ASTM D 2673 : 2014
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Oriented Polypropylene Film
Available format(s)
Hardcopy , PDF
Superseded date
04-28-2022
Superseded by
Language(s)
English
Published date
09-11-2014
Important note : All end users must be registered with an Account prior to user licenses being assigned.| Committee |
D 20
|
| DocumentType |
Standard
|
| Pages |
4
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This specification covers oriented polypropylene (OPP) film in the thickness range from 10 to 75 μm (0.4 to 3.0 mils).
1.2The film can contain colorants, stabilizers, or other additives, and can be coated for the improvement of performance properties (heat sealability, gas permeability, and so forth).
1.3The film can be annealed (heat-set) to reduce the unrestrained linear shrinkage and shrink tension on exposure to heat.
1.4The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only.
1.5The following safety hazards caveat pertains only to the test methods portion, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Note 1:There is no known ISO equivalent to this standard.
| ASTM D 2732 : 2008 | Standard Test Method for Unrestrained Linear Thermal Shrinkage of Plastic Film and Sheeting |
| ASTM D 1746 : 1997 | Standard Test Method for Transparency of Plastic Sheeting |
| ASTM D 4101 : 2001 : REV A | Standard Specification for Polypropylene Injection and Extrusion Materials |
| ASTM E 1870 : 2011 | Standard Test Method for Odor and Taste Transfer from Polymeric Packaging Film |
| ASTM D 4101 : 2001 | Standard Specification for Polypropylene Injection and Extrusion Materials |
| ASTM D 4101 : 2006 : REV B | Standard Specification for Polypropylene Injection and Extrusion Materials |
| ASTM D 4101 : 2005 | Standard Specification for Polypropylene Injection and Extrusion Materials |
| ASTM D 6988 : 2008 | Standard Guide for Determination of Thickness of Plastic Film Test Specimens |
| ASTM D 4101 : 2000 | Standard Specification for Polypropylene Injection and Extrusion Materials |
| ASTM D 1894 : 2011 | Standard Test Method for Static and Kinetic Coefficients of Friction of Plastic Film and Sheeting |
| ASTM D 1922 : 2008 | Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method |
| ASTM D 2578 : 2009 | Standard Test Method for Wetting Tension of Polyethylene and Polypropylene Films |
| ASTM D 4000 : 2013 | Standard Classification System for Specifying Plastic Materials |
| ASTM D 4101 : 2008 | Standard Specification for Polypropylene Injection and Extrusion Materials |
| ASTM D 4321 : 2004 | Standard Test Method for Package Yield of Plastic Film |
| ASTM D 2732 : 2014 : R2020 | Standard Test Method for Unrestrained Linear Thermal Shrinkage of Plastic Film<brk/> and Sheeting |
| ASTM D 3354 : 2008 | Standard Test Method for Blocking Load of Plastic Film by the Parallel Plate Method |
| ASTM D 3892 : 2015 : R2020 | Standard Practice for Packaging/Packing of Plastics |
| ASTM D 1434 : 1982 : R2003 | Standard Test Method for Determining Gas Permeability Characteristics of Plastic Film and Sheeting |
| ASTM D 4101 : 2006 | Standard Specification for Polypropylene Injection and Extrusion Materials |
| ASTM D 4101 : 2004 | Standard Specification for Polypropylene Injection and Extrusion Materials |
| ASTM D 1003 : 2007 | Standard Test Method for Haze and Luminous Transmittance of Transparent Plastics |
| ASTM D 4101 : 2014 : EDT 2 | Standard Specification for Polypropylene Injection and Extrusion Materials |
| ASTM D 4000 : 2003 : REV A | Standard Classification System for Specifying Plastic Materials |
| ASTM D 6988 : 2021 | Standard Guide for Determination of Thickness of Plastic Film Test Specimens |
| ASTM D 4000 : 2000 : REV A | Standard Classification System for Specifying Plastic Materials |
| ASTM D 4101 : 2010 | Standard Specification for Polypropylene Injection and Extrusion Materials |
| ASTM D 4101 : 2011 | Standard Specification for Polypropylene Injection and Extrusion Materials |
| ASTM D 4000 : 2012 | Standard Classification System for Specifying Plastic Materials |
