ASTM D 297 : 2015 : R2019
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Methods for Rubber Products—Chemical Analysis
Hardcopy , PDF
01-22-2022
English
12-24-2019
Important note : All end users must be registered with an Account prior to user licenses being assigned.| Committee |
D 11
|
| DocumentType |
Test Method
|
| Pages |
37
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1These test methods cover the qualitative and quantitative analysis of the composition of rubber products of the “R” family (see 3.1). Many of these test methods may be applied to the analysis of natural and synthetic crude rubbers.
1.1.1Part Aconsists of general test methods for use in the determination of some or all of the major constituents of a rubber product.
1.1.2Part Bcovers the determination of specific polymers present in a rubber product.
1.1.3The test methods appear in the following order:
| Part A. General Test Methods: | Sections |
| Rubber Polymer Content by the Indirect Method | 11 – 13 |
| Determinations and Report for the General Method | 14 and 15 |
| Density | 16 |
| Extract Analysis | 17 – 26 |
| Sulfur Analysis | 27.1 – 33 |
| Fillers Analysis | 34 – 40 |
| Ash Analysis | 41 – 51 |
| Part B. Determination of Rubber Polymers | 52 – 58 |
1.2The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific precautionary or warning statements are given in 31.4.5, 31.6, 37.4.2, 38.4.2, 45.1.3, 53.2.3.5, 54.4.2, 54.6, 56.5.3, and 57.7.3; and X1.3.3 and X2.4.1.6.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM D 6049 : 2003 : R2017 | Standard Test Method for Rubber Property—Measurement of the Viscous and Elastic Behavior of Unvulcanized Raw Rubbers and Rubber Compounds by Compression Between Parallel Plates |
| ASTM C 990M : 2009 : R2019 | Standard Specification for Joints for Concrete Pipe, Manholes, and Precast Box Sections Using Preformed Flexible Joint Sealants (Metric) (Withdrawn 2024) |
| ASTM D 6370 : 1999 : R2019 | Standard Test Method for Rubber—Compositional Analysis by Thermogravimetry (TGA) |
| ASTM D 5603 : 2019 : REV A | Standard Classification for Rubber Compounding Materials—Recycled Vulcanizate Rubber |
| ASTM E 524 : 2008 : R2020 | Standard Specification for Standard Smooth Tire for Pavement Skid-Resistance Tests |
| ASTM D 2765 : 2016 | Standard Test Methods for Determination of Gel Content and Swell Ratio of Crosslinked Ethylene Plastics |
| ASTM D 6576 : 2020 | Standard Specification for Flexible Cellular Rubber Chemically Blown |
| ASTM D 1049 : 1998 : R2017 | Standard Specification for Rubber Insulating Covers |
| ASTM D 3156 : 1996 : R2021 | Standard Practice for Rubber—Chromatographic Analysis of Antidegradants (Antioxidants, Antiozonants and Stabilizers) |
| ASTM E 1844 : 2008 : R2020 | Standard Specification for a Size 10 × 4–5 Smooth-Tread Friction Test Tire |
| ASTM F 2157 : 2009 : R2018 | Standard Specification for Synthetic Surfaced Running Tracks |
| ASTM D 5774 : 1995 : R2019 | Standard Test Methods for Rubber—Chemical Analysis of Extractables |
| ASTM D 8115 : 2017 : R2021 | Standard Test Method for Rubber Property—Abrasion Resistance (Multi-Directional Platform Abrader) |
| ASTM D 1051 : 2019 | Standard Specification for Rubber Insulating Sleeves |
| ASTM E 1551 : 2016 : R2020 | Standard Specification for a Size 4.00-8 Smooth Tread Friction Test Tire |
| ASTM D 3900 : 2017 : R2021 | Standard Test Methods for Rubber—Determination of Ethylene Units in Ethylene-Propylene Copolymers (EPM) and in Ethylene-Propylene-Diene Terpolymers (EPDM) by Infrared Spectrometry |
| ASTM D 4289 : 2019 | Standard Test Method for Elastomer Compatibility of Lubricating Greases and Fluids |
