ASTM D 3567 : 1997
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Practice for Determining Dimensions of "Fiberglass" (Glass-Fiber-Reinforced Thermosetting Resin) Pipe and Fittings
Hardcopy , PDF
11-11-2014
English
11-10-1997
Important note : All end users must be registered with an Account prior to user licenses being assigned.| Committee |
D 20
|
| DocumentType |
Standard Practice
|
| Pages |
4
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy |
1.1 This practice covers the determination of outside diameter, inside diameter, total wall thickness, reinforced wall thickness, liner thickness (where applicable), and length dimensions of "fiberglass" (glass-fiber-reinforced thermosetting resin) pipe. Included are procedures for measuring tapered dimensions and taper angles for pipe intended to be joined by tapered socket fittings, and procedures for gaging internal and external threads.
1.2 This practice also includes procedures for determining dimensions for fiberglass pipe fittings.
1.3 The values stated in inch-pound units are to be regarded as the standard. The SI units given in parentheses are for information only.
1.4 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of whoever uses this standard to consult and establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| ASTM D 3840 : 2014 | Standard Specification for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe Fittings for Nonpressure Applications |
| ASTM F 2019 : 2011 | Standard Practice for Rehabilitation of Existing Pipelines and Conduits by the Pulled in Place Installation of Glass Reinforced Plastic (GRP) Cured-in-Place Thermosetting Resin Pipe (CIPP) |
| ASTM F 1417 : 2011 : REV A : R2015 | Standard Practice for Installation Acceptance of Plastic Non-pressure Sewer Lines Using Low-Pressure Air |
| ASTM D 1598 : 2015 : REV A | Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure |
| ASTM D 3754 : 2014 | Standard Specification for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Sewer and Industrial Pressure Pipe |
| ASTM D 5365 : 2018 | Standard Test Method for Long-Term Ring-Bending Strain of “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe |
| ASTM F 1173 : 2001 : R2018 | Standard Specification for Thermosetting Resin Fiberglass Pipe Systems to Be Used for Marine Applications |
| ASTM D 5685 : 2019 | Standard Specification for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pressure Pipe Fittings |
| ASTM D 2143 : 2015 | Standard Test Method for Cyclic Pressure Strength of Reinforced, Thermosetting Plastic Pipe |
| ASTM D 5813 : 2004 : R2018 | Standard Specification for Cured-In-Place Thermosetting Resin Sewer Piping Systems |
| ASTM D 2992 : 2018 | Standard Practice for Obtaining Hydrostatic or Pressure Design Basis for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe and Fittings |
| ASTM D 3517 : 2014 | Standard Specification for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pressure Pipe |
| ASTM D 3262 : 2016 | Standard Specification for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Sewer Pipe |
| ASTM D 2997 : 2015 | Standard Specification for Centrifugally Cast “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe |
| ASTM D 6041 : 2018 | Standard Specification for Contact-Molded “Fiberglass” (Glass-Fiber-Reinforced Thermosetting Resin) Corrosion Resistant Pipe and Fittings |
| ASTM F 1743 : 2017 | Standard Practice for Rehabilitation of Existing Pipelines and Conduits by Pulled-in-Place Installation of Cured-in-Place Thermosetting Resin Pipe (CIPP) |
| ASTM D 3681 : 2018 | Standard Test Method for Chemical Resistance of “Fiberglass” (Glass–Fiber–Reinforced Thermosetting-Resin) Pipe in a Deflected Condition |
| ASTM D 1599 : 2018 | Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings |
| ASTM D 2105 : 2001 : R2014 | Standard Test Method for Longitudinal Tensile Properties of “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe and Tube |
| ASTM F 1216 : 2016 | Standard Practice for Rehabilitation of Existing Pipelines and Conduits by the Inversion and Curing of a Resin-Impregnated Tube |
| ASTM D 2517 : 2018 | Standard Specification for Reinforced Epoxy Resin Gas Pressure Pipe and Fittings |
| ASTM D 6783 : 2005 : REV A : R2017 | Standard Specification for Polymer Concrete Pipe |
| ASTM D 5677 : 2017 | Standard Specification for Fiberglass (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe and Pipe Fittings, Adhesive Bonded Joint Type, for Aviation Jet Turbine Fuel Lines |
| ASTM D 2925 : 2014 | Standard Test Method for Beam Deflection of “Fiberglass” (Glass-Fiber-Reinforced Thermosetting Resin) Pipe Under Full Bore Flow |
| ASTM D 2996 : 2017 | Standard Specification for Filament-Wound “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.