ASTM D 4067 : 2016
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Classification System and Basis for Specification for Reinforced and Filled Poly(Phenylene Sulfide) (PPS) Injection Molding and Extrusion Materials Using ASTM Methods
Available format(s)
Hardcopy , PDF
Superseded date
01-05-2022
Superseded by
Language(s)
English
Published date
09-07-2016
Important note : All end users must be registered with an Account prior to user licenses being assigned.| Committee |
D 20
|
| DocumentType |
Standard
|
| Pages |
5
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This classification system covers reinforced and filled poly(phenylene sulfide) materials suitable for injection molding and extrusion.
1.2This classification system is not intended for the selection of materials, but only as a means to call out plastic materials to be used for the manufacture of parts. The selection of these materials shall be made by personnel with expertise in the plastics field where the environment, inherent properties of the materials, performance of the parts, part design, manufacturing process, and economics are considered.
1.3The properties included in this classification system are those required to identify the compositions covered. If necessary, other requirements identifying particular characteristics important to specific applications shall be designated by using the suffixes given in Section 5 or Classification System D4000.
1.4The values stated in SI units are to be regarded as the standard.
1.5This precautionary statement pertains only to the test method portion of this classification system, Section 12. This standard does not purport to address all of the safety concerns associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Note 1:There is no known ISO equivalent to this standard.
| ASTM D 4000 : 2016 | Standard Classification System for Specifying Plastic Materials |
| AWWA C702 : 2019 | COLD-WATER METERS - COMPOUND TYPE |
| ASTM D 4000 : 2020 | Standard Classification System for Specifying Plastic Materials |
| ASTM D 1600 : 1999 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM E 662 : 2021 | Standard Test Method for Specific Optical Density of Smoke Generated by Solid Materials |
| ASTM D 1238 : 2000 | Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer |
| ASTM D 1238 : 2004 : REV C | Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer |
| ASTM D 3418 : 2012 : EDT 1 | Standard Test Method for Transition Temperatures and Enthalpies of Fusion and Crystallization of Polymers by Differential Scanning Calorimetry |
| ASTM D 4000 : 2013 | Standard Classification System for Specifying Plastic Materials |
| ASTM D 3418 : 1982 : R1988 : EDT 1 | Standard Test Method for Transition Temperatures of Polymers By Thermal Analysis |
| ASTM D 3892 : 2015 : R2020 | Standard Practice for Packaging/Packing of Plastics |
| ASTM D 3418 : 1999 | Standard Test Method for Transition Temperatures of Polymers By Differential Scanning Calorimetry |
| ASTM D 1238 : 2013 | Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer |
| ASTM D 4000 : 2003 : REV A | Standard Classification System for Specifying Plastic Materials |
| ASTM D 3418 : 2021 | Standard Test Method for Transition Temperatures and Enthalpies of Fusion and Crystallization of Polymers by Differential Scanning Calorimetry |
| ASTM D 4000 : 2000 : REV A | Standard Classification System for Specifying Plastic Materials |
| ASTM D 5740 : 2003 | Standard Guide for Writing Material Standards in the Classification D4000 Format |
| ASTM D 4000 : 2012 | Standard Classification System for Specifying Plastic Materials |
| ASTM D 4000 : 2009 | Standard Classification System for Specifying Plastic Materials |
| ASTM D 3641 : 2002 | Standard Practice for Injection Molding Test Specimens of Thermoplastic Molding and Extrusion Materials |
| ASTM D 1238 : 2010 | Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer |
| ASTM E 595 : 2015 | Standard Test Method for Total Mass Loss and Collected Volatile Condensable Materials from Outgassing in a Vacuum Environment |
| ASTM E 29 : 2002 | Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications |
| ASTM E 662 : 2021 : REV A | Standard Test Method for Specific Optical Density of Smoke Generated by Solid Materials |
| ASTM D 3892 : 1993 : R2003 | Standard Practice for Packaging/Packing of Plastics |
| ASTM D 3892 : 2015 | Standard Practice for Packaging/Packing of Plastics |
| ASTM D 4000 : 2011 | Standard Classification System for Specifying Plastic Materials |
| ASTM D 3892 : 1993 : R1998 | Standard Practice for Packaging/Packing of Plastics |
| ASTM D 5740 : 1997 | Standard Guide for Writing Material Standards in the Classification D4000 Format |
| ASTM E 662 : 2019 | Standard Test Method for Specific Optical Density of Smoke Generated by Solid Materials |
| ASTM D 1600 : 2007 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 4000 : 2004 : EDT 1 | Standard Classification System for Specifying Plastic Materials |
| ASTM D 1600 : 2013 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 3641 : 2021 | Standard Practice for Injection Molding Test Specimens of Thermoplastic Molding and Extrusion Materials |
| ASTM D 3418 : 2012 | Standard Test Method for Transition Temperatures and Enthalpies of Fusion and Crystallization of Polymers by Differential Scanning Calorimetry |
| ASTM D 3641 : 2010 | Standard Practice for Injection Molding Test Specimens of Thermoplastic Molding and Extrusion Materials |