| ASTM D 4000 : 2009 | Standard Classification System for Specifying Plastic Materials |
| ASTM D 4101 : 2005 : REV A | Standard Specification for Polypropylene Injection and Extrusion Materials |
| ASTM D 1003 : 2013 | Standard Test Method for Haze and Luminous Transmittance of Transparent Plastics |
| ASTM E 96/E96M : 2021 | Standard Test Methods for Gravimetric Determination of Water Vapor Transmission Rate of Materials |
| ASTM D 4321 : 1999 | Standard Test Method for Package Yield of Plastic Film |
| ASTM D 2838 : 2008 | Standard Test Method for Shrink Tension and Orientation Release Stress of Plastic Film and Thin Sheeting |
| ASTM D 1922 : 2015 | Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method |
| ASTM D 2457 : 2008 | Standard Test Method for Specular Gloss of Plastic Films and Solid Plastics |
| ASTM D 2578 : 2008 | Standard Test Method for Wetting Tension of Polyethylene and Polypropylene Films |
| ASTM D 3892 : 1993 : R2003 | Standard Practice for Packaging/Packing of Plastics |
| ASTM D 3892 : 2015 | Standard Practice for Packaging/Packing of Plastics |
| ASTM D 1894 : 2000 | Standard Test Method for Static and Kinetic Coefficients of Friction of Plastic Film and Sheeting |
| ASTM D 1922 : 2006 : REV A | Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method |
| ASTM D 4101 : 2007 | Standard Specification for Polypropylene Injection and Extrusion Materials |
| ASTM D 3985 : 2005 | Standard Test Method for Oxygen Gas Transmission Rate Through Plastic Film and Sheeting Using a Coulometric Sensor |
| ASTM D 5946 : 2004 | Standard Test Method for Corona-Treated Polymer Films Using Water Contact Angle Measurements |
| ASTM D 4101 : 2002 : REV A | Standard Specification for Polypropylene Injection and Extrusion Materials |
| ASTM D 4000 : 2011 | Standard Classification System for Specifying Plastic Materials |
| ASTM D 1894 : 2001 | Standard Test Method for Static and Kinetic Coefficients of Friction of Plastic Film and Sheeting |
| ASTM D 2578 : 1999 : REV A | Standard Test Method for Wetting Tension of Polyethylene and Polypropylene Films |
| ASTM D 6988 : 2003 | Standard Guide for Determination of Thickness of Plastic Film Test Specimens |
| ASTM D 5946 : 2009 | Standard Test Method for Corona-Treated Polymer Films Using Water Contact Angle Measurements |
| ASTM D 4101 : 2003 : REV B | Standard Specification for Polypropylene Injection and Extrusion Materials |
| ASTM D 3354 : 2015 | Standard Test Method for Blocking Load of Plastic Film by the Parallel Plate Method |
| ASTM D 3892 : 1993 : R1998 | Standard Practice for Packaging/Packing of Plastics |
| ASTM D 2578 : 2017 | Standard Test Method for Wetting Tension of Polyethylene and Polypropylene Films |
| ASTM D 3985 : 2005 : R2010 : EDT 1 | Standard Test Method for Oxygen Gas Transmission Rate Through Plastic Film and Sheeting Using a Coulometric Sensor |
| ASTM D 3985 : 2002 : EDT 1 | Standard Test Method for Oxygen Gas Transmission Rate Through Plastic Film and Sheeting Using a Coulometric Sensor |
| ASTM D 3354 : 1996 | Standard Test Method for Blocking Load of Plastic Film by the Parallel Plate Method |
| ASTM D 4101 : 2002 : REV B | Standard Specification for Polypropylene Injection and Extrusion Materials |
| ASTM D 4000 : 2004 : EDT 1 | Standard Classification System for Specifying Plastic Materials |
| ASTM D 1746 : 2003 | Standard Test Method for Transparency of Plastic Sheeting |
| ASTM D 2732 : 1996 | Standard Test Method for Unrestrained Linear Thermal Shrinkage of Plastic Film and Sheeting |
| ASTM D 4321 : 2009 | Standard Test Method for Package Yield of Plastic Film |
| ASTM D 4101 : 2009 | Standard Specification for Polypropylene Injection and Extrusion Materials |
| ASTM D 2732 : 2003 | Standard Test Method for Unrestrained Linear Thermal Shrinkage of Plastic Film and Sheeting |
| ASTM D 1003 : 2007 : EDT 1 | Standard Test Method for Haze and Luminous Transmittance of Transparent Plastics |
