Products |
| ASTM D 4175 : 2019 : EDT 1 | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 297 : 2015 : R2019 | Standard Test Methods for Rubber Products—Chemical Analysis |
| ASTM D 3182 : 1989 : R2001 | Standard Practice for Rubber—Materials, Equipment, and Procedures for Mixing Standard Compounds and Preparing Standard Vulcanized Sheets |
| ASTM D 2240 : 2015 : EDT 1 | Standard Test Method for Rubber Property—Durometer Hardness |
| ASTM D 412 : 2016 : R2021 | Standard Test Methods for Vulcanized Rubber and Thermoplastic Elastomers—Tension |
| ASTM D 3182 : 2021 | Standard Practice for Rubber—Materials, Equipment, and Procedures for Mixing Standard Compounds and Preparing Standard Vulcanized Sheets |
| ASTM D 3182 : 2016 | Standard Practice for Rubber—Materials, Equipment, and Procedures for Mixing Standard Compounds and Preparing Standard Vulcanized Sheets |
| ASTM D 297 : 2021 | Standard Test Methods for Rubber Products—Chemical Analysis |
| ASTM D 3182 : 2021 : REV A | Standard Practice for Rubber—Materials, Equipment, and Procedures for Mixing Standard Compounds and Preparing Standard Vulcanized Sheets |
| ASTM D 3183 : 2010 : R2019 | Standard Practice for Rubber—Preparation of Pieces for Test Purposes from Products |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.