ASTM D 3237 : 2017 : REDLINE
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Lead in Gasoline by Atomic Absorption Spectroscopy
11-05-2022
English
06-19-2017
CONTAINED IN VOL. 05.02, 2017 Specifies the determination of the total lead content of gasoline within the concentration range of 0.010 to 0.10 g of lead/U.S. gal (2.5 to 25 mg/L).
Committee |
D 02
|
DocumentType |
Redline
|
Pages |
4
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy |
1.1This test method covers the determination of the total lead content of gasoline within the concentration range of 0.010 g to 0.10 g of lead/U.S. gal (2.5 mg/L to 25 mg/L). This test method compensates for variations in gasoline composition and is independent of lead alkyl type.
1.2The values given in grams per U.S. gallon are to be regarded as the standard in the United States. Note that in other countries, other units can be preferred.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see 6.6 and 6.8.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
BS 7800:1992 | Specification for high octane (super) unleaded petrol (gasoline) for motor vehicles |
13/30279896 DC : 0 | BS ISO 8178-5 - RECIPROCATING INTERNAL COMBUSTION ENGINES - EXHAUST EMISSION MEASUREMENT - PART 5: TEST FUELS |
BS 7070:1985 | Specification for unleaded petrol (gasoline) for motor vehicles |
ASTM D 6201 : 2004 | Standard Test Method for Dynamometer Evaluation of Unleaded Spark-Ignition Engine Fuel for Intake Valve Deposit Formation |
ASTM D 6984 : 2017-05 | TEST METHOD FOR EVALUATION OF AUTOMOTIVE ENGINE OILS IN THE SEQUENCE IIIF, SPARK-IGNITION ENGINE |
BS ISO 8178-5:2008 | Reciprocating internal combustion engines. Exhaust emission measurement Test fuels |
ASTM D 8076 : 2017 : REV A | Standard Specification for 100 Research Octane Number Test Fuel for Automotive Spark-Ignition Engines |
ASTM D 7578 : 2015-06 | GUIDE FOR CALIBRATION REQUIREMENTS FOR ELEMENTAL ANALYSIS OF PETROLEUM PRODUCTS AND LUBRICANTS |
ASTM D 7320 : 2017-05 | TEST METHOD FOR EVALUATION OF AUTOMOTIVE ENGINE OILS IN THE SEQUENCE 3G, SPARK-IGNITION ENGINE |
ASTM D 7740 : 201 | Standard Practice for Optimization, Calibration, and Validation of Atomic Absorption Spectrometry for Metal Analysis of Petroleum Products and Lubricants |
ASTM D 8076 : 2017 | Standard Specification for 100 Research Octane Number Test Fuel for Automotive Spark-Ignition Engines |
ASTM D 3348 : 2012 | Standard Test Method for Rapid Field Test for Trace Lead in Unleaded Gasoline (Colorimetric Method) |
ASTM D 6201 : 2004 : R2009 | Standard Test Method for Dynamometer Evaluation of Unleaded Spark-Ignition Engine Fuel for Intake Valve Deposit Formation |
DEFSTAN 91-90/4(2015) : 2015 | GASOLINE AVIATION: GRADES UL91, 100/130 AND 100/130LL JOINT SERVICE DESIGNATION: AVGAS 100 AND AVGAS 100LL |
IES RP 27.3:2017 | Recommended Practice for Photobiological Safety for Lamps – Risk Group Classification and Labeling |
ASTM D 439 : 1989 | Specification for Automotive Gasoline (Withdrawn 1990) |
ASTM D 6837 : 2013 : REDLINE | Standard Test Method for Measurement of Effects of Automotive Engine Oils on Fuel Economy of Passenger Cars and Light-Duty Trucks in Sequence VIB Spark Ignition Engine<rangeref></rangeref > |
ASTM D 7589 : 2016 : REDLINE | Standard Test Method for Measurement of Effects of Automotive Engine Oils on Fuel Economy of Passenger Cars and Light-Duty Trucks in Sequence VID Spark Ignition Engine<rangeref></rangeref > |
ASTM D 6201 : 2004 : R2014 | Standard Test Method for Dynamometer Evaluation of Unleaded Spark-Ignition Engine Fuel for Intake Valve Deposit Formation |
I.S. EN ISO 8178-5:1998 | RECIPROCATING INTERNAL COMBUSTION ENGINES - EXHAUST EMISSION MEASUREMENT - PART 5: TEST FUELS |
BS 7070:1988 | Specification for unleaded petrol (gasoline) for motor vehicles |
MIL-STD-3004 Revision D:2014 | QUALITY ASSURANCE/SURVEILLANCE FOR FUELS, LUBRICANTS AND RELATED PRODUCTS |
ASTM D 7740 : 2011 : R2016 | Standard Practice for Optimization, Calibration, and Validation of Atomic Absorption Spectrometry for Metal Analysis of Petroleum Products and Lubricants |
ASTM D 2547 : 1982 | Method of Test for Lead in Gasoline, Columetric Chromate Method (Withdrawn 1989) |
ISO 8178-5:2015 | Reciprocating internal combustion engines Exhaust emission measurement Part 5: Test fuels |
EN ISO 8178-5 : 1997 | RECIPROCATING INTERNAL COMBUSTION ENGINES - EXHAUST EMISSION MEASUREMENT - TEST FUELS |
SAE J 1832 : 2016 | LOW PRESSURE GASOLINE FUEL INJECTOR |
ASTM D 8114 : 2017 | Standard Test Method for Measurement of Effects of Automotive Engine Oils on Fuel Economy of Passenger Cars and Light-Duty Trucks in Sequence VIE Spark Ignition |
ASTM D 8111 : 2017 | Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IIIH, Spark-Ignition Engine |
BS EN ISO 8178-5:1997 | Reciprocating internal combustion engines. Exhaust emission measurement Test fuels |
ASTM D 1949 : 1979 : R1984 : EDT 1 | Test Method for Separation of Tetraethyllead and Tetramethyllead in Gasoline |
ASTM D 6202 : 2002 | Standard Test Method for Automotive Engine Oils on the Fuel Economy of Passenger Cars and Light-Duty Trucks in the Sequence VIA Spark Ignition Engine (Withdrawn 2009) |
ASTM D 3348 : 2012 : R2017 | Standard Test Method for Rapid Field Test for Trace Lead in Unleaded Gasoline (Colorimetric Method) (Withdrawn 2022) |
ASTM D 6792 : 2017 : REDLINE | Standard Practice for Quality Management Systems in Petroleum Products, Liquid Fuels, and Lubricants Testing Laboratories |
ASTM D 2550 : 1985 : EDT 1 | Method of Test for Water Separation Characteristics of Aviation Turbine Fuels |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.