| ASTM D 5946 : 1999 | Standard Test Method for Corona-Treated Polymer Films Using Water Contact Angle Measurements |
| ASTM D 4101 : 2006 : REV A | Standard Specification for Polypropylene Injection and Extrusion Materials |
| ASTM D 1894 : 2014 | Standard Test Method for Static and Kinetic Coefficients of Friction of Plastic Film and Sheeting (Withdrawn 2023) |
| ASTM D 4000 : 2009 : REV B | Standard Classification System for Specifying Plastic Materials |
| ASTM D 1922 : 2003 | Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method |
| ASTM D 4000 : 2000 | Standard Classification System for Specifying Plastic Materials |
| ASTM D 4000 : 2010 : REV A | Standard Classification System for Specifying Plastic Materials |
| ASTM D 2457 : 2013 | Standard Test Method for Specular Gloss of Plastic Films and Solid Plastics |
| ASTM D 4101 : 2004 : REV A | Standard Specification for Polypropylene Injection and Extrusion Materials |
| ASTM D 4101 : 1982 : R1988 : EDT 1 | Standard Specification for Propylene Plastic Injection and Extrusion Materials |
| ASTM D 4101 : 2017 | Standard Classification System and Basis for Specification for Polypropylene Injection and Extrusion Materials |
| ASTM D 3354 : 2011 | Standard Test Method for Blocking Load of Plastic Film by the Parallel Plate Method |
| ASTM D 1894 : 2011 : EDT 1 | Standard Test Method for Static and Kinetic Coefficients of Friction of Plastic Film and Sheeting |
| ASTM D 4000 : 2007 | Standard Classification System for Specifying Plastic Materials |
| ASTM D 4000 : 2009 : REV A | Standard Classification System for Specifying Plastic Materials |
| ASTM D 6988 : 2007 | Standard Guide for Determination of Thickness of Plastic Film Test Specimens |
| ASTM D 2838 : 1995 | Standard Test Method for Shrink Tension and Orientation Release Stress of Plastic Film and Thin Sheeting |
| ASTM D 5946 : 2001 | Standard Test Method for Corona-Treated Polymer Films Using Water Contact Angle Measurements |
| ASTM E 96/E96M : 2016 | Standard Test Methods for Water Vapor Transmission of Materials |
| ASTM D 4000 : 2001 | Standard Classification System for Specifying Plastic Materials |
| ASTM D 4101 : 2014 | Standard Specification for Polypropylene Injection and Extrusion Materials |
| ASTM D 1003 : 2011 | Standard Test Method for Haze and Luminous Transmittance of Transparent Plastics |
| ASTM D 4000 : 2008 | Standard Classification System for Specifying Plastic Materials |
| ASTM D 1746 : 2009 | Standard Test Method for Transparency of Plastic Sheeting |
| ASTM D 1922 : 2015 : R2020 | Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method |
| ASTM E 1870 : 2004 | Standard Test Method for Odor and Taste Transfer from Polymeric Packaging Film |
| ASTM D 4101 : 2010 : REV A | Standard Specification for Polypropylene Injection and Extrusion Materials |
| ASTM D 2578 : 2004 | Standard Test Method for Wetting Tension of Polyethylene and Polypropylene Films |
| ASTM D 1003 : 2021 | Standard Test Method for Haze and Luminous Transmittance of Transparent Plastics |
| ASTM D 2457 : 1997 | Standard Test Method for Specular Gloss of Plastic Films and Solid Plastics |
| ASTM D 1434 : 1982 : R2015 : EDT 1 | Standard Test Method for Determining Gas Permeability Characteristics of Plastic Film and Sheeting |
| ASTM D 618 : 2013 | Standard Practice for Conditioning Plastics for Testing |
| ASTM E 1870 : 2011 : R2019 | Standard Test Method for Odor and Taste Transfer from Polymeric Packaging Film |
| ASTM D 1922 : 2003 : REV A | Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method |
| ASTM D 4000 : 2001 : REV A : EDT 1 | Standard Classification System for Specifying Plastic Materials |
| ASTM D 4101 : 2003 | Standard Specification for Polypropylene Injection and Extrusion Materials |
| ASTM D 4000 : 2004 | Standard Classification System for Specifying Plastic Materials |
| ASTM D 3985 : 1995 | Standard Test Method for Oxygen Gas Transmission Rate Through Plastic Film and Sheeting Using a Coulometric Sensor |
| ASTM D 1434 : 1982 : R2009 : EDT 1 | Standard Test Method for Determining Gas Permeability Characteristics of Plastic Film and Sheeting |
