ASTM D 3895 : 2019
Current
Current
The latest, up-to-date edition.
Standard Test Method for Oxidative-Induction Time of Polyolefins by Differential Scanning Calorimetry
Available format(s)
Hardcopy , PDF
Language(s)
English
Published date
06-24-2019
Important note : All end users must be registered with an Account prior to user licenses being assigned.This test method outlines a procedure for the determination of oxidative-induction time (OIT) of polymeric materials by differential scanning calorimetry (DSC).
| Committee |
D 20
|
| DocumentType |
Test Method
|
| Pages |
7
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Current
|
| Supersedes |
1.1This test method outlines a procedure for the determination of oxidative-induction time (OIT) of polymeric materials by differential scanning calorimetry (DSC). It is applicable to polyolefin resins that are in a fully stabilized/compounded form.
1.2The values stated in SI units are to be regarded as the standard.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific hazards information is given in Section 8.
Note 1:This standard and ISO 11357–6 2013 address the same subject matter, but differ in technical content.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM D 5747/D5747M : 2008 : R2013 : EDT 1 | Standard Practice for Tests to Evaluate the Chemical Resistance of Geomembranes to Liquids |
| ASTM F 3346 : 2019 | Standard Specification for Polyethylene of Raised Temperature/Aluminum/Polyethylene of Raised Temperature (PERT/AL/PE-RT) Composite Pressure Pipe |
| ASTM D 4000 : 2016 | Standard Classification System for Specifying Plastic Materials |
| ASTM D 5885/D5885M : 2017 | Standard Test Method for Oxidative Induction Time of Polyolefin Geosynthetics by High-Pressure Differential Scanning Calorimetry |
| ASTM F 2788/F2788M : 2019 | Standard Specification for Metric and Inch-sized Crosslinked Polyethylene (PEX) Pipe |
| ASTM F 2623 : 2019 | Standard Specification for Polyethylene of Raised Temperature (PE-RT) Systems for Non-Potable Water Applications |
| ASTM E 2046 : 2014 | Standard Test Method for Reaction Induction Time by Thermal Analysis |
| ASTM F 3123 : 2018 : REV A | Standard Specification for Metric Outside Diameter Polyethylene (PE) Plastic Pipe (DR-PN) |
| ASTM D 4732 : 2013 | Standard Specification for Cool-Application Filling Compounds for Telecommunications Wire and Cable |
| ASTM F 2986 : 2012 : R2017 | Standard Specification for Corrugated Polyethylene Pipe and Fittings for Mine Leachate Applications |
| ASTM F 2389 : 2017 : REV A | Standard Specification for Pressure-rated Polypropylene (PP) Piping Systems |
| ASTM F 3219 : 2019 | Standard Specification for 3 to 30 in. (75 To 750 mm) Polypropylene (PP) Corrugated Single Wall Pipe and Fittings |
| ASTM D 4731 : 2013 | Standard Specification for Hot-Application Filling Compounds for Telecommunications Wire and Cable |
| ASTM D 6389 : 2017 | Standard Practice for Tests to Evaluate the Chemical Resistance of Geotextiles to Liquids |
| ASTM F 2769 : 2018 | Standard Specification for Polyethylene of Raised Temperature (PE-RT) Plastic Hot and Cold-Water Tubing and Distribution Systems |
| ASTM F 2881/F2881M : 2019 | Standard Specification for 12 to 60 in. [300 to 1500 mm] Polypropylene (PP) Dual Wall Pipe and Fittings for Non-Pressure Storm Sewer Applications |
| ASTM F 2306/F2306M : 2019 | Standard Specification for 12 to 60 in. [300 to 1500 mm] Annular Corrugated Profile-Wall Polyethylene (PE) Pipe and Fittings for Gravity-Flow Storm Sewer and Subsurface Drainage Applications |
| ASTM F 2764/F2764M : 2019 | Standard Specification for 6 to 60 in. [150 to 1500 mm] Polypropylene (PP) Corrugated Double and Triple Wall Pipe and Fittings for Non-Pressure Sanitary Sewer Applications |
| ASTM E 1858 : 2008 : R2015 : EDT 1 | Standard Test Methods for Determining Oxidation Induction Time of Hydrocarbons by Differential Scanning Calorimetry |
