ASTM D 3606 : 1999
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Determination of Benzene and Toluene in Finished Motor and Aviation Gasoline by Gas Chromatography
Hardcopy , PDF
11-11-2014
English
04-10-1999
Important note : All end users must be registered with an Account prior to user licenses being assigned.| Committee |
D 02
|
| DocumentType |
Test Method
|
| Pages |
0
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1 This test method provides for the determination of benzene and toluene in finished motor and aviation gasolines by gas chromatography.
1.2 Benzene can be determined between the levels of 0.1 and 5 volume% and toluene can be determined between the levels of 2 and 20 volume%.
1.3 The precision for this test method was determined using conventional gasoline as well as gasolines containing oxygenates (ethers such as methyl tert-butyl ether, ethyl tert-butylether and tert-amylmethylether.
1.4 It has been determined that this test method is not applicable to gasolines containing ethanol. Methanol may also cause interference.
1.4 The values stated in SI units are to be regarded as the standard. Values given in parentheses are provided for information only.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Notes 1 through 11.
| ASTM D 5580 : 2015 | Standard Test Method for Determination of Benzene, Toluene, Ethylbenzene, <emph type="ital"> p/m</emph>-Xylene, <emph type="ital">o</emph>-Xylene, C<inf>9</inf> and Heavier Aromatics, and Total Aromatics in Finished Gasoline by Gas Chromatography |
| ASTM D 7235 : 2016 | Standard Guide for Establishing a Linear Correlation Relationship Between Analyzer and Primary Test Method Results Using Relevant ASTM Standard Practices |
| ASTM D 6300 : 2019 | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
| ASTM D 6733 : 2001 : R2016 | Standard Test Method for Determination of Individual Components in Spark Ignition Engine Fuels by 50-Metre Capillary High Resolution Gas Chromatography |
| ASTM D 5769 : 2015 | Standard Test Method for Determination of Benzene, Toluene, and Total Aromatics in Finished Gasolines by Gas Chromatography/Mass Spectrometry |
| ASTM D 7719 : 2018 | Standard Specification for High Aromatic Content Unleaded Hydrocarbon Aviation Gasoline |
| ASTM D 7165 : 2010 : R2015 | Standard Practice for Gas Chromatograph Based On-line/At-line Analysis for Sulfur Content of Gaseous Fuels |
| ASTM D 4815 : 2015 : REV B | Standard Test Method for Determination of MTBE, ETBE, TAME, DIPE, tertiary-Amyl Alcohol and C<inf>1</inf> to C<inf>4</inf> Alcohols in Gasoline by Gas Chromatography |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.