| ASTM D 8268 : 2019 | Standard Practice for Rubber Compounding Materials—Evaluation of Recycled Vulcanizate Particulate Rubber |
| ASTM D 7216 : 2020 : REV A | Standard Test Method for Determining Automotive Engine Oil Compatibility with Typical Seal Elastomers |
| ASTM D 1414 : 2015 | Standard Test Methods for Rubber O-Rings |
| ASTM D 7106/D7106M : 2005 : R2015 : EDT 1 | Standard Guide for Selection of Test Methods for Ethylene Propylene Diene Terpolymer (EPDM) Geomembranes |
| ASTM C 990 : 2009 : R2019 | Standard Specification for Joints for Concrete Pipe, Manholes, and Precast Box Sections Using Preformed Flexible Joint Sealants |
| ASTM D 1050 : 2005 : R2017 | Standard Specification for Rubber Insulating Line Hose |
| ASTM D 178 : 2019 | Standard Specification for Rubber Insulating Matting |
| ASTM D 5963 : 2004 : R2019 | Standard Test Method for Rubber Property—Abrasion Resistance (Rotary Drum Abrader) |
| ASTM D 1048 : 2020 | Standard Specification for Rubber Insulating Blankets |
| ASTM E 501 : 2008 : R2020 | Standard Specification for Standard Rib Tire for Pavement Skid-Resistance Tests |
| ASTM D 3452 : 2006 : R2021 | Standard Practice for Rubber—Identification by Pyrolysis-Gas Chromatography |
| ASTM D 6909 : 2010 : R2016 | Standard Specification for High Temperature and Acid-Resistant Fluorocarbon Terpolymer Elastomer |
| ASTM E 670 : 2009 : R2020 | Standard Test Method for Testing Side Force Friction on Paved Surfaces Using the Mu-Meter |
| ASTM D 1278 : 1991 : REV A : R2020 | Standard Test Methods for Rubber from Natural Sources—Chemical Analysis |
| ASTM D 6814 : 2002 : R2018 | Standard Test Method for Determination of Percent Devulcanization of Crumb Rubber Based on Crosslink Density |
| ASTM D 120 : 2021 | Standard Specification for Rubber Insulating Gloves |
| ASTM D 4483 : 2020 | Standard Practice for Evaluating Precision for Test Method Standards in the Rubber and Carbon Black Manufacturing Industries |
| ASTM D 1418 : 2017 | Standard Practice for Rubber and Rubber Latices—Nomenclature |
| ASTM D 3452 : 1993 : R1998 | Standard Practice for Rubber-Identification by Pyrolysis-Gas Chromatography |
| ASTM D 3156 : 1996 : R2016 | Standard Practice for Rubber—Chromatographic Analysis of Antidegradants (Antioxidants, Antiozonants and Stabilizers) |
| ASTM E 443 : 1991 | Test Method for Sulphur in Organic Compounds by Oxygen Flask Combustion (Withdrawn 1997) |
| ASTM D 1418 : 2021 : REV A | Standard Practice for Rubber and Rubber Latices—Nomenclature |
| ASTM D 1416 : 1989 | Test Methods for Rubber from Synthetic Sources--Chemical Analysis (Withdrawn 1996) |
| ASTM D 3452 : 2006 : R2017 | Standard Practice for Rubber—Identification by Pyrolysis-Gas Chromatography |
| ASTM D 4483 : 2018 | Standard Practice for Evaluating Precision for Test Method Standards in the Rubber and Carbon Black Manufacturing Industries |
| ASTM D 982 : 1965 | Method of Test for Organic Nitrogen in Paper and Paperboard |
| ASTM D 3156:1996 | Standard Practice for Rubber—Chromatographic Analysis of Antidegradants (Antioxidants, Antiozonants and Stabilizers) |
| ASTM E 442 : 1991 | Test Method for Chlorine, Bromine, or Iodine in Organic Compounds by Oxygen Flask Combustion (Withdrawn 1997) |
| ASTM D 3677 : 2010 : R2019 | Standard Test Methods for Rubber—Identification by Infrared Spectrophotometry |
| ASTM D 3452 : 2006 : R2021 | Standard Practice for Rubber—Identification by Pyrolysis-Gas Chromatography |
| ASTM D 3156 : 1996 : R2021 | Standard Practice for Rubber—Chromatographic Analysis of Antidegradants (Antioxidants, Antiozonants and Stabilizers) |
| ASTM D 1418 : 2021 | Standard Practice for Rubber and Rubber Latices—Nomenclature |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.