| ASTM E 2009 : 2008 : R2014 : EDT 1 | Standard Test Methods for Oxidation Onset Temperature of Hydrocarbons by Differential Scanning Calorimetry |
| ASTM F 2929 : 2017 | Standard Specification for Crosslinked Polyethylene (PEX) Tubing of 0.070 in. Wall and Fittings for Radiant Heating Systems up to 75 psig |
| ASTM F 3378/F3378M : 2022 | Standard Specification for Crosslinkable Polyethylene (CX-PE) Pipe |
| ASTM F 2788/F2788M : 2021 | Standard Specification for Metric and Inch-sized Crosslinked Polyethylene (PEX) Pipe |
| ASTM F 3506 : 2021 : EDT 1 | Standard Specification for Standard Specification for Polyethylene of Raised Temperature/Aluminum/Polyethylene of Raised Temperature (PE-RT/AL/PE-RT) Composite Pressure Pipe based on Inner Diameter (ID) for use in Air Conditioning and Refrigeration Line Set Systems |
| ASTM F 2306/F2306M : 2021 | Standard Specification for 300 mm to 1500 mm [12 in. to 60 in.] Annular Corrugated Profile-Wall Polyethylene (PE) Pipe and Fittings for Non-Pressure Gravity-Flow Storm Sewer and Subsurface Drainage Applications |
| ASTM D 4732 : 2013 : R2020 | Standard Specification for Cool-Application Filling Compounds for Telecommunications Wire and Cable |
| ASTM D 4731 : 2013 : R2020 | Standard Specification for Hot-Application Filling Compounds for Telecommunications Wire and Cable |
| ASTM D 8269 : 2021 | Standard Guide for the Use of Geocells in Geotechnical and Roadway Projects |
| ASTM F 2389 : 2023 | Standard Specification for Pressure-rated Polypropylene (PP) Piping Systems |
| ASTM D 5885/D5885M : 2020 | Standard Test Method for Oxidative Induction Time of Polyolefin Geosynthetics by High-Pressure Differential Scanning Calorimetry |
| ASTM F 2986 : 2012 : R2023 | Standard Specification for Corrugated Polyethylene Pipe and Fittings for Mine Leachate Applications |
| ASTM D 4000 : 2023 | Standard Classification System for Specifying Plastic Materials |
| ASTM F 2947/F2947M : 2021 : REV A | Standard Specification for 150 to 1500 mm [6 to 60 in.] Annular Corrugated Profile-Wall Polyethylene (PE) Pipe and Fittings for Sanitary Sewer Applications |
| ASTM E 2046 : 2019 | Standard Test Method for Reaction Induction Time by Thermal Analysis |
| ASTM D 5747/D5747M : 2021 | Standard Practice for Tests to Evaluate the Chemical Resistance of Geomembranes to Liquids |
| ASTM F 2881/F2881M : 2021 : EDT 1 | Standard Specification for 12 to 60 in. [300 to 1500 mm] Polypropylene (PP) Dual Wall Pipe and Fittings for Non-Pressure Storm Sewer Applications |
| ASTM D 6388 : 2018 | Standard Practice for Tests to Evaluate the Chemical Resistance of Geonets to Liquids |
| ASTM F 2929 : 2017 : R2021 | Standard Specification for Crosslinked Polyethylene (PEX) Tubing of 0.070 in. Wall and Fittings for Radiant Heating Systems up to 75 psig |
| ASTM F 2769 : 2023 : REV A | Standard Specification for Polyethylene of Raised Temperature (PE-RT) Plastic Hot and Cold-Water Tubing and Distribution Systems |
| ASTM F 3336 : 2022 | Standard Practice for Lipid Preconditioning of Ultra-High-Molecular-Weight Polyethylene for Accelerated Aging |
| ASTM E 2070 : 2013 : R2018 | Standard Test Methods for Kinetic Parameters by Differential Scanning Calorimetry Using Isothermal Methods |
| ASTM F 2720/F2720M : 2020 | Standard Specification for Glass Fiber Reinforced Polyethylene (PE-GF) Spiral Wound Large Diameter Pipe |
| ASTM F 3123 : 2022 | Standard Specification for Metric Outside Diameter Polyethylene (PE) Plastic Pipe (DR-PN) |
| ASTM E 2009 : 2023 | Standard Test Methods for Oxidation Onset Temperature of Hydrocarbons by Differential Scanning Calorimetry |
| ASTM F 876 : 2023 | Standard Specification for Crosslinked Polyethylene (PEX) Tubing |
| ASTM E 1858 : 2023 | Standard Test Methods for Determining Oxidation Induction Time of Hydrocarbons by Differential Scanning Calorimetry |