| ASTM D 4101 : 2003 : REV A | Standard Specification for Polypropylene Injection and Extrusion Materials |
| ASTM D 6988 : 2013 | Standard Guide for Determination of Thickness of Plastic Film Test Specimens |
| ASTM D 1746 : 2015 | Standard Test Method for Transparency of Plastic Sheeting |
| ASTM D 1003 : 2000 | Standard Test Method for Haze and Luminous Transmittance of Transparent Plastics |
| ASTM D 5946 : 2017 | Standard Test Method for Corona-Treated Polymer Films Using Water Contact Angle Measurements |
| ASTM D 2732 : 2014 | Standard Test Method for Unrestrained Linear Thermal Shrinkage of Plastic Film<brk/> and Sheeting |
| ASTM D 1922 : 2005 | Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method |
| ASTM D 3892 : 1993 : R2009 | Standard Practice for Packaging/Packing of Plastics |
| ASTM D 4000 : 2010 | Standard Classification System for Specifying Plastic Materials |
| ASTM D 3354 : 2021 | Standard Test Method for Blocking Load of Plastic Film by the Parallel Plate Method |
| ASTM D 1894 : 2008 | Standard Test Method for Static and Kinetic Coefficients of Friction of Plastic Film and Sheeting |
| ASTM D 2838 : 2009 : EDT 1 | Standard Test Method for Shrink Tension and Orientation Release Stress of Plastic Film and Thin Sheeting (Withdrawn 2018) |
| ASTM D 4101 : 2002 | Standard Specification for Polypropylene Injection and Extrusion Materials |
| ASTM D 2838 : 2007 | Standard Test Method for Shrink Tension and Orientation Release Stress of Plastic Film and Thin Sheeting |
| ASTM D 2457 : 2003 | Standard Test Method for Specular Gloss of Plastic Films and Solid Plastics |
| ASTM D 1003 : 2011 : EDT 1 | Standard Test Method for Haze and Luminous Transmittance of Transparent Plastics |
| ASTM D 1922 : 2000 : REV A | Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method |
| ASTM D 3354 : 2004 | Standard Test Method for Blocking Load of Plastic Film by the Parallel Plate Method |
| ASTM D 3985 : 2002 | Standard Test Method for Oxygen Gas Transmission Rate Through Plastic Film and Sheeting Using a Coulometric Sensor |
| ASTM D 4101 : 2017 : EDT 1 | Standard Classification System and Basis for Specification for Polypropylene Injection and Extrusion Materials |
| ASTM D 4000 : 2003 | Standard Classification System for Specifying Plastic Materials |
| ASTM D 1894 : 2006 | Standard Test Method for Static and Kinetic Coefficients of Friction of Plastic Film and Sheeting |
| ASTM D 1003 : 1992 | Standard Test Method for Haze and Luminous Transmittance of Transparent Plastics |
| ASTM E 1870 : 1998 | Standard Test Method for Odor and Taste Transfer from Polymeric Packaging Film |
| ASTM D 2838 : 2009 | Standard Test Method for Shrink Tension and Orientation Release Stress of Plastic Film and Thin Sheeting |
| ASTM D 3985 : 2017 | Standard Test Method for Oxygen Gas Transmission Rate Through Plastic Film and Sheeting Using a Coulometric Sensor |
| ASTM D 2457 : 2021 | Standard Test Method for Specular Gloss of Plastic Films and Solid Plastics |
| ASTM D 2457 : 2008 : EDT 1 | Standard Test Method for Specular Gloss of Plastic Films and Solid Plastics |
| ASTM D 4101 : 2014 : EDT 1 | Standard Specification for Polypropylene Injection and Extrusion Materials |
| ASTM D 1922 : 2006 | Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method |
| ASTM D 2838 : 2002 | Standard Test Method for Shrink Tension and Orientation Release Stress of Plastic Film and Thin Sheeting |
| ASTM D 2578 : 2004 : REV A | Standard Test Method for Wetting Tension of Polyethylene and Polypropylene Films |
| ASTM D 4321 : 2015 | Standard Test Method for Package Yield of Plastic Film (Withdrawn 2024) |
| ASTM D 618 : 2021 | Standard Practice for Conditioning Plastics for Testing |
| ASTM D 1922 : 2009 | Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method |
| ASTM D 1434 : 1982 : R1998 | Standard Test Method for Determining Gas Permeability Characteristics of Plastic Film and Sheeting |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.