ASTM D 2915 : 1998 : EDT 1
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Practice for Evaluating Allowable Properties for Grades of Structural Lumber
Hardcopy , PDF
11-11-2014
English
10-10-1998
Important note : All end users must be registered with an Account prior to user licenses being assigned.| Committee |
D 07
|
| DocumentType |
Standard Practice
|
| Pages |
12
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy |
1.1 This practice covers sampling and analysis procedures for the investigation of specified populations of stress-graded structural lumber. Depending on the interest of the user, the population from which samples are taken may range from the lumber from a specific mill to all the lumber produced in a particular grade from a particular geographic area, during some specified interval of time. This practice generally assumes that the population is sufficiently large so that, for sampling purposes, it may be considered infinite. Where this assumption is inadequate, that is, the population is assumed finite, many of the provisions of this practice may be employed but the sampling and analysis procedure must be designed to reflect a finite population. The statistical techniques embodied in this practice provide procedures to summarize data so that logical judgments can be made. This practice does not specify the action to be taken after the results have been analyzed. The action to be taken depends on the particular requirements of the user of the product.
1.2 The values stated in inch-pound units are to be regarded as the standard.
1.3 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| ASTM D 1037 : 2012 | Standard Test Methods for Evaluating Properties of Wood-Base Fiber and Particle Panel Materials |
| ASTM D 7469 : 2016 | Standard Test Methods for End-Joints in Structural Wood Products |
| ASTM D 7258 : 2017 | Standard Specification for Polymeric Piles |
| ASTM D 5652 : 2015 | Standard Test Methods for Single-Bolt Connections in Wood and Wood-Based Products |
| ASTM D 7032 : 2017 | Standard Specification for Establishing Performance Ratings for Wood-Plastic Composite and Plastic Lumber Deck Boards, Stair Treads, Guards, and Handrails |
| ASTM D 7247 : 2017 | Standard Test Method for Evaluating the Shear Strength of Adhesive Bonds in Laminated Wood Products at Elevated Temperatures |
| ASTM D 7199 : 2007 : R2012 | Standard Practice for Establishing Characteristic Values for Reinforced Glued Laminated Timber (Glulam) Beams Using Mechanics-Based Models |
| ASTM D 5456 : 2019 | Standard Specification for Evaluation of Structural Composite Lumber Products |
| ASTM D 5764 : 1997 : REV A : R2018 | Standard Test Method for Evaluating Dowel-Bearing Strength of Wood and Wood-Based Products |
| ASTM D 3737 : 2018 : EDT 1 | Standard Practice for Establishing Allowable Properties for Structural Glued Laminated Timber (Glulam) |
| ASTM D 7672 : 2014 : EDT 1 | Standard Specification for Evaluating Structural Capacities of Rim Board Products and Assemblies |
| ASTM D 7031 : 2011 : R2019 | Standard Guide for Evaluating Mechanical and Physical Properties of Wood-Plastic Composite Products |
| ASTM D 4444 : 2013 : R2018 | Standard Test Method for Laboratory Standardization and Calibration of Hand-Held Moisture Meters |
| ASTM D 6570 : 2018 : REV A | Standard Practice for Assigning Allowable Properties for Mechanically Graded Lumber |
| ASTM D 5055 : 2019 | Standard Specification for Establishing and Monitoring Structural Capacities of Prefabricated Wood I-Joists |
| ASTM D 7438 : 2013 | Standard Practice for Field Calibration and Application of Hand-Held Moisture Meters |
| ASTM D 6662 : 2017 | Standard Specification for Polyolefin-Based Plastic Lumber Decking Boards |
| ASTM D 7857 : 2016 | Standard Test Method for Evaluating the Flexural Properties and Internal Bond Strength of Fire-Retarded Mat-Formed Wood Structural Composite Panels Exposed to Elevated Temperatures |
| ASTM D 6109 : 2019 | Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastic Lumber and Related Products |
| ASTM D 5457 : 2019 : REV B | Standard Specification for Computing Reference Resistance of Wood-Based Materials and Structural Connections for Load and Resistance Factor Design |
| ASTM D 2555 : 2017 : REV A | Standard Practice for Establishing Clear Wood Strength Values |
| ASTM D 7033 : 2014 | Standard Practice for Establishing Design Capacities for Oriented Strand Board (OSB) Wood-Based Structural-Use Panels |
| ASTM D 6815 : 2009 : R2015 | Standard Specification for Evaluation of Duration of Load and Creep Effects of Wood and Wood-Based Products |
| ASTM D 6555 : 2017 | Standard Guide for Evaluating System Effects in Repetitive-Member Wood Assemblies |
| ASTM E 2954 : 2015 | Standard Test Method for Axial Compression Test of Reinforced Plastic and Polymer Matrix Composite Vertical Members |
| ASTM D 7381 : 2007 : R2013 | Standard Practice for Establishing Allowable Stresses for Round Timbers for Piles from Tests of Full-Size Material |
| ASTM D 1990 : 2016 | Standard Practice for Establishing Allowable Properties for Visually-Graded Dimension Lumber from In-Grade Tests of Full-Size Specimens |
| ASTM D 7568 : 2017 | Standard Specification for Polyethylene-Based Structural-Grade Plastic Lumber for Outdoor Applications |
| ASTM D 198 : 2015 | Standard Test Methods of Static Tests of Lumber in Structural Sizes |
| ASTM D 6874 : 2012 | Standard Test Methods for Nondestructive Evaluation of Wood-Based Flexural Members Using Transverse Vibration |
| ASTM D 6782 : 2013 | Standard Test Methods for Standardization and Calibration of In-Line Dry Lumber Moisture Meters |
| ASTM D 5516 : 2018 | Standard Test Method for Evaluating the Flexural Properties of Fire-Retardant Treated Softwood Plywood Exposed to Elevated Temperatures |
| ASTM D 7341 : 2014 | Standard Practice for Establishing Characteristic Values for Flexural Properties of Structural Glued Laminated Timber by Full-Scale Testing |
| ASTM D 4761 : 2019 | Standard Test Methods for Mechanical Properties of Lumber and Wood-Based Structural Materials |
| ASTM D 5574 : 1994 : R2012 | Standard Test Methods for Establishing Allowable Mechanical Properties of Wood-Bonding Adhesives for Design of Structural Joints |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.