ASTM D 2880 : 2018 : REV A
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Gas Turbine Fuel Oils
Hardcopy , PDF
05-12-2023
English
10-01-2018
| Committee |
D 02
|
| DocumentType |
Standard
|
| Pages |
8
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This specification covers the selection of fuels for gas turbines, excepting gas turbines used in aircraft, for the guidance of interested parties such as turbine manufacturers and the suppliers and purchasers of fuel oils. The specification sets forth the properties of fuels at the time and place of custody transfer to the user.
1.2Three appendixes are provided for informational purposes only and do not constitute a requirement of this specification unless mutually agreed upon between the interested parties.
1.2.1Appendix X1 describes the five grades of gas turbine fuels covered by this specification. Further, it states the significance of various test methods used in inspecting the fuels.
1.2.2Appendix X2 discusses the sources of fuel contaminants and notes the significance of such contaminants in the operation of gas turbines and gas turbine fuel systems. The particular significance of trace metals in gas turbine fuels is noted. Upper limits of trace metals are recommended for the various grades of gas turbine fuels, but these recommended limits do not constitute a requirement of the specification unless mutually agreed upon by the interested parties. Limitations due to the use of used or recycled oil are also noted.
Note 1:The gas turbine operator should consult Practice D4418 for methods of ensuring fuels of adequate cleanliness and for guidance on long-term storage of distillate fuels and on liquids from non-petroleum sources as gas turbine.
Note 2:Nothing in this specification shall preclude observance of federal, state, or local regulations which may be more restrictive.
Note 3:The generation and dissipation of static electricity can create problems in the handling of distillate gas turbine fuel oils. For more information on the subject, see Guide D4865.
1.3This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM D 4625 : 2016 : EDT 1 | Standard Test Method for Middle Distillate Fuel Storage Stability at 43 °C (110 °F) |
| ASTM D 7463 : 2018 | Standard Test Method for Adenosine Triphosphate (ATP) Content of Microorganisms in Fuel, Fuel/Water Mixtures, and Fuel Associated Water |
| ASTM D 6426 : 2018 | Standard Test Method for Determining Filterability of Middle Distillate Fuel Oils |
| ASTM D 7112 : 2019 | Standard Test Method for Determining Stability and Compatibility of Heavy Fuel Oils and Crude Oils by Heavy Fuel Oil Stability Analyzer (Optical Detection) |
| ASTM D 6468 : 2008 : R2019 | Standard Test Method for High Temperature Stability of Middle Distillate Fuels |
| ASTM D 7451 : 2019 | Standard Test Method for Water Separation Properties of Light and Middle Distillate, and Compression and Spark Ignition Fuels |
| ASTM D 7827 : 2019 | Standard Test Method for Measuring n-Heptane Induced Phase Separation of Asphaltene from Heavy Fuel Oils as Separability Number by an Optical Device |
| ASTM D 7060 : 2012 : R2019 | Standard Test Method for Determination of the Maximum Flocculation Ratio and Peptizing Power in Residual and Heavy Fuel Oils (Optical Detection Method) |
| ASTM D 7464 : 2019 | Standard Practice for Manual Sampling of Liquid Fuels, Associated Materials and Fuel System Components for Microbiological Testing |
| ASTM D 7061 : 2019 : EDT 1 | Standard Test Method for Measuring n-Heptane Induced Phase Separation of Asphaltene-Containing Heavy Fuel Oils as Separability Number by an Optical Scanning Device |
| ASTM D 975 : 2020 | Standard Specification for Diesel Fuel |
| ASTM D 2068 : 2017 | Standard Test Method for Determining Filter Blocking Tendency |
| ASTM D 2709 : 2016 | Standard Test Method for Water and Sediment in Middle Distillate Fuels by Centrifuge |
| ASTM D 3605 : 2017 | Standard Test Method for Trace Metals in Gas Turbine Fuels by Atomic Absorption and Flame Emission Spectroscopy |
| ASTM D 4418 : 2017 | Standard Practice for Receipt, Storage, and Handling of Fuels for Gas Turbines |
| ASTM D 4868 : 2017 | Standard Test Method for Estimation of Net and Gross Heat of Combustion of Hydrocarbon Burner and Diesel Fuels |
| ASTM D 6469 : 2017 | Standard Guide for Microbial Contamination in Fuels and Fuel Systems |
| ASTM D 6728 : 2016 | Standard Test Method for Determination of Contaminants in Gas Turbine and Diesel Engine Fuel by Rotating Disc Electrode Atomic Emission Spectrometry |
| ASTM D 6756 : 2017 | Standard Test Method for Determination of the Red Dye Concentration and Estimation of the ASTM Color of Diesel Fuel and Heating Oil Using a Portable Visible Spectrophotometer |
| ASTM D 7111 : 2016 | Standard Test Method for Determination of Trace Elements in Middle Distillate Fuels by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES) |
| ASTM D 7619 : 2017 | Standard Test Method for Sizing and Counting Particles in Light and Middle Distillate Fuels, by Automatic Particle Counter |
