ASTM D 2880 : 2018
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Gas Turbine Fuel Oils
Hardcopy , PDF
10-16-2018
English
05-01-2018
Important note : All end users must be registered with an Account prior to user licenses being assigned.This specification covers the selection of fuels for gas turbines, excepting gas turbines used in aircraft, for the guidance of interested parties such as turbine manufacturers and the suppliers and purchasers of fuel oils.
| Committee |
D 02
|
| DocumentType |
Standard
|
| Pages |
8
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This specification covers the selection of fuels for gas turbines, excepting gas turbines used in aircraft, for the guidance of interested parties such as turbine manufacturers and the suppliers and purchasers of fuel oils. The specification sets forth the properties of fuels at the time and place of custody transfer to the user.
1.2Three appendixes are provided for informational purposes only and do not constitute a requirement of this specification unless mutually agreed upon between the interested parties.
1.2.1Appendix X1 describes the five grades of gas turbine fuels covered by this specification. Further, it states the significance of various test methods used in inspecting the fuels.
1.2.2Appendix X2 discusses the sources of fuel contaminants and notes the significance of such contaminants in the operation of gas turbines and gas turbine fuel systems. The particular significance of trace metals in gas turbine fuels is noted. Upper limits of trace metals are recommended for the various grades of gas turbine fuels, but these recommended limits do not constitute a requirement of the specification unless mutually agreed upon by the interested parties. Limitations due to the use of used or recycled oil are also noted.
Note 1:The gas turbine operator should consult Practice D4418 for methods of ensuring fuels of adequate cleanliness and for guidance on long-term storage of distillate fuels and on liquids from non-petroleum sources as gas turbine.
Note 2:Nothing in this specification shall preclude observance of federal, state, or local regulations which may be more restrictive.
Note 3:The generation and dissipation of static electricity can create problems in the handling of distillate gas turbine fuel oils. For more information on the subject, see Guide D4865.
1.3This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM D 2068 : 2017 | Standard Test Method for Determining Filter Blocking Tendency |
| ASTM D 7112 : 2019 | Standard Test Method for Determining Stability and Compatibility of Heavy Fuel Oils and Crude Oils by Heavy Fuel Oil Stability Analyzer (Optical Detection) |
| ASTM D 4868 : 2017 | Standard Test Method for Estimation of Net and Gross Heat of Combustion of Hydrocarbon Burner and Diesel Fuels |
| ASTM D 4418 : 2017 | Standard Practice for Receipt, Storage, and Handling of Fuels for Gas Turbines |
| ASTM D 6468 : 2008 : R2019 | Standard Test Method for High Temperature Stability of Middle Distillate Fuels |
| ASTM D 7451 : 2016 | Standard Test Method for Water Separation Properties of Light and Middle Distillate, and Compression and Spark Ignition Fuels |
| ASTM D 7060 : 2012 : R2014 | Standard Test Method for Determination of the Maximum Flocculation Ratio and Peptizing Power in Residual and Heavy Fuel Oils (Optical Detection Method) |
| ASTM D 7827 : 2012 : R2017 | Standard Test Method for Measuring n-Heptane Induced Phase Separation of Asphaltene from Heavy Fuel Oils as Separability Number by an Optical Device |
| ASTM D 6426 : 2018 | Standard Test Method for Determining Filterability of Middle Distillate Fuel Oils |
| ASTM D 6469 : 2017 | Standard Guide for Microbial Contamination in Fuels and Fuel Systems |
| ASTM D 7467 : 2019 | Standard Specification for Diesel Fuel Oil, Biodiesel Blend (B6 to B20) |
| ASTM D 6728 : 2016 | Standard Test Method for Determination of Contaminants in Gas Turbine and Diesel Engine Fuel by Rotating Disc Electrode Atomic Emission Spectrometry |
| ASTM D 2709 : 2016 | Standard Test Method for Water and Sediment in Middle Distillate Fuels by Centrifuge |
| ASTM D 975 : 2019 : REV B | Standard Specification for Diesel Fuel |
| ASTM D 6217 : 2018 | Standard Test Method for Particulate Contamination in Middle Distillate Fuels by Laboratory Filtration |
| ASTM D 7157 : 2018 | Standard Test Method for Determination of Intrinsic Stability of Asphaltene-Containing Residues, Heavy Fuel Oils, and Crude Oils (<emph type="ital">n</emph >-Heptane Phase Separation; Optical Detection) |
| ASTM D 6748 : 2002 : REV A : R2017 | Standard Test Method for Determination of Potential Instability of Middle Distillate Fuels Caused by the Presence of Phenalenes and Phenalenones (Rapid Method by Portable Spectrophotometer) |
| ASTM E 1259 : 2018 | Standard Practice for Evaluation of Antimicrobials in Liquid Fuels Boiling Below 390 °C |
| ASTM D 8166 : 2017 | Standard Test Method for Sizing and Counting Particulates in Light and Middle Distillate Fuels and Biodiesel Blend (B6 to B20) Using Continuous Flow and Bottle Sampler Automatic Particle Counters |
| ASTM D 4625 : 2016 : EDT 1 | Standard Test Method for Middle Distillate Fuel Storage Stability at 43 °C (110 °F) |
| ASTM D 3605 : 2017 | Standard Test Method for Trace Metals in Gas Turbine Fuels by Atomic Absorption and Flame Emission Spectroscopy |
| ASTM D 7061 : 2017 | Standard Test Method for Measuring n-Heptane Induced Phase Separation of Asphaltene-Containing Heavy Fuel Oils as Separability Number by an Optical Scanning Device |
| ASTM D 6756 : 2017 | Standard Test Method for Determination of the Red Dye Concentration and Estimation of the ASTM Color of Diesel Fuel and Heating Oil Using a Portable Visible Spectrophotometer |
| ASTM D 7463 : 2018 | Standard Test Method for Adenosine Triphosphate (ATP) Content of Microorganisms in Fuel, Fuel/Water Mixtures, and Fuel Associated Water |
| ASTM D 7464 : 2014 | Standard Practice for Manual Sampling of Liquid Fuels, Associated Materials and Fuel System Components for Microbiological Testing |
| ASTM D 7619 : 2017 | Standard Test Method for Sizing and Counting Particles in Light and Middle Distillate Fuels, by Automatic Particle Counter |
| ASTM D 7111 : 2016 | Standard Test Method for Determination of Trace Elements in Middle Distillate Fuels by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES) |
| ASTM D 4865 : 2019 | Standard Guide for Generation and Dissipation of Static Electricity in Petroleum Fuel Systems |
| ASTM D 7687 : 2017 | Standard Test Method for Measurement of Cellular Adenosine Triphosphate in Fuel and Fuel-associated Water With Sample Concentration by Filtration |
| ASTM D 6751 : 2019 | Standard Specification for Biodiesel Fuel Blend Stock (B100) for Middle Distillate Fuels |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.