ASTM D 2887 : 2022 : EDT 1
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Boiling Range Distribution of Petroleum Fractions by Gas Chromatography
Hardcopy , PDF
12-11-2023
English
02-28-2023
Important note : All end users must be registered with an Account prior to user licenses being assigned.| Committee |
D 02
|
| DocumentType |
Test Method
|
| Pages |
34
|
| ProductNote |
ε1 NOTE—Editorially removed joint designation and corrected 13.1 in February 2023.
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This test method covers the determination of the boiling range distribution of petroleum products. The test method is applicable to petroleum products and fractions having a final boiling point of 538 °C (1000 °F) or lower at atmospheric pressure as measured by this test method. This test method is limited to samples having a boiling range greater than 55.5 °C (100 °F), and having a vapor pressure sufficiently low to permit sampling at ambient temperature.
Note 1:Since a boiling range is the difference between two temperatures, only the constant of 1.8 °F/°C is used in the conversion of the temperature range from one system of units to another.
1.1.1Procedure A (Sections 6 – 14)—Allows a larger selection of columns and analysis conditions such as packed and capillary columns as well as a Thermal Conductivity Detector in addition to the Flame Ionization Detector. Analysis times range from 14 min to 60 min.
1.1.2Procedure B (Sections 15 – 23)—Is restricted to only 3 capillary columns and requires no sample dilution. In addition, Procedure B is used not only for the sample types described in Procedure A but also for the analysis of samples containing biodiesel mixtures B5, B10, and B20. The analysis time, when using Procedure B (Accelerated D2887), is reduced to about 8 min.
1.2This test method is not to be used for the analysis of gasoline samples or gasoline components. These types of samples must be analyzed by Test Method D7096.
1.3The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM D 8147 : 2017 | Standard Specification for Special-Purpose Test Fuels for Aviation Compression-Ignition Engines |
| ASTM D 7213 : 2015 : R2019 | Standard Test Method for Boiling Range Distribution of Petroleum Distillates in the Boiling Range from 100 °C to 615 °C by Gas Chromatography |
| ASTM D 7807 : 2020 | Standard Test Method for Determination of Boiling Range Distribution of Hydrocarbon and Sulfur Components of Petroleum Distillates by Gas Chromatography and Chemiluminescence Detection |
| ASTM D 7798 : 2020 | Standard Test Method for Boiling Range Distribution of Petroleum Distillates with Final Boiling Points up to 538 °C by Ultra Fast Gas Chromatography (UF GC) |
| ASTM D 396 : 2021 | Standard Specification for Fuel Oils |
| ASTM D 975 : 2022 : REV A | Standard Specification for Diesel Fuel |
| ASTM D 4737 : 2021 | Standard Test Method for Calculated Cetane Index by Four Variable Equation |
| ASTM D 2226 : 1993 : R2022 | Standard Classification for Various Types of Petroleum Oils for Rubber Compounding Use |
| ASTM D 3699 : 2019 | Standard Specification for Kerosine |
| ASTM D 2549 : 2002 : R2017 | Standard Test Method for Separation of Representative Aromatics and Nonaromatics Fractions of High-Boiling Oils by Elution Chromatography |
| ASTM D 7215 : 2022 | Standard Test Method for Calculated Flash Point from Simulated Distillation Analysis of Distillate Fuels |
| ASTM D 6352 : 2019 : EDT 1 | Standard Test Method for Boiling Range Distribution of Petroleum Distillates in Boiling Range from 174 °C to 700 °C by Gas Chromatography |
| ASTM D 7223 : 2021 | Standard Specification for Aviation Certification Turbine Fuel |