| ASTM D 1600 : 2014 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 3418 : 2003 | Standard Test Method for Transition Temperatures and Enthalpies of Fusion and Crystallization of Polymers by Differential Scanning Calorimetry |
| ASTM D 5740 : 2016 | Standard Guide for Writing Material Standards in the Classification <astmref design="D4000"/> Format |
| ASTM D 1600 : 2008 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 3418 : 2015 | Standard Test Method for Transition Temperatures and Enthalpies of Fusion and Crystallization of Polymers by Differential Scanning Calorimetry |
| ASTM D 4000 : 2009 : REV B | Standard Classification System for Specifying Plastic Materials |
| ASTM D 5740 : 2011 | Standard Guide for Writing Material Standards in the Classification D4000 Format |
| ASTM D 3641 : 2015 | Standard Practice for Injection Molding Test Specimens of Thermoplastic Molding and Extrusion Materials |
| ASTM D 4000 : 2000 | Standard Classification System for Specifying Plastic Materials |
| ASTM D 3641 : 2010 : REV A | Standard Practice for Injection Molding Test Specimens of Thermoplastic Molding and Extrusion Materials |
| ASTM D 4000 : 2010 : REV A | Standard Classification System for Specifying Plastic Materials |
| ASTM D 3641 : 2014 | Standard Practice for Injection Molding Test Specimens of Thermoplastic Molding and Extrusion Materials |
| ASTM D 4000 : 2007 | Standard Classification System for Specifying Plastic Materials |
| ASTM E 595 : 2015 : R2021 | Standard Test Method for Total Mass Loss and Collected Volatile Condensable Materials from Outgassing in a Vacuum Environment |
| ASTM D 4000 : 2009 : REV A | Standard Classification System for Specifying Plastic Materials |
| ASTM D 5630 : 2013 | Standard Test Method for Ash Content in Plastics (Withdrawn 2022) |
| ASTM D 4000 : 2001 | Standard Classification System for Specifying Plastic Materials |
| ASTM D 5630 : 1994 | Standard Test Method for Ash Content in Thermoplastics |
| ASTM D 3835 : 1996 | Standard Test Method for Determination of Properties of Polymeric Materials by Means of a Capillary Rheometer |
| ASTM D 4000 : 2008 | Standard Classification System for Specifying Plastic Materials |
| ASTM D 1238 : 2004 | Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer |
| ASTM D 3835 : 2016 | Standard Test Method for Determination of Properties of Polymeric Materials by Means of a Capillary Rheometer |
| ASTM D 1600 : 2018 | Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024) |
| ASTM D 618 : 2013 | Standard Practice for Conditioning Plastics for Testing |
| ASTM D 3418 : 2008 | Standard Test Method for Transition Temperatures and Enthalpies of Fusion and Crystallization of Polymers by Differential Scanning Calorimetry |
| ASTM D 4000 : 2001 : REV A : EDT 1 | Standard Classification System for Specifying Plastic Materials |
| ASTM D 4000 : 2004 | Standard Classification System for Specifying Plastic Materials |
| ASTM D 6358 : 2019 : EDT 1 | Standard Classification System and Basis for Specification for Poly (Phenylene Sulfide) (PPS) Injection Molding, Extrusion and Blow Molding Materials Using ISO Methods |
| ASTM D 3835 : 2008 | Standard Test Method for Determination of Properties of Polymeric Materials by Means of a Capillary Rheometer |
| ASTM D 6358 : 1999 | Standard Classification System for Poly (Phenylene Sulfide) Injection Molding and Extrusion Materials Using ISO Methods |
| ASTM D 5740 : 2009 | Standard Guide for Writing Material Standards in the Classification D4000 Format |
| ASTM D 5630 : 2001 | Standard Test Method for Ash Content in Thermoplastics |
| ASTM D 3835 : 1979 : R1983 | Standard Test Method for Rheological Properties of Thermoplastics with a Capillary Rheometer |
| ASTM D 3892 : 1993 : R2009 | Standard Practice for Packaging/Packing of Plastics |
| ASTM D 1238 : 2001 : EDT 1 | Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer |
| ASTM D 6358 : 2019 | Standard Classification System and Basis for Specification for Poly (Phenylene Sulfide) (PPS) Injection Molding, Extrusion and Blow Molding Materials Using ISO Methods |
| ASTM D 4000 : 2010 | Standard Classification System for Specifying Plastic Materials |
| ASTM D 6358 : 2011 | Standard Classification System and Basis for Specification for Poly (Phenylene Sulfide) (PPS) Injection Molding and Extrusion Materials Using ISO Methods |
| ASTM E 662 : 2021 : REV A : EDT 1 | Standard Test Method for Specific Optical Density of Smoke Generated by Solid Materials |
| ASTM D 5630 : 2006 | Standard Test Method for Ash Content in Plastics |
| ASTM D 3641 : 1997 | Standard Practice for Injection Molding Test Specimens of Thermoplastic Molding and Extrusion Materials |
| ASTM D 3835 : 2002 | Standard Test Method for Determination of Properties of Polymeric Materials by Means of a Capillary Rheometer |
| ASTM D 1238 : 2004 : REV A | Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer |
| ASTM D 6358 : 2006 | Standard Classification System for Poly (Phenylene Sulfide) Injection Molding and Extrusion Materials Using ISO Methods |
| ASTM D 3641 : 2012 | Standard Practice for Injection Molding Test Specimens of Thermoplastic Molding and Extrusion Materials |
| ASTM D 4000 : 2003 | Standard Classification System for Specifying Plastic Materials |
| ASTM D 1238 : 1985 | Standard Test Method for Flow Rates of Thermoplastics by Extrusion Plastometer |
| ASTM D 618 : 2021 | Standard Practice for Conditioning Plastics for Testing |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.