ASTM D 3744/D3744M : 2018
Current
The latest, up-to-date edition.
Standard Test Method for Aggregate Durability Index
Hardcopy , PDF
English
09-01-2018
1.1 This test method covers the determination of a durability index of an aggregate.
Committee |
D 04
|
DocumentType |
Test Method
|
Pages |
8
|
PublisherName |
American Society for Testing and Materials
|
Status |
Current
|
Supersedes |
1.1This test method covers the determination of a durability index of an aggregate. The calculated durability index is a value indicating the relative resistance of an aggregate to production of detrimental clay-like fines when subjected to the prescribed mechanical methods of degradation.
1.2Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.
1.2.1Measurements of volume and mass are only given in SI units because they are the only units typically used in practice when performing this test method.
1.2.2Measurements in Section 11, Section 15, Eq 3, Eq 4, and Table 1 are only given in inch-pound units because the equipment used in these sections is only manufactured using the inch-pound system.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM D 3666 : 2013 | Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials |
ASTM E 11 : 2020 | Standard Specification for Woven Wire Test Sieve Cloth and Test Sieves |
ASTM D 3666 : 2011 | Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials |
ASTM D 4753 : 2002 | Standard Guide for Evaluating, Selecting, and Specifying Balances and Standard Masses for Use in Soil, Rock, and Construction Materials Testing |
ASTM D 4753 : 2015 | Standard Guide for Evaluating, Selecting, and Specifying Balances and Standard Masses for Use in Soil, Rock, and Construction Materials Testing |
ASTM D 3666 : 2007 : REV A | Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials |
ASTM E 11 : 2024 | Standard Specification for Woven Wire Test Sieve Cloth and Test Sieves |
ASTM D 4753 : 2024 | Standard Guide for Evaluating, Selecting, and Specifying Balances and Standard Masses for Use in Soil, Rock, and Construction Materials Testing |
ASTM D 3666 : 2009 : REV A | Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials |
ASTM E 11 : 2022 | Standard Specification for Woven Wire Test Sieve Cloth and Test Sieves |
ASTM D 75/D75M : 2009 | Standard Practice for Sampling Aggregates |
ASTM D 4753 : 1995 | Standard Specification for Evaluating, Selecting, and Specifying Balances and Scales for Use in Soil, Rock, and Construction Materials Testing |
ASTM C 136/C136M : 2014 | Standard Test Method for Sieve Analysis of Fine and Coarse Aggregates |
ASTM D 3666 : 2005 | Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials |
ASTM D 3666 : 2003 : REV A | Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials |
ASTM D 3666 : 2000 | Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials |
ASTM D 3666 : 2007 | Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials |
ASTM D 75/D75M : 2014 | Standard Practice for Sampling Aggregates |
ASTM D 3666 : 2007 : EDT 2 | Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials |
ASTM D 4753 : 2007 | Standard Guide for Evaluating, Selecting, and Specifying Balances and Standard Masses for Use in Soil, Rock, and Construction Materials Testing |
ASTM D 2419 : 1995 | Standard Test Method for Sand Equivalent Value of Soils and Fine Aggregate |
ASTM D 3666 : 2016 | Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials |
ASTM D 2419 : 2009 | Standard Test Method for Sand Equivalent Value of Soils and Fine Aggregate |
ASTM D 3666 : 2003 | Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials |
ASTM D 3666 : 2001 | Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials |
ASTM D 3666 : 2024 | Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials |
ASTM D 3666 : 2006 | Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials |
ASTM C 127 : 2015 | Standard Test Method for Relative Density (Specific Gravity) and Absorption of Coarse Aggregate (Withdrawn 2024) |
ASTM D 3666 : 2004 | Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials |
ASTM C 127 : 2024 | Standard Test Method for Relative Density (Specific Gravity) and Absorption of Coarse Aggregate |
ASTM D 2419 : 2002 | Standard Test Method for Sand Equivalent Value of Soils and Fine Aggregate |
ASTM D 3666 : 2005 : REV A | Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials |
ASTM D 2419 : 2022 | Standard Test Method for Sand Equivalent Value of Soils and Fine Aggregate |
ASTM D 2419 : 2014 | Standard Test Method for Sand Equivalent Value of Soils and Fine Aggregate |
ASTM D 3666 : 2007 : REV A : EDT 1 | Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials |
ASTM D 3666 : 2009 | Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials |
ASTM D 3666 : 2002 | Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.