| ASTM F 2764/F2764M : 2023 | Standard Specification for 6 in. to 60 in. [150 mm to 1500 mm] Polypropylene (PP) Corrugated Double and Triple Wall Pipe and Fittings for Non-Pressure Sanitary Sewer Applications |
| ASTM F 2987 : 2012 : R2018 | Standard Specification for Corrugated Polyethylene Pipe and Fittings for Mine Heap Leach Aeration Applications (Withdrawn 2024) |
| ASTM E 1860 : 2023 | Standard Test Method for Elapsed Time Calibration of Thermal Analyzers |
| ASTM F 2623 : 2022 | Standard Specification for Polyethylene of Raised Temperature (PE-RT) Systems for Non-Potable Water Applications |
| ASTM E 473 : 2022 : REV D | Standard Terminology Relating to Thermal Analysis and Rheology |
| ASTM D 4703 : 2002 | Standard Practice for Compression Molding Thermoplastic Materials into Test Specimens, Plaques, or Sheets |
| ASTM E 473 : 2022 | Standard Terminology Relating to Thermal Analysis and Rheology |
| ASTM E 473 : 2021 | Standard Terminology Relating to Thermal Analysis and Rheology |
| ASTM D 4703 : 2003 | Standard Practice for Compression Molding Thermoplastic Materials into Test Specimens, Plaques, or Sheets |
| ASTM E 2935 : 2017 | Standard Practice for Conducting Equivalence Testing in Laboratory Applications |
| ASTM E 2935 : 2014 | Standard Practice for Conducting Equivalence Testing in Laboratory Applications |
| ASTM E 473 : 2022 : REV B | Standard Terminology Relating to Thermal Analysis and Rheology |
| ASTM E 473 : 2018 | Standard Terminology Relating to Thermal Analysis and Rheology |
| ASTM E 691 : 2020 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM E 2935 : 2013 | Standard Practice for Conducting Equivalence Testing in Laboratory Applications |
| ASTM D 4703 : 1993 | Standard Practice for Compression Molding Thermoplastic Materials into Test Specimens, Plaques, or Sheets |
| ASTM E 473 : 2023 : REV A | Standard Terminology Relating to Thermal Analysis and Rheology |
| ASTM E 691 : 2019 : EDT 1 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM E 473 : 2022 : REV C | Standard Terminology Relating to Thermal Analysis and Rheology |
| ASTM E 691 : 2023 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM D 4703 : 2010 | Standard Practice for Compression Molding Thermoplastic Materials into Test Specimens, Plaques, or Sheets |
| ASTM E 2935 : 2020 | Standard Practice for Conducting Equivalence Tests for Comparing Testing Processes |
| ASTM E 691 : 2022 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM E 691 : 2009 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM E 2935 : 2020 : EDT 1 | Standard Practice for Conducting Equivalence Tests for Comparing Testing Processes |
| ASTM E 691 : 2021 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
| ASTM E 2935 : 2016 | Standard Practice for Conducting Equivalence Testing in Laboratory Applications |
| ASTM E 473 : 2021 : REV A | Standard Terminology Relating to Thermal Analysis and Rheology |
| ASTM E 473 : 2023 : REV B | Standard Terminology Relating to Thermal Analysis and Rheology |
| ASTM D 4703 : 2000 | Standard Practice for Compression Molding Thermoplastic Materials into Test Specimens, Plaques, or Sheets |
| ASTM E 473 : 2022 : REV A | Standard Terminology Relating to Thermal Analysis and Rheology |
| ASTM E 2935 : 2021 | Standard Practice for Evaluating Equivalence of Two Testing Processes |
| ASTM E 473 : 2023 | Standard Terminology Relating to Thermal Analysis and Rheology |
| ASTM D 4703 : 2010 : REV A | Standard Practice for Compression Molding Thermoplastic Materials into Test Specimens, Plaques, or Sheets |
| ASTM D 4703 : 2016 | Standard Practice for Compression Molding Thermoplastic Materials into Test Specimens, Plaques, or Sheets |
| ASTM E 2935 : 2015 | Standard Practice for Conducting Equivalence Testing in Laboratory Applications |
| ASTM D 4703 : 2007 | Standard Practice for Compression Molding Thermoplastic Materials into Test Specimens, Plaques, or Sheets |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.