ASTM D 3588 : 1998 : R2017
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Practice for Calculating Heat Value, Compressibility Factor, and Relative Density of Gaseous Fuels
Hardcopy , PDF
06-06-2024
English
04-14-2017
CONTAINED IN VOL. 05.06, 2017 Defines procedures for calculating heating value, relative density, and compressibility factor at base conditions (14.696 psia and 60 degrees F (15.6 degrees C)) for natural gas mixtures from compositional analysis.
Committee |
D 03
|
DocumentType |
Standard Practice
|
Pages |
9
|
ProductNote |
Reconfirmed 2017
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
1.1This practice covers procedures for calculating heating value, relative density, and compressibility factor at base conditions (14.696 psia and 60°F (15.6°C)) for natural gas mixtures from compositional analysis.2 It applies to all common types of utility gaseous fuels, for example, dry natural gas, reformed gas, oil gas (both high and low Btu), propane-air, carbureted water gas, coke oven gas, and retort coal gas, for which suitable methods of analysis as described in Section 6 are available. Calculation procedures for other base conditions are given.
1.2The values stated in inch-pound units are to be regarded as the standard. The SI units given in parentheses are for information only.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM D 7314 : 2010 : R2015 | Standard Practice for Determination of the Heating Value of Gaseous Fuels using Calorimetry and On-line/At-line Sampling |
ASTM F 1496 : 2013 : R2019 | Standard Test Method for Performance of Convection Ovens |
ASTM F 2237 : 2003 : R2015 | Standard Test Method for Performance of Upright Overfired Broilers |
ASTM D 7940 : 2014 | Standard Practice for Analysis of Liquefied Natural Gas (LNG) by Fiber-Coupled Raman Spectroscopy |
ASTM F 1696 : 2018 | Standard Test Method for Energy Performance of Stationary-Rack, Door-Type Commercial Dishwashing Machines |
ASTM F 2239 : 2010 : R2016 | Standard Test Method for Performance of Conveyor Broilers |
ASTM F 2379 : 2004 : R2016 | Standard Test Method for Energy Performance of Powered Open Warewashing Sinks |
ASTM F 2238 : 2016 | Standard Test Method for Performance of Rapid Cook Ovens |
ASTM F 1920 : 2015 | Standard Test Method for Performance of Rack Conveyor Commercial Dishwashing Machines |
ASTM D 7164 : 2010 : R2015 | Standard Practice for On-line/At-line Heating Value Determination of Gaseous Fuels by Gas Chromatography |
ASTM F 1695 : 2003 : R2015 | Standard Test Method for Performance of Underfired Broilers |
ASTM F 1991 : 1999 : R2016 | Standard Test Method for Performance of Chinese (Wok) Ranges |
ASTM F 1361 : 2017 | Standard Test Method for Performance of Open Deep Fat Fryers |
ASTM F 3051 : 2014 : R2019 | Standard Test Method for Performance of Cook-and-Hold Ovens |
ASTM F 2473 : 2012 : R2018 | Standard Test Method for Performance of Water-Bath Rethermalizers |
ASTM F 1605 : 2014 : R2019 | Standard Test Method for Performance of Double-Sided Griddles |
ASTM F 2644 : 2007 : R2019 | Standard Test Method for Performance of Commercial Patio Heaters |
ASTM F 1484 : 2018 | Standard Test Methods for Performance of Steam Cookers |
ASTM F 2144 : 2017 | Standard Test Method for Performance of Large Open Vat Fryers |
ASTM D 7551 : 2010 : R2015 | Standard Test Method for Determination of Total Volatile Sulfur in Gaseous Hydrocarbons and Liquefied Petroleum Gases and Natural Gas by Ultraviolet Fluorescence (Withdrawn 2024) |
ASTM F 2861 : 2017 | Standard Test Method for Enhanced Performance of Combination Oven in Various Modes |
ASTM F 2022 : 2001 : R2019 | Standard Test Method for Performance of Booster Heaters |
