• Shopping Cart
    There are no items in your cart

ASTM D 2863 : 2000

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by

Standard Test Method for Measuring the Minimum Oxygen Concentration to Support Candle-Like Combustion of Plastics (Oxygen Index)

Available format(s)

Hardcopy , PDF

Superseded date

11-11-2014

Superseded by

ASTM D 2863 : 2006

Language(s)

English

Published date

07-10-2000

US$83.00
Excluding Tax where applicable

Committee
D 20
DocumentType
Test Method
Pages
13
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

1.1 This test method covers a fire-test-response procedure. This test method describes a procedure for measuring the minimum concentration of oxygen that will just support flaming combustion in a flowing mixture of oxygen and nitrogen.

1.2 Methods are provided for testing materials that are structurally self-supporting in the form of vertical bars or sheet up to 10.5 mm thick. These methods are suitable for solid, laminated or cellular materials characterized by an apparent density greater than 15 kg/m3. The methods may also be applicable to some cellular materials having an apparent density of less than 15kg/m3. A method is provided for testing flexible sheet or film materials while supported vertically.

Note 1--Although this test method has been found applicable for testing other materials, the precision of the test method has not been determined for these materials, or for specimen geometry's and test conditions outside those recommended herein.

1.3 This test method may be used to measure and describe the properties of materials, products, or assemblies in response to heat and flame under controlled laboratory conditions and shall not be used to describe or appraise the fire hazard or fire risk of materials, products, or assemblies under actual fire conditions. However, results of this test may be used as elements of a fire risk assessment which takes into account all of the factors which are pertinent to an assessment of the fire hazard of a particular end use.

1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific hazards statements are given in Note 2.

Note 2: Warning: During the course of combustion, gases or vapors, or both, are evolved which may be hazardous to personnel.

Note 3--This test method and ISO 4589-2 are technically equivalent when using the Type A gas measurement and control device accuracy as described in 6.4.

ASTM C 578 : 2019 Standard Specification for Rigid, Cellular Polystyrene Thermal Insulation
ASTM D 4819 : 2013 Standard Specification for Flexible Cellular Materials Made From Polyolefin Plastics
ASTM G 125 : 2000 : R2015 Standard Test Method for Measuring Liquid and Solid Material Fire Limits in Gaseous Oxidants
ASTM C 1410 : 2017 Standard Specification for Cellular Melamine Thermal and Sound-Absorbing Insulation
ASTM D 3575 : 2014 Standard Test Methods for Flexible Cellular Materials Made From Olefin Polymers
ASTM G 114 : 2014 Standard Practices for Evaluating the Age Resistance of Polymeric Materials Used in Oxygen Service
ASTM D 3013 : 2013 Standard Specification for Epoxy Molding Compounds
ASTM D 8033 : 2016 Standard Classification System for Poly(Ether Ether Ketone) (PEEK) Molding and Extrusion Materials
ASTM G 128/G128M : 2015 Standard Guide for Control of Hazards and Risks in Oxygen Enriched Systems
ASTM F 1870 : 2016 Standard Guide for Selection of Fire Test Methods for the Assessment of Upholstered Furnishings in Detention and Correctional Facilities
ASTM D 5575 : 2018 Standard Classification System for Copolymers of Vinylidene Fluoride (VDF) with Other Fluorinated Monomers
ASTM D 5205 : 2016 Standard Classification System and Basis for Specification for Polyetherimide (PEI) Materials
ASTM G 126 : 2016 Standard Terminology Relating to the Compatibility and Sensitivity of Materials in Oxygen Enriched Atmospheres
ASTM D 6817/D6817M : 2017 Standard Specification for Rigid Cellular Polystyrene Geofoam
ASTM G 94 : 2005 : R2014 Standard Guide for Evaluating Metals for Oxygen Service
ASTM D 4649 : 2003 : R2016 Standard Guide for Selection and Use of Stretch Wrap Films
ASTM D 1636 : 2013 Standard Specification for Allyl Molding Compounds
ASTM D 4000 : 2016 Standard Classification System for Specifying Plastic Materials
ASTM D 3275 : 2018 Standard Classification System for E-CTFE-Fluoroplastic Molding, Extrusion, and Coating Materials
ASTM C 1594 : 2011 : R2017 Standard Specification for Polyimide Rigid Cellular Thermal Insulation
ASTM G 63 : 2015 Standard Guide for Evaluating Nonmetallic Materials for Oxygen Service
ASTM G 127 : 2015 Standard Guide for the Selection of Cleaning Agents for Oxygen-Enriched Systems
ASTM D 3664 : 2016 Standard Specification for Biaxially Oriented Polymeric Resin Film for Capacitors in Electrical Equipment (Withdrawn 2022)

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.