| ASTM D 7687 : 2017 | Standard Test Method for Measurement of Cellular Adenosine Triphosphate in Fuel and Fuel-associated Water With Sample Concentration by Filtration |
| ASTM D 8166 : 2017 | Standard Test Method for Sizing and Counting Particulates in Light and Middle Distillate Fuels and Biodiesel Blend (B6 to B20) Using Continuous Flow and Bottle Sampler Automatic Particle Counters |
| ASTM D 4865 : 2019 | Standard Guide for Generation and Dissipation of Static Electricity in Petroleum Fuel Systems |
| ASTM D 2622 : 1987 : EDT 1 | Standard Test Method for Sulfur in Petroleum Products by X-Ray Spectrometry |
| ASTM D 4865 : 2009 : R2014 | Standard Guide for Generation and Dissipation of Static Electricity in Petroleum Fuel Systems |
| ASTM D 5949 : 1996 | Standard Test Method for Pour Point of Petroleum Products (Automatic Pressure Pulsing Method) |
| ASTM D 5453 : 2000 | Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Motor Fuels and Oils by Ultraviolet Fluorescence |
| ASTM D 4052 : 2018 : REV A | Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter |
| ASTM D 3605 : 2000 | Standard Test Method for Trace Metals in Gas Turbine Fuels by Atomic Absorption and Flame Emission Spectroscopy |
| ASTM D 1552 : 2016 | Standard Test Method for Sulfur in Petroleum Products by High Temperature Combustion and Infrared (IR) Detection or Thermal Conducitivity Detection (TCD) |
| ASTM D 7346 : 2007 | Standard Test Method for No Flow Point of Petroleum Products |
| ASTM D 7094 : 2016 | Standard Test Method for Flash Point by Modified Continuously Closed Cup (MCCCFP) Tester |
| ASTM D 3605 : 2017 | Standard Test Method for Trace Metals in Gas Turbine Fuels by Atomic Absorption and Flame Emission Spectroscopy |
| ASTM D 1266 : 1987 | Standard Test Method for Sulfur in Petroleum Products (Lamp Method) |
| ASTM D 7344 : 2017 | Standard Test Method for Distillation of Petroleum Products and Liquid Fuels at Atmospheric Pressure (Mini Method) |
| ASTM D 6728 : 2001 | Standard Test Method for Determination of Contaminants in Gas Turbine and Diesel Engine Fuel by Rotating Disc Electrode Atomic Emission Spectrometry |
| ASTM D 5985 : 1996 : EDT 1 | Standard Test Method for Pour Point of Petroleum Products (Rotational Method) |
| ASTM D 7344 : 2017 : REV A | Standard Test Method for Distillation of Petroleum Products and Liquid Fuels at Atmospheric Pressure (Mini Method) |
| ASTM D 7344 : 2014 | Standard Test Method for Distillation of Petroleum Products and Liquid Fuels at Atmospheric Pressure (Mini Method) |
| ASTM D 3828 : 2016 : REV A | Standard Test Methods for Flash Point by Small Scale Closed Cup Tester |
| ASTM D 5453 : 2016 | Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence |
| ASTM D 7042 : 2004 | Standard Test Method for Dynamic Viscosity and Density of Liquids by Stabinger Viscometer (and the Calculation of Kinematic Viscosity) |
| ASTM D 4418 : 1988 : R1998 | Standard Practice for Receipt, Storage, and Handling of Fuels for Gas Turbines |
| ASTM D 7042 : 2019 | Standard Test Method for Dynamic Viscosity and Density of Liquids by Stabinger Viscometer (and the Calculation of Kinematic Viscosity) |
| ASTM D 4418 : 2000 : R2016 | Standard Practice for Receipt, Storage, and Handling of Fuels for Gas Turbines |
| ASTM D 2709 : 1988 | Standard Test Method for Water and Sediment in Distillate Fuels by Centrifuge |
| ASTM D 7345 : 2007 | Standard Test Method for Distillation of Petroleum Products at Atmospheric Pressure (Micro Distillation Method |
| ASTM D 6469 : 1999 | Standard Guide for Microbial Contamination in Fuels and Fuel Systems |
| ASTM D 5453 : 2019 : REV A | Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence |
| ASTM D 7345 : 2014 | Standard Test Method for Distillation of Petroleum Products and Liquid Fuels at Atmospheric Pressure (Micro Distillation Method) |
| ASTM D 1298 : 1985 : R1990 : EDT 1 | Standard Practice for Density, Relative Density (Specific Gravity), or API Gravity of Crude Petroleum and Liquid Petroleum Products by Hydrometer Method |
| ASTM D 4294 : 2016 | Standard Test Method for Sulfur in Petroleum and Petroleum Products by Energy Dispersive X-ray Fluorescence Spectrometry |
| ASTM D 1796 : 1983 : R1990 : EDT 1 | Standard Test Method for Water and Sediment in Fuel Oils by the Centrifuge Method (Laboratory Procedure) |
| ASTM D 7094 : 2004 | Standard Test Method for Flash Point by Modified Continuously Closed Cup (MCCCFP) Tester |
| ASTM D 7344 : 2007 | Standard Test Method for Distillation of Petroleum Products at Atmospheric Pressure (Mini Method) |
| ASTM D 1552 : 1983 | Standard Test Method for Sulfur in Petroleum Products (High-Temperature Method) |
| ASTM D 3828 : 2016 | Standard Test Methods for Flash Point by Small Scale Closed Cup Tester |
| ASTM D 4294 : 1990 : R1998 : EDT 1 | Standard Test Method for Sulfur in Petroleum Products by Energy-Dispersive X-Ray Fluorescence Spectroscopy |
| ASTM D 7094 : 2017 | Standard Test Method for Flash Point by Modified Continuously Closed Cup (MCCCFP) Tester |
| ASTM D 3828 : 1997 | Standard Test Methods for Flash Point by Small Scale Closed Tester |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.