ASTM D 7833 : 2014 | Standard Test Method for Determination of Hydrocarbons and Non-Hydrocarbon Gases in Gaseous Mixtures by Gas Chromatography |
ASTM F 3216 : 2016 | Standard Test Method for Performance of Retherm Ovens |
ASTM F 1275 : 2014 | Standard Test Method for Performance of Griddles |
ASTM D 4150 : 2019 | Standard Terminology Relating to Gaseous Fuels |
ASTM D 1946 : 1990 : R2015 : EDT 1 | Standard Practice for Analysis of Reformed Gas by Gas Chromatography |
GPA 2166 : 2005(R2017) | OBTAINING NATURAL GAS SAMPLES FOR ANALYSIS BY GAS CHROMATOGRAPHY |
ASTM D 2163 : 2014 : EDT 1 | Standard Test Method for Determination of Hydrocarbons in Liquefied Petroleum (LP) Gases and Propane/Propene Mixtures by Gas Chromatography |
ASTM D 2163 : 2007 | Standard Test Method for Determination of Hydrocarbons in Liquefied Petroleum (LP) Gases and Propane/Propene Mixtures by Gas Chromatography |
ASTM D 1945 : 1996 : EDT 1 | Standard Test Method for Analysis of Natural Gas by Gas Chromatography |
ASTM D 1945 : 1996 : R2001 | Standard Test Method for Analysis of Natural Gas by Gas Chromatography |
ASTM D 1946 : 1990 : R2006 | Standard Practice for Analysis of Reformed Gas by Gas Chromatography |
ASTM D 1946 : 1982 | Standard Method for Analysis of Reformed Gas by Gas Chromatography |
ASTM D 2650 : 2010 | Standard Test Method for Chemical Composition of Gases By Mass Spectrometry |
ASTM D 2650 : 2010 : R2015 | Standard Test Method for Chemical Composition of Gases by Mass Spectrometry |
GPA 2261 : 2013 | ANALYSIS FOR NATURAL GAS AND SIMILAR GASEOUS MIXTURES BY GAS CHROMATOGRAPHY |
GPA 2145 : 2016 | TABLE OF PHYSICAL PROPERTIES FOR HYDROCARBONS AND OTHER COMPOUNDS OF INTEREST TO NATURAL GAS AND NATURAL GAS LIQUIDS INDUSTRIES |
ASTM D 1946 : 1977 | Standard Method for Analysis Of Reformed Gas By Gas Chromatography |
ASTM D 2163 : 1991 : R1996 | Standard Test Method for Analysis of Liquefied Petroleum (LP) Gases and Propene Concentrates by Gas Chromatography (Withdrawn 2005) |
ASTM D 1945 : 2003 : R2010 | Standard Test Method for Analysis of Natural Gas by Gas Chromatography |
ASTM D 1945 : 2014 : R2019 | Standard Test Method for Analysis of Natural Gas by Gas Chromatography |
ASTM D 1946 : 1990 : R2000 | Standard Practice for Analysis of Reformed Gas by Gas Chromatography |
ASTM D 1945 : 2003 | Standard Test Method for Analysis of Natural Gas by Gas Chromatography |
ASTM D 1946 : 1990 : R2019 | Standard Practice for Analysis of Reformed Gas by Gas Chromatography |
ASTM D 2650 : 2004 | Standard Test Method for Chemical Composition of Gases By Mass Spectrometry |
ASTM D 1717 : 1961 : R1975 | Method of Test for Analysis of Commercial Butane-Butiene Mixtures and Isolutylene by Gas Chromatography (Withdrawn 1982) |
ASTM D 2163 : 2014 | Standard Test Method for Determination of Hydrocarbons in Liquefied Petroleum (LP) Gases and Propane/Propene Mixtures by Gas Chromatography |
ASTM D 2163 : 2014 : R2019 | Standard Test Method for Determination of Hydrocarbons in Liquefied Petroleum (LP) Gases and Propane/Propene Mixtures by Gas Chromatography |
ASTM D 1945 : 2014 | Standard Test Method for Analysis of Natural Gas by Gas Chromatography |
GPA 2172 : 2014 | CALCULATION OF GROSS HEATING VALUE, RELATIVE DENSITY, COMPRESSIBILITY AND THEORETICAL HYDROCARBON LIQUID CONTENT FOR NATURAL GAS MIXTURES FOR CUSTODY TRANSFER |
ASTM D 1946 : 1990 : R2011 | Standard Practice for Analysis of Reformed Gas by Gas Chromatography |
ASTM D 1945 : 2014 : REDLINE | Standard Test Method for Analysis of Natural Gas by Gas Chromatography |
ASTM D 1945 : 1991 | Standard Test Method for Analysis of Natural Gas by Gas Chromatography |
ASTM D 2650 : 1999 | Standard Test Method for Chemical Composition of Gases By Mass Spectrometry |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.