| ASTM D 8046 : 2021 | Standard Guide for Pumpability of Heat Transfer Fluids |
| ASTM D 7566 : 2022 : REV A | Standard Specification for Aviation Turbine Fuel Containing Synthesized Hydrocarbons |
| ASTM D 5154/D5154M : 2018 | Standard Test Method for Determining Activity and Selectivity of Fluid Catalytic Cracking (FCC) Catalysts by Microactivity Test |
| ASTM D 7964/D7964M : 2019 | Standard Test Method for Determining Activity of Fluid Catalytic Cracking (FCC) Catalysts in a Fluidized Bed |
| ASTM D 6743 : 2020 | Standard Test Method for Thermal Stability of Organic Heat Transfer Fluids |
| ASTM D 4924 : 2021 | Standard Classification for Petroleum Waxes for Use in Rubber Compounding |
| ASTM D 7500 : 2015 : R2019 | Standard Test Method for Determination of Boiling Range Distribution of Distillates and Lubricating Base Oils—in Boiling Range from 100 °C to 735 °C by Gas Chromatography |
| ASTM D 7665 : 2022 | Standard Guide for Evaluation of Biodegradable Heat Transfer Fluids |
| ASTM D 7169 : 2020 : EDT 1 | Standard Test Method for Boiling Point Distribution of Samples with Residues Such as Crude Oils and Atmospheric and Vacuum Residues by High Temperature Gas Chromatography |
| ASTM D 4054 : 2022 | Standard Practice for Evaluation of New Aviation Turbine Fuels and Fuel Additives |
| ASTM D 6074 : 2015 : R2022 | Standard Guide for Characterizing Hydrocarbon Lubricant Base Oils |
| ASTM D 7863 : 2022 | Standard Guide for Evaluation of Convective Heat Transfer Coefficient of Liquids |
| ASTM D 6417 : 2015 : R2019 | Standard Test Method for Estimation of Engine Oil Volatility by Capillary Gas Chromatography |
| ASTM D 3338/D3338M : 2020 : REV A | Standard Test Method for Estimation of Net Heat of Combustion of Aviation Fuels |
| ASTM D 5372 : 2020 | Standard Guide for Evaluation of Hydrocarbon Heat Transfer Fluids |
| ASTM D 3343 : 2022 | Standard Test Method for Estimation of Hydrogen Content of Aviation Fuels |
| ASTM D 1655 : 2022 : REV A | Standard Specification for Aviation Turbine Fuels |
| ASTM D 3907/D3907M : 2019 | Standard Test Method for Testing Fluid Catalytic Cracking (FCC) Catalysts by Microactivity Test |
| ASTM D 5399 : 2009 : R2017 | Standard Test Method for Boiling Point Distribution of Hydrocarbon Solvents by Gas Chromatography |
| ASTM D 2892 : 2020 | Standard Test Method for Distillation of Crude Petroleum (15-Theoretical Plate Column) |
| ASTM D 7398 : 2021 | Standard Test Method for Boiling Range Distribution of Fatty Acid Methyl Esters (FAME) in the Boiling Range from 100 °C to 615 °C by Gas Chromatography |
| ASTM D 8144 : 2022 | Standard Test Method for Separation and Determination of Aromatics, Nonaromatics, and FAME Fractions in Middle Distillates by Solid-Phase Extraction and Gas Chromatography |
| ASTM D 975 : 2023 | Standard Specification for Diesel Fuel |
| ASTM D 976 : 2021 : EDT 1 | Standard Test Method for Calculated Cetane Index of Distillate Fuels |
| ASTM D 2880 : 2023 | Standard Specification for Gas Turbine Fuel Oils |
| ASTM D 7213 : 2023 | Standard Test Method for Boiling Range Distribution of Petroleum Distillates in the Boiling Range from 100 °C to 615 °C by Gas Chromatography |
| ASTM D 7169 : 2023 | Standard Test Method for Boiling Point Distribution of Samples with Residues Such as Crude Oils and Atmospheric and Vacuum Residues by High Temperature Gas Chromatography |
| ASTM D 7566 : 2023 : REV B | Standard Specification for Aviation Turbine Fuel Containing Synthesized Hydrocarbons |
| ASTM D 8519 : 2023 | Standard Test Method for Determination of Hydrocarbon Types in Waste Plastic Process Oil Using Gas Chromatography with Vacuum Ultraviolet Absorption Spectroscopy Detection (GC-VUV) |
| ASTM D 2549 : 2023 | Standard Test Method for Separation of Representative Aromatics and Nonaromatics Fractions of High-Boiling Oils by Elution Chromatography |
| ASTM D 7398 : 2023 | Standard Test Method for Boiling Range Distribution of Fatty Acid Methyl Esters (FAME) in the Boiling Range from 100 °C to 615 °C by Gas Chromatography |
| ASTM D 8147 : 2017 : R2023 | Standard Specification for Special-Purpose Test Fuels for Aviation Compression-Ignition Engines |
| ASTM D 4054 : 2023 | Standard Practice for Evaluation of New Aviation Turbine Fuels and Fuel Additives |
| ASTM D 2892 : 2023 | Standard Test Method for Distillation of Crude Petroleum (15-Theoretical Plate Column) |
| ASTM D 1655 : 2023 : REV A | Standard Specification for Aviation Turbine Fuels |
| ASTM D 5399 : 2009 : R2023 | Standard Test Method for Boiling Point Distribution of Hydrocarbon Solvents by Gas Chromatography |
| ASTM D 4057 : 2019 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
| ASTM D 86 : 2023 | Standard Test Method for Distillation of Petroleum Products and Liquid Fuels at Atmospheric Pressure |
| ASTM D 86 : 2020 : REV A | Standard Test Method for Distillation of Petroleum Products and Liquid Fuels at Atmospheric Pressure |
| ASTM D 86 : 2018 | Standard Test Method for Distillation of Petroleum Products and Liquid Fuels at Atmospheric Pressure |
| ASTM D 6299 : 2022 : EDT 1 | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
| ASTM D 86 : 2019 | Standard Test Method for Distillation of Petroleum Products and Liquid Fuels at Atmospheric Pressure |
| ASTM D 4175 : 2022 : REV A | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 6300 : 2021 | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 86 : 2012 | Standard Test Method for Distillation of Petroleum Products at Atmospheric Pressure |
| ASTM D 6300 : 2023 | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 2892 : 2020 | Standard Test Method for Distillation of Crude Petroleum (15-Theoretical Plate Column) |
| ASTM D 4175 : 2023 | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 6299 : 2023 : EDT 1 | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
| ASTM D 4175 : 2022 : REV A : EDT 1 | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 86 : 2020 : REV B | Standard Test Method for Distillation of Petroleum Products and Liquid Fuels at Atmospheric Pressure |
| ASTM D 86 : 2016 : REV A | Standard Test Method for Distillation of Petroleum Products and Liquid Fuels at Atmospheric Pressure |
| ASTM D 6299 : 2023 | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
| ASTM D 2892 : 2023 | Standard Test Method for Distillation of Crude Petroleum (15-Theoretical Plate Column) |
| ASTM D 4626 : 1995 : R2019 | Standard Practice for Calculation of Gas Chromatographic Response Factors |
| ASTM D 4175 : 2023 : EDT 1 | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 4626 : 2023 | Standard Practice for Calculation of Gas Chromatographic Response Factors |
| ASTM D 86 : 2020 | Standard Test Method for Distillation of Petroleum Products and Liquid Fuels at Atmospheric Pressure |
| ASTM D 86 : 2015 | Standard Test Method for Distillation of Petroleum Products and Liquid Fuels at Atmospheric Pressure |
| ASTM D 7169 : 2023 | Standard Test Method for Boiling Point Distribution of Samples with Residues Such as Crude Oils and Atmospheric and Vacuum Residues by High Temperature Gas Chromatography |
| ASTM D 86 : 2017 | Standard Test Method for Distillation of Petroleum Products and Liquid Fuels at Atmospheric Pressure |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.