ASTM D 3363 : 2020
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Film Hardness by Pencil Test
Hardcopy , PDF
07-18-2022
English
09-09-2020
Important note : All end users must be registered with an Account prior to user licenses being assigned.| Committee |
D 01
|
| DocumentType |
Test Method
|
| Pages |
3
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This test method covers a procedure for rapid, inexpensive determination of the film hardness of an organic coating on a substrate in terms of drawing leads or pencil leads of known hardness.
1.2This test method is similar in content (but not technically equivalent) to ISO 15184.
Note 1:Other procedures are available to measure permanent deformation of organic coatings under the action of a single point (stylus tip) including but not limited to Test Methods D2197, D5178, and G171.
1.3The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM D 4054 : 2022 | Standard Practice for Evaluation of New Aviation Turbine Fuels and Fuel Additives |
| ASTM D 3276 : 2021 | Standard Guide for Painting Inspectors (Metal Substrates) |
| ASTM D 7270 : 2007 : R2021 | Standard Guide for Environmental and Performance Verification of Factory-Applied Liquid Coatings |
| ASTM C 1729 : 2021 | Standard Specification for Aluminum Jacketing for Insulation |
| ASTM D 2454 : 2018 | Standard Practice for Determining the Effect of Overbaking on Organic Coatings |
| ASTM D 7187 : 2020 | Standard Test Method for Measuring Mechanistic Aspects of Scratch/Mar Behavior of Paint Coatings by Nanoscratching |
| ASTM F 1178 : 2011 : R2022 | Standard Specification for Performance of Enameling System, Baking, Metal Joiner Work and Furniture |
| ASTM D 5402 : 2019 | Standard Practice for Assessing the Solvent Resistance of Organic Coatings Using Solvent Rubs |
| ASTM A 755/A755M : 2018 | Standard Specification for Steel Sheet, Metallic Coated by the Hot-Dip Process and Prepainted by the Coil-Coating Process for Exterior Exposed Building Products |
| ASTM D 6943 : 2015 : R2019 | Standard Practice for Immersion Testing of Industrial Protective Coatings and Linings |
| ASTM C 1729M : 2021 | Standard Specification for Aluminum Jacketing for Insulation |
| ASTM C 1767M : 2021 | Standard Specification for Stainless Steel Jacketing for Insulation |
| ASTM D 1735 : 2021 | Standard Practice for Testing Water Resistance of Coatings Using Water Fog Apparatus |
| ASTM D 4585/D4585M : 2018 | Standard Practice for Testing Water Resistance of Coatings Using Controlled Condensation |
| ASTM C 1423 : 2021 | Standard Guide for Selecting Jacketing Materials for Thermal Insulation |
| ASTM D 870 : 2015 : R2020 | Standard Practice for Testing Water Resistance of Coatings Using Water Immersion |
| ASTM D 5498 : 2012 : REV A : R2018 | Standard Guide for Developing a Training Program for Personnel Performing Coating and Lining Work Inspection for Nuclear Facilities |
| ASTM D 3451 : 2006 : R2017 | Standard Guide for Testing Coating Powders and Powder Coatings |
| ASTM D 6577 : 2015 : R2019 | Standard Guide for Testing Industrial Protective Coatings |
| ASTM F 2831 : 2019 | Standard Practice for Internal Non Structural Epoxy Barrier Coating Material Used In Rehabilitation of Metallic Pressurized Piping Systems |
| ASTM D 2247 : 2015 : R2020 | Standard Practice for Testing Water Resistance of Coatings in 100 % Relative Humidity |
| ASTM C 1767 : 2021 | Standard Specification for Stainless Steel Jacketing for Insulation |
| ASTM D 3732 : 1982 : R2017 | Standard Practice for Reporting Cure Times of Ultraviolet-Cured Coatings |
| ASTM D 5178 : 2021 | Standard Test Method for Mar Resistance of Organic Coatings |
| ASTM D 2197 : 1998 | Standard Test Method for Adhesion of Organic Coatings by Scrape Adhesion |
| ASTM D 5178 : 1998 | Standard Test Method for Mar Resistance of Organic Coatings |
| ASTM D 5178 : 2016 | Standard Test Method for Mar Resistance of Organic